Question about 2002 Isuzu Axiom
You have a bunch of pipes under there that carry coolant to the rear of the engine, they have O-rings that go bad, you have to remove the intake to get to them and half the pipes from the cooling system, it is a job, but it can be done. I just did mine. You will need the top gasket kit for the intake and the O-rings are just reg, off the shelf stuff, nothing fancy. If you have anything else back there you might want to replace, do it now while you are there, because it is a job getting in there. There are a couple of sensors under there, and some other goodies, you will have to check them out while you are at it. Hope this helps.
Posted on Jul 28, 2010
Sounds like a frost plug needs replaced.adrian,,,,
Posted on Jul 28, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1996 lincoln towncar
If you have a pipe leaking you need to replace it. Only onei can think of thats close to intake is the In/out to heater matrix.
But if its leaking from waterpump it need a new gasket.
Posted on Jan 23, 2009
Sorry im late with this,i couldnt seem to log on....The answer to your question is YES,there is a steel line under the intake with a short piece of rubber line attached to it and you can just about see it from the front of the intake with a light,it can leak and cause coolant to run off the back of the engine,The intake gasket set alone is about $40.00 and i dont know about the rubber line,i have seen it physically but havent changed one yet.Note the date of manufactor just incase,i bought an intake set for a 99 and the engine design was changed half way through...its not too hard to pull off the intake and re-install,you will need a 7mm socket for the coil packs,8mm socket for the fuel rail bolts and lower intake bolts and power steering bracket bolts and throttle bracket bolts,10mm socket for the intake bolts and alternator bolts and egr valve,and a large cresant wrench for the exhaust tube thats connected to the egr valve,flat screw driver for the air cleaner...and plenty of extensions with a swivel to be able to get to the back bolts of the intake....just incase you do it yourself this info could make it easier to gather tools.Its about a 3 1\2 to 4 hour job start to finish for the first time doing it,includes cleaning everything..Good luck
Posted on May 16, 2009
SOURCE: intake? coolant leak
This is a common problem with this engine. The gaskets between the intake manifold and the heads need to be replaced. This will require other gaskets, seals and o-rings. Fel-pro makes a intake gasket kit that comes with everything "gaskets and seals" in it. Ask for the perma-dry gasket if available.
Posted on May 19, 2009
Yes this models tend to do that, check the coolant mixture after repair, yes is a diy proyect but you at least will have basic mechanic abilities to perform this, make sure you mark all the hoses and cables when dismantling.
Posted on Jul 08, 2009
Tips for a great answer:
Sep 25, 2015 | Pontiac Cars & Trucks
Mar 20, 2012 | Nissan Cars & Trucks
Jan 22, 2011 | Chevrolet 1500 Cars & Trucks
Oct 19, 2009 | 1999 GMC Jimmy
Oct 10, 2009 | 1995 GMC Yukon
Apr 05, 2009 | 1989 Dodge Daytona
Mar 18, 2009 | 1999 Ford Taurus
Jan 02, 2009 | 1994 Chevrolet Caprice Classic
143 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: