Question about 2001 Chevrolet Blazer

2 Answers

How do you take out the battery on 2001 blazer, we disconnected the cables but is it bolted down or something as it wouldn't move?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 62 Answers

It has a small bracket with a bolt through it, I think it takes a 13 or 15mm socket with a long extension to remove, check the bottom part of the battery, hope this helps, Gary

Posted on Jul 28, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Down on bottom side of battery is a battery holder. It is bolted down with a nut you need to unscrew so battery can lift out.

Posted on Jul 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel problem possibly, why would a 2001 blazer, at about 2500 rpms, engine doesn't want to run, bogging down. all started when I had the battery replaced, service engine soon light on also.


You can disconnect the neg, batt, cable for 5 min, and this should reset your systems. Let me know if this doesn't work.

Hope this helps Mike

Feb 08, 2016 | 2001 Chevrolet Chevrolet Blazer

1 Answer

Installed new trans on 01 s10 blazer and it wont move


Disconnect the vehicle battery for an hour and reconnect. Retry once again.

Disconnecting the battery can restore ECU and ECM programming and help to pair systems.


Does this help?

Nov 12, 2012 | Cars & Trucks

2 Answers

My Chevy blazer wouldn't start mad a clicking


this is one of two problems (maybe both) ...
1. The battery has been fully discharged before, preventing it from being able to hold a charge properly. This can be tested at a Sears Automotive Center. If the battery is no good, get a replacement and you should be fine (at least for a while). If you are going to go to Sears, have them run a full electrical diagnostic -- if there is something draining your battery while the car is not in use changing the battery will only hide the problem for a few months until the new battery fully discharges, and the same issue with resurface.
2. Your alternator is not charging the battery. It might be pumping out electricity to the wiring that it is connected to, but the charge may not be getting all the way to the battery. Sears can also check this with their diagnostic tools, and should be able to locate and repair the problem for you. Unfortunately, without a VERY expensive diagnostic machine, it is very hard to tell exactly where the problem is occurring .. so taking it in to a shop is probably your best bet.

May 27, 2011 | 2001 Chevrolet Blazer

1 Answer

How do you remove glove box 2001 Chevrolet blazer


OPEN AND LOOK INSIDE GLOVE COMPARTMENT LOOK ON THE INNER EDGES OF THE FOUR CORNERS YOU WILL SEE SMALL BOLTS HOLDING THE GLOVE BOX IN THE DASH. YOU NEED TO DISARM AIRBAGS SYSTEM.BECAUSE AIR BAG ABOVE THE GLOVE BOX.TURN OFF RADIO FIRST.THEN DISCONNECT NEGATIVE BATTERY CABLE.WAIT 20 MINUTES FOR AIR BAGS TO DISCHARGE BEFORE WORKING AROUND DASH AREA.

Apr 13, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

How to change front wheel bearing on 2001 blazer


You'll need to disconnect the tierod end from the steering knuckle, remove the caliper, caliper carrier, rotor and disconnect the ABS plug. Then disconnect the upper and lower ball joints and remove the steering knuckle. The wheel bearing hub has 3 bolts holding it to the steering knuckle, from the back side.

May 11, 2010 | 2001 Chevrolet Blazer

1 Answer

1985 Chevy Blazer 4x4 2.8L V6 - engine wont start. However, when I dumped a small amount of fuel in carb - it started briefly. Is this a fuel pump issue - if so where is it located? Or can it be something...


You should see gas squirt in the carb with the movement of the linkage....if not, bad fuel pump.

2.8L Engine The fuel pump is located on the front left side of the engine.
  1. Disconnect the negative battery cable.
  2. Disconnect the fuel hoses from the pump. If necessary, tag the lines to assure proper installation.
  3. Remove the fuel pump-to-engine bolts and remove the fuel pump from the engine, then remove and discard the old gasket.
To install:
Before installing the fuel pump, it may be helpful to rotate the crankshaft so that the cam lobe is on the down stroke.
  1. Use a new gasket and RTV sealant, then install the pump to the engine.
  2. Tighten the fuel pump-to-engine bolts to 15 ft. lbs. (20 Nm).
  3. Connect the fuel hoses to the pump, as noted during removal.
  4. Connect the negative battery cable, then start the engine and check for proper pump operation.

May 05, 2010 | 1985 Chevrolet S-10 Blazer

1 Answer

How to remove a driverside pwr seat from a 1998 chevy s10 blazer


the seat is mounted to either studs or bolted down, there are two in the front and two in the rear, raise the seat up as high as it goes and disconnect the wiring harness, be carefull not to break the connector, move the seat back and remove the front nuts or bolts on floor, there may be a trim cover over them, repeat for rear, move seat foreward to access rear nuts or bolts (varies by year.)

Oct 20, 2009 | 1998 Chevrolet Blazer

1 Answer

How can i get the oil pan out on a 2001 chevy malibu?


2.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan


  1. Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm).
  2. Accessory drive belt
  3. Negative battery cable

  4. Fill the engine with oil to the correct level.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan

To install:
  1. Apply a 0.13 inch (3.5mm) bead of the GM P/N 12378521 sealant around the perimeter of the oil pan and oil suction port opening.
  2. Install or connect the following:

    Oil pan. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).

    0900c1528024bb26.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Oil pan bolt sequence-2.2L engine
    Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm). Accessory drive belt Negative battery cable
  3. Fill the engine with oil to the correct level.
3.1L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Evacuate and recover the A/C system.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    WARNING DO NOT disconnect the refrigerant lines or allow the compressor to hang unsupported.


    Negative battery cable Accessory drive belt Upper and lower radiator hoses Right front wheel Inner fender splash shield Antilock Brake System (ABS) Wheel Speed Sensor (WSS) electrical connector Right front ball joint from the steering knuckle Right side outer tie rod end A/C compressor bolts and move the compressor aside


    Evaporator-to-accumulator A/C line Flywheel cover Engine cradle bolts Crankshaft balancer Starter motor Oil pan

To install:

0900c1528024bb27.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the oil pan mounting-3.1L and 3.5L engines

  1. Install or connect the following:

Sep 02, 2009 | 2001 Chevrolet Malibu

1 Answer

My 2001 chrysler concord started fine this afternoon but a couple hours later when i went to start my car I just heard click click click... the lights & windows & radio all work & I tried to jumping it but...


Check your started connections and battery connections ..

It is behind the front passenger wheel fender

The battery is buried within the front section of the passenger side front fender.

Disconnect the neg battery cable close to the firewall.

Remove the bolts holding the air cleaner assembly in place.

(Removing the air feed tube from the air cleaner assembly helps)

Once this is removed, you should be able to see the battery hold-down bolts.

Remove these and remove the hold-down assembly.

If you are removing the battery, remove the 1st battery cable.

Depending upon what battery you have, you may be able to slide the battery back toward the wheel and disconnect the 2nd cable.

Jack the vehicle up, put on jack stands and remove the passenger side wheel.

On the front side of the wheel well there is an access panel that needs to be removed in order to access the battery. There are 6-8 1/4" screws to remove. Then manipulate the cover until you can remove it, bending it slightly.

If you were unable to disconnect the 2nd battery cable earlier, you can now move the battery further towards the rear of the car.

Remove the 2nd cable clamp from under the hood.

Slide the battery all the way out. It is heavy!

Reverse the instructions for reassembly.

Hope this helps.....

Mar 21, 2009 | 2001 Chrysler Concorde

4 Answers

2001 chevrolet blazer hood latch won't release and open hood


if the cable is not broken then pull the release then take the side of your fist and pound on the hood starting towards the top drivers side and slowly move towards the latch try it a few times i have to do this every single time on my blazer

Mar 18, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...