Question about 1984 Oldsmobile Delta 88

1 Answer

Need new headers what fits

Need new headers what fits

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 91 Answers

You can buy new headers from your local auto parts store.

Posted on Jul 28, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can I Fit a performance starter into a '78 Ford 250 with Cleveland engine

Fit a heat shield over the starter motor and wrap asbestos lagging on the header

Apr 13, 2014 | Cars & Trucks

1 Answer

Header tank cap seperation

you have one of the faulty caps that were made you are going to need to replace it with a new one. you will need to prise out the bit stuck with a screw driver and lift it out if any parts brake off you need to take the coolant tank off and empty the broken bits/s out. caps are cheap to replace.. off ebay

Mar 09, 2014 | Vauxhall Cars & Trucks

1 Answer

Kia carnival 1999 v 6 over heating already replaced radiator cap, water pump.thermostat

check radiator is not blocked, check air can pass through radiator (fins not blocked with debris) check that there is no airlock in system. is header tank being pressurised when engine running ( remove cap and start engine, look for bubbles in header tank). If bubbles then you need to check head gasket or even crack in head or cylinder walls. Presume you fitted the thermostat in the right way round. if you have boiled the engine since fitting the thermostat you will probably need to remove it (maybe see if it boils without it fitted) and possibly replace it again. (drop in hot water and see if it opens, if it doesn't then replace it)

Jun 19, 2012 | Kia Carnival Cars & Trucks

1 Answer

How to install headers on a 2001 chevy 4.3

You are wanting to put headers on a Blazer? Power to ya, dude! I doubt if anyone can tell you how to do it other than unbolt the existing manifolds and bolt the headers in....hope they fit...

Have you thought about what you are going to do with the REST of the exhaust system? Like the O2 sensors, catalytic converter, etc.? Install headers because it sounds cool and all your buddies will be impressed with all the "power" it gives your Blazer...only to totally mess up your fuel control and have it run like ****???

I don't get it.....

Good luck

May 11, 2012 | 2000 Chevrolet Blazer

1 Answer

93 Chevy engine has code 43 problems I no it could be a bad knock sensor. My problem is I had headers put on . They were a tight fit in the area of the sensor, I did not do the work. The sensor is screwed...

Should be another sensor on other side of engine practice unplugging that one to see why this one is difficult then gotta get header tube off fitting or move fitting position so it clears I would imagine it worked out before if not things may get tougher but fixable I won't advise it but a good pinch bar and wedge would be an option start engine get headers cherry red and work quickly gotta be brave and crazy with care it's an extreme that most should pass on for all the things that could go wrong I'm guessing you better not go there new headders are pretty cheap.

Apr 02, 2012 | 1993 Chevrolet K1500

1 Answer

Installing headers on 91 ranger and insatting y pipe is about 1/4 to short to con headers any suggestions

Look to see where the pipe is hitting underneath and bend them in at that point if possible. Almost all headers have to be modified to fit. It if looks like they are not going to fit don't bend them, send them back.

Jun 26, 2011 | Ford Ranger Cars & Trucks

1 Answer

1994 Bronco Egr valve doesnt fit into new ****** headers

They sold you a set of headers that don't accommodate the EGR valve line. You can buy headers that have the bung welded into them for the connection. If you do not connect the EGR then you exhaust gas temps will run high and pinging will likely be the result. Excessive preignition can cause valve and piston damage. The lack of the EGR valve may cause you to not pass your states emissions test. I would purchase a set of headers that have the hook up on them. Try Gibson headers. They sell these.

Feb 17, 2009 | 1994 Ford Bronco

1 Answer

'1993 chevy silverado new motor headers won't fit'

For the cylinder head problem,,you need a set of heads from a Carb'd motor.
For your Header problem, you need the services of your friendly neighborhood Welder.
All things are possible with the right application of enough heat ;-)

Jan 29, 2009 | 1986 Chevrolet K1500

1 Answer

I need to know if HEADER PANEL from a Volvo 850 will work in S70?

there may be a few mods to make but physically it shoul go right in

Nov 21, 2008 | 1984 Volvo 240 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides