Question about 1994 Buick Park Avenue

1 Answer

Brand new a/c compreesorclutch will not engage.ground is good all hook ups good.what is the problem

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 58 Answers

Locate the fuse box that is under the hood should be a black plastic box open it and see if there is a fuse that controls the ac clutch.

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 navigator is blowing ac fuse 11, ac coil shorted, 3 different coils, can ac compress short the coils


How did you hook up the inline fuse to compressor and ground to compress ? Ground what ? Right at the clutch coil ? You have to be hooking it up wrong . The compressor can't cause the clutch coil to short or blow the fuse , even if the compressor were seized up . An before that would have the serpentine belt would burn up , squealing noise. applying B+ voltage in the relay socket ,pin 30 to pin 87 will engage the compressor clutch . If the fuse blows the wiring from the relay to the compressor clutch is shorted to ground . Look for rubbed through wiring harness .

Jul 14, 2017 | Ford Cars & Trucks

1 Answer

Change my starter in a 2005 Acura TL hear a click but the starter is not turn over or engaging can some please give me advice


Make sure battery has a full charge and connections good. Make sure engine isn't froze up. Two voltage circuits at the starter motor, one comes from battery, hot all the time. The other goes hot with key in the crank position. It grounds through the engine block.
Any testing at the starter make sure tranny is in park or neutral and parking brake is set.
The starter motor itself may have a problem? You may be able to remove starter lay it on the ground, hook up jumper cables properly from starter motor to battery. At the least it should kick out the drive gear and spin, of course that is a no load test. Some of the national brand autostores will test the starter for you, if you take it to them.
starter 1-rq0xcbpshleq0uabmr0vfthh-3-0.jpg

starter 2-rq0xcbpshleq0uabmr0vfthh-3-2.jpg

May 27, 2017 | Acura Cars & Trucks

1 Answer

Starter just spins


By, the starter just spins, you mean the starter doesn't engage the flywheel? Maybe the starter is faulty and check the flywheel teeth.

Usually I can remove the starter, lay it on the ground, use jumper cables, properly hooked up between starter and fully charged battery, even though this is a no load test, it should kick out the drive gear and spin. If not, the starter may be faulty? Some of the national brand auto stores will check the starter for you, if you take it to them.
Make sure battery has a full charge and connections all good.

Feb 06, 2016 | 1989 Mercury Cougar

2 Answers

Bendix starter won't engage


What is year--make--model of vehicle?
Some starters you can take it off and lay it on the ground. Hook up jumper cables properly from starter to fully charged battery. At the least, it should kick out the drive gear and spin. That is a no load test. Some of the national brand auto stores will test the starter for you.

Did you check voltage and ground circuits at the starter motor. Any testing at the starter, make sure tranny is in park or neutral and the parking brake is set.

Jan 02, 2016 | Cars & Trucks

1 Answer

I have a 2009 GMC Sierra with towing package and a 7 pin plug on the rear bumper. I hooked up a new trailer with electric brakes and the display on the dash shows "trailer connected" and shows increasing...


It's a very good possibility that it is the trailer. You say that it is new, is it a brand new trailer or just new to you? If it is brand new, and you bought it from a place that deals with trailers, then I would say take it back and have them look over everything. If that's not an option, then it's time to pull out the circuit tester and start checking wires. See if you are getting power to the Blue wire on the trailer, and if so is there power all the way to the brakes. You will need someone to push on the brake pedal while checking the wires. If the power is good all the way to the brakes, then you will need to pull the drums and inspect the brake shoes for wear, and condition of the the brake components. If this is a used trailer, then it would be a good idea to do this anyway so that you can also inspect and grease the bearings. If everything looks good, then the brakes might just need to be adjusted via the slot on the back side of the brake housing. If no power is seen in the blue wire, check the Red wire (12v Aux/charging), if it doesn't have power, then you more than likely have a Ground issue. This can easily be checked by hooking the trailer to the truck (hitch). Both use a chassis ground, and will use the hitch itself as the ground connection, though it is not a good idea to use it as the ground point.

Apr 27, 2014 | 2009 GMC Sierra 1500

1 Answer

Van will not crank or start


solenoid has failed makes the pin come out in the motor so it engages the fly wheel..

Dec 19, 2013 | 1993 Dodge Ram 250

1 Answer

Does the neg. battery cable hook to the starter on a 1996 mercury villager? or some where else?


Yes the neg cable is grounded at the starter bolts and also at the frame.
Do you have power coming from the starter relay down to the starter solenoid with the key switch in the start position ?
Do you have headlights when you try to crank the engine ?
Have you tried cranking it in neutral ?

Feb 18, 2013 | 1995 Mercury Villager

2 Answers

My 86 f250 was hit and will not start put a new bat and silanoid took starter out to see if it was stuck on flywheel then went to start and all i hear is the fule pump ingage when i turn the key it will...


well i would try turning motor over buy hand if you cant PULL THE PLUGS OUT AND THEN TRY TRUNING MOTOR OVER SEE IF IT IS FULE LOCKE UP IF NOT AND YOU CAN TRUN THE MOTOR OVER BUY HAND STAT LOOKING AT BATTERY CABELS OR BAD GROUNDS HOPE THIS HELPS

Sep 08, 2009 | 1986 Ford F 250

3 Answers

1990 Chevy 1500 4x4 won't engage 4 wheel drive


the 4x4 do not engage in my1990 chevy pick up what i need to check

Jan 24, 2009 | 1992 Chevrolet K1500

Not finding what you are looking for?
1994 Buick Park Avenue Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...