Question about 1995 GMC Yukon

1 Answer

What happens if I disconnect the abs master

What happens if I disconnect the abs master control on a 1995 yokon I did and the brakes work fine can i have a problem down the road , and if I reconnect the plug in and the light stays on could that cause a problem in the future

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Will if the light is on when connected, ABS was nit working, and how it's disconnected and light is off , will you still don't have ABS, it be like a truck that was made without anti-locking bake system.

Posted on Jul 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHY DOES MY ABS AND BRAKE LIGHTS STAY ON?


brake and abs light check brake fluid level. The round float in the master cylinder directly controls the 2 dash lights.
The light is NOT directly controlled by the master cylinder float. The light is controlled by the ABS Module, which location depends on your vehicle. There are a number of different reasons the lights come on. If it comes on but shuts back off within seconds, don't worry about it, that occasionally happens when it gets a bad signal ("nonlatching error"). In rear-wheel-drive (RWD) vehicles, it is common for the differential speed sensor in the rear differential to go bad. You can pick up a Haynes manual to find if you can do at-home diagnostics (Temporarily grounding out the diagnostic lead will cause the ABS light to flash out a pattern indicating the error)


Check the Brake Pressure switch ( also known as SPEED CONTROL DEACTIVATION SWITCH ) which is located below the Brake fluid master cylinder for leakage. The leakage can cause both lights to stay on and also cruise control control not working

Sep 22, 2014 | 1998 Dodge Ram 1500 4WD

1 Answer

1997 chevy 1ton van brake peddle feels like it is pushing my foot back up and i hear a growling sound for about 10 seconds .. i think its the anti-lock brake system but not sure what to check...


yes your right it's abs kicking in , if you look on control moudule next to or just below master cylinder there will be a 2-3 wire plug ,pull it off and see how brakes react DONT TEST THIS ON ROAD ,try it in a safe place at controlled safe speeds if they seam to work fine your abs control module has problems when you do this your ABS light will come on .hope I helped .

Aug 28, 2014 | 1997 Chevrolet C3500

1 Answer

I have a 1995 dodge ram 2500 cummins the abs and brake lights are on and the cruise control is not working? I have replaced the master cylinder and the speed sensor in the rear axle


The warning lights mean there should be a trouble code stored in the body computer. I would start there.
When the ABS system is inop it may prevent the cruise from working too. Sometimes a hydraulic brake system failure will turn the ABS light on too. After repairs you would need to scan the system to turn the light off with most vehicles.
Are the brake lights in the rear of the truck staying on ?

Jul 03, 2012 | 1995 Dodge Ram 2500

1 Answer

No pressure on brake pedal 95 suburban 2500 4x4 7.4L


try bleeding your ABS block first, if that doesn not work could need a master or proportioning vavle. Some scan tools are capable of bleeding the ABS system on some vehicles, and some you have to bleed manually.

Apr 07, 2012 | 1995 Chevrolet Suburban

1 Answer

No fluid at rear brakes on 1995 Olds Cutlass Supreme. I took it into a shop and the code said ABS motor was bad. Would be the cause of no brake fluid coming out when I take banjo fitting off?


Hello
The ABS in this car is what is called Active ABS, so yes a defective ABS Hydraulic control unit motor can cause this problem. Other things that can cause the problem is a defective brake master cylinder or Air trapped in the ABS control unit. You do not say you have done any parts replacement. If this problem did start after any brake system repair then be advised it takes a special tool that electrically holds open the ABS control valves so the air can be removed through bleeding, so if you opened yup the system you must have a shop with the proper tool do the bleeding. There is no way to bleed the brakes at home using conventional brake bleeding means.

Oct 06, 2011 | 1995 Oldsmobile Cutlass Supreme

1 Answer

1995 F350 We pulled a trailer today and after we got a little down the road the ABS light started flashing. When we stopped for gas we could not get the shifter out of park without pulling the #18 fuse....


Well, it could mean that the emergency brake has not been fully released.The ABS system light is on if something has occurred within the ABS system. Something faulty may have happened there, get it checked out!

Aug 05, 2011 | 1995 Ford F350

1 Answer

I have a 1995 jeep wrangler and my front brake calipers have started locking up on me ive put two new calipers on two flexi pipes on two new discs on new master cylinder on one new brake pipe cant think...


Do you have AB? Try disconnecting the harness to the ABS unit if you do, it might give you an idea which direction to go. If not, there must be a kink in a line somewhere.

Jan 07, 2011 | 1995 Jeep Wrangler

1 Answer

I replaced the master cylinder and abs hydraulic control unit in my 1995 chevy lumina. I have good front brakes but can't get any fluid to my back brakes. I even removed the cover from the hydraulic...


Is the ABS light on when the engine is running? You can't bleed this system if the light is on until you fix the problem and "home: it with a scan tool

Aug 26, 2017 | 1995 Chevrolet Lumina

Not finding what you are looking for?
1995 GMC Yukon Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...