Question about 1999 Mercury Sable

1 Answer

How to replace shifter cable 1999 mercury sable

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

Coloumn shifter of center console? unhook from shifter and unhook from trans

Posted on Jul 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove and replace 1993 Mercury Sable LE Automatic gear shifter


I need more info on what it is you need exactly, please explain what is wrong with the shifter, cable broken what?

Jun 27, 2016 | 1993 Mercury Sable

1 Answer

Floor shifter is loose Hard getting into proper gear. How can I tighten it.


Usually, if the shifter is loose, the bushing on either end of the cable is worn out, and the cable must be replaced.

Feb 27, 2016 | 2001 Mercury Sable

1 Answer

What is the cost to replace the frontend ball bearings and calipers on a 1999 Mercury Sable?


wheel bearings are about $75 each calipers about $45 each at most a hr labor for each and thats alot each side could be done in about one hour

Aug 14, 2012 | 1999 Mercury Sable

1 Answer

2000 sable- can't shift out of park. shifter glides and needle on dash moves there's no gears shifting. is the transmission blown?


Not likely a blown transmission. More of a shifter cable issue. There is an adjustment nut on the ****** end. It could be loose or missing. If the nut is fine you have a broken cable.

May 19, 2012 | 2000 Mercury Sable

1 Answer

My Sable will turn on fine but when i try shifting the gear they won't go in the shifter just glides along and the car remains idle. The day it started doing this it made a loud screeching noise and...


If the shifter moves but does not feel like it is trying to put car in gear the cable that goes from the shifter to the transmition could have broke or came loose. If that happened while driving the gears may have tried to shift when tension was released from the cable.

May 10, 2011 | 1999 Mercury Sable

1 Answer

After rebuilding a transmission on 96 mercury sable, car still will down shift to low from drive. Speed odemeter quit working and cruise quit working. Any ideas


Have you tried replacing the speed sensor? Also is your car a column shift or floor shifter? If it is a column shifter make sure to inspect your linkage between the shifter and the tranny.

Feb 10, 2010 | 1996 Mercury Sable

1 Answer

Gears shifter will not engage the gears i think it is the trans linkage where is it located?


it's a cable under car . may be just loose connections. floor shift?

column shift?

check under hood first on driver side where transmision is. look for loose fasteners. then you might have to remove console for floor shift or plastic shrouds if column shift.

Dec 12, 2009 | 1999 Mercury Sable

1 Answer

No diagram for 1999 mercury sable for serpentine


Click on the following free direct Link.
It has the correct Belt Diagrams for your 1999 Mercury Sable 3.0L V6.

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1999/make/mercury/model/sable/1999_mercury_sable_drive_belt_routing_diagram.htm

Nov 07, 2009 | 1999 Mercury Sable

1 Answer

I have a 96 mercury sable when istop it shifts to neutral


it sounds like you need your shifter cable adjusted or replaced or you may have a major motor mount problem that when you decel and acel you are rocking that cable out of postion. but i think it will just take a small adjustment. good luck

Mar 22, 2009 | 1997 Mercury Sable

Not finding what you are looking for?
1999 Mercury Sable Logo

Related Topics:

556 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4376 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...