Question about Cars & Trucks

1 Answer

I just had a rebuilt transmission put in an iam having the same issues with the transmissiion i replaced the speed sensor next cause thats what came up on the computer but the car is still doing the same thing an the speed sensor light still is on an the car still wont shift out of first any ideas?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 661 Answers

If this is a new transmission exhibiting the same dysfunction as the old one then likely there is a problem with either the computer or perhaps the TPS. If the TPS is stuck electrically wide open then the transmission would always think it needed to be downshift. If the tps is good then the computer must be bad because the computer tells the transmission when to shift.

Posted on Jul 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the causes of engine failsafe p in Bmw x5 2006 model


The reason is the engine speed and transmission speed sensors don't agree. It could be caused by a bad transmission speed sensor, bad transmission fluid, a failed solenoid in the valve body ( in the transmission pan), a worn out valve body, a bad transmission, improper tires(that don't match each other), a faulty MAP sensor (air flow sensor on the air intake), faulty engine speed sensor and possibly a few other things.

Get the codes with a reader, and it might direct you in the right direction. But take the reading with a grain of salt, because it rarely tells you the exact problem. My fail safe came on and the code was TCC solenoid, but after replacing that, I had to install a rebuilt valve body to solve the problem.

Jan 14, 2016 | BMW Cars & Trucks

1 Answer

1996 dodge grand caravan shifts down into first when coming to a stop.After it has been drivin for a min.Stays in first gear after it slams into first from second.


It's actually putting itself into second gear. Chrysler A-604 transmissions are an electronically controlled transmission which use speed sensor to see things like vehicle speed, engine rpm, throttle position and internal transmission component speeds. It can determine if there is an issue with the transmission based on these sensors and when it does it tells the transmission to go into "limp mode" which is basically just second gear. This would allow the driver to move off the highway to the side of the road or drive it slowly for a while to a service facility. To determine the exact issue with the transmission you need to go to a shop that can read the transmission codes and decipher whether the transmission can be repaired in the vehicle or must be removed and rebuilt. It is common to have a sensor fail and cause this issue which means a reasonably low cost repair. It is also common for the trans to need complete overhaul. It IS worth it to go to a "qualified" transmission repair garage though so it can be properly diagnosed.

Good luck and hope this helps.

P.S. Did you check the fluid level first, idling in park? Had to ask.

Jun 12, 2014 | 2002 Dodge Caravan

1 Answer

Espesific location of turbine speed sensor on transmission 1998 cadilac deville


their is no such thing as a turbine speed sensor ,as in the torque converter ,you measure the speed of this from the RPM of the engine their is no other sensor that iam aware off ,the next sensor is the road speed sensor or mph sensor which would be on the passenger side transmission shaft drive just on top right by the differential .Their is no sensor measuring the gearbox side of the torque converter speed as it will be the same as the RPM but allowing for slip which is why the torque converter is their in the first place and their is a specific graph for this sort of information with variables for vehicle weight /power /gear ratio /load .

Mar 11, 2011 | 1998 Cadillac DeVille

2 Answers

AWD Disable and abs light always come on , already replaced rear selanoid . Whats going?


CHECK ABS FUSE AND RELAY.THE AWD CONTROLED BY SPEED SENSORS ONE IN THE FRONT OUT PUT SHAFT SECOND SPEED SENSOR IN THE REAR OUT PUT SHAFT THIRD SPEED SENSOR IS VECHICLE SPEED SENSOR.BEST TO HAVE VECHICLE FIX AT A GARAGE OR DEALERSHIP YOU WILL NEED DIAGNOSTIC EQUIPMENT TO WORK ON IT.

Aug 30, 2010 | 2002 Buick Rendezvous

1 Answer

1994 Ford E350 transmission seems like it slips at 45-55 MPH.


If you went 1k miles since that same issue occurred I would look at the transmission. A faulty torque converter, clogged fuel filter, or a clogged CAT can cause a delay in the shifting but it would happen right away not 1k miles later.

May 05, 2010 | 1994 Ford Econoline

2 Answers

02 mercedes clk430 stuck in limp mode. Transmission has been rebuilt, we have no power to the speed sensor, we changed the connector plate and the car is still in limp mode what can be wrong? all fuses are...


HI

Since you have rebuilt the transmission it is suggested to replace the speed sensor,this is the cause that your car is stuck in limp mode.

Let us know if you want to know somethin more else accept the suggestion.

Thanks for contacting fixya.com

Apr 27, 2010 | 2001 Mercedes-Benz CLK-Class

2 Answers

Recently changed my engine,now the transmission,not changing gears or shifting properly


Check your wire harness to the transmission located on the drivers side under the battery, look for any damaged or disconnected wire harness and also inspect the wire leads to the harness at your TCM (transmission control module) located on the passenger side fender. Check the fuse to your TCM and don't forget to check the fuses under the dash on the drivers side, replace any fuse that has gone bad.
Good luck and hope this helps, 85% of the time it's going to be a electrical issue that causes your transmission not shift properly. The other causes for your transmission issues are: TPS sensor and the input speed sensor and out put speed sensor in your transmission.
Thank you for using Fixya and start with the simple and check the fuses and wire harness. Good luck

Mar 29, 2010 | 1996 Dodge Caravan

1 Answer

1989 nissan pathfinder transmission issure


time for a new/rebuilt computer for your 1 gear issue sounds like a few stripped gears or synchronization issue in the transmission you need to take your truck to a transmission repair shop get the sensor checked and sync bar checked for any broken pieces and metal shavings may also need to replace you slave cylinder make sure it goes in and out have someone sit in car and press clutch in you get under the front and look before clutch assembly for little black bar that is going in and out

Apr 22, 2009 | 1988 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

john h

Level 3 Expert

17852 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...