Question about 2002 Isuzu Trooper

1 Answer

Is the oil pan drain plug located under the ground skid plate on a 3.5 trooper 4x4 2002. Is there a drain plug on the automatic transmission same vehicle or is it a sealed transmission?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,098 Answers

Hi

Do you know which gearbox it is? some are GM and some BMW I know that sounds crazy but this model has 2 types of gearbox neither made by Izusi. Look here at this diagram tell me if that is the correct box http://www.unofficialbmw.com/images/BMW_Automatic_4L30E.pdf

get back to me if not and I will be able to locate for you.

Regards
Dan

Posted on Jul 22, 2010

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change my oil?


Remove filler cap,
lift car
then from under the car remove oil pan drain plug.
Allow oil to drain into an oil waste pan.
Change oil filter also ..located under skid plate..use filter wrench to remove filter. Be careful as filter is full of oil ..drain in waste pan
wipe filter mounting plate clean..put a thin coating of oil on new filter gasket before spinning it on to the mounting plate..hand tighten and then tighten about 3/4 more turn.. reinstall drain plug. do not over tighten or you can strip the threads. Install correct viscosity and amount of oil start engine. let run to get pressure up. shut off engine, check level with dipstick and close cap....you are done.

Feb 12, 2015 | 2010 Nissan Frontier

1 Answer

How to change gearbox oil


gear + BOX
so is the transfer case, box. or the 5 speed stick box or?
what?
we drain it then fill it, to the mark.
on all gear boxes.
if A/T we RTM read the operators guide. for how to do it right,
most dont and wreck the tranny. the #1 reason they removed the filler.
when posting car issues, stated what it is.
like this.
95 Trooper, 4wd M/T , i want to change the 5speed box lube.
what do i need to do that.?
ill spin the wheel of fate, and land on 5speed box.
and answer for TR5 and NV1500 boxes.

For all transmissions except for the Borg-Warner T5R, replace the transmission fluid at the first 15,000 miles (24,000 km) and then every 30,000 miles (48,000 km) thereafter. The Borg-Warner T5R transmission does not require periodic changing of the transmission fluid. (they lie)
  1. Raise the vehicle and support safely on jack-stands. Place a fluid catch pan under the transmission drain plug.
  2. Remove the fill plug from the side of the transmission, then remove the drain plug. Be cautious when removing the drain plug: the transmission fluid can be very hot. Allow the transmission fluid to drain into the pan.
  3. Install the drain plug and tighten to 20 ft. lbs. (27 Nm) for all models except the 1996 Hombre, which requires 27 ft. lbs. (37 Nm).
  4. Refer to the manual transmission fluid recommendations for the proper viscosity of engine oil, or type of transmission fluid to be used for the T5R and NV1500 transmissions. Fill the transmission by pouring the new fluid through the fill plug hole in the side of the transmission. Fill until the fluid starts to dribble out of the filler hole. Install the fill plug to 17 ft. lbs. (23 Nm), then lower the vehicle.
so next you ask, what fluid
sure.
Use engine oil for all of the manual transmissions, except for the Borg-Warner T5R and the NV1500 (1996 Hombre). Make sure to use engine oil of the correct viscosity for these transmissions, as follows:
  • Except 1992-96 Rodeo and Trooper, high temperature-SAE 40
  • Except 1992-96 Rodeo and Trooper, normal temperature-SAE 5W-30SF
  • 1992-96 Rodeo and Trooper, high temperature-SAE 15W-40, 20W-40 or 20W-50
  • 1992-96 Rodeo and Trooper, normal temperature-SAE 5W-30
he Borg-Warner (B-W) T5R is found on Rodeo models with the V6 engine. The 1991-93 B-W T5R uses DEXRON-II automatic transmission fluid, whereas the 1994-96 B-W transmission uses DEXRON- III automatic transmission fluid.

use the highest Dexron number, on the shelf, mark III is not made today.

Jul 03, 2014 | 1995 Isuzu Trooper

1 Answer

98 isuzu trooper leaks a/t fluid


No, but take rags and wipe off all the oil. Leave the skid plates off for the time being. Use jack stands or blocks to raise car so you can be under it. You need to run the engine so the transmission pump is working, then you will probably see where the oil is leaking from-possibly the pan gasket, maybe that component on the oil pan, or check if it is coming from higher up and collecting on the pan. Hope you find it. Pan gaskets are very easy to change. But you will have to replace the transmission fluid, as about 6-8 quarts will drain when you remove the pan. If you have to change the gasket, might as well change the transm. fluid filter as well-it's right underneath the pan, in most cases.

Feb 10, 2013 | 1998 Isuzu Trooper

1 Answer

How to replace oil pan


5.2 liter V8 engine?

Remove the four front skid-plate bolts holding the front skid plate, using a ratchet and socket. Remove the skid plate.

Pull the plastic splash shield away from the vehicle, loosening the retaining clips. Remove the splash shield.


  • Place an oil drain container under the oil pan. Loosen the drain fitting with a wrench until oil drains from the pan. When oil is done draining, tighten the drain fitting.

  • Disconnect the electrical connections running to the starter motor. Remove the starter motor mounting bolts with a ratchet and socket, then remove the starter motor.
  • Remove the oxygen sensor socket from the exhaust pipe, using a wrench.
  • Remove the exhaust manifold bolts where the exhaust meets the manifold on both sides, using a ratchet and socket
  • Place an jack under the transmission to support it. Remove the pressure on the transmission crossmember.

  • Remove the bolts that hold the transmission crossmember in place, using a ratchet and socket. Then remove the crossmember. Place a jack stand under the transmission to keep the transmission from falling off the jack if hit. Once removed, the exhaust will hang down, allowing enough room to remove the oil pan.
  • Disconnect the oil level sensor and the nut retaining the transmission cooling lines, using a wrench.
  • Remove the oil pan bolts with a ratchet and socket, then remove the oil pan and gasket.
  • Clean the mounting surfaces of the new oil pan and engine block. Make sure what ever you use to clean the surfaces dosn't gouge the metal.
  • Place a coat of RTV (gasket) sealer on the engine block where the pan will meet the rear main cap.
  • Place the new gasket on the pan and push the new oil pan into place. Finger tighten the oil pan mounting bolts to hold it in place. Tighten the bolts with a torque wrench to 18 ft-lbs. DO NOT OVER TIGHTEN THE BOLTS! Doing so will cause the gasket to deform and create leaks!

  • Connect the oil level sensor and the nut retaining the transmission cooling lines, using a wrench.
  • Place the exhaust back into position and replace the transmission crossmember bolts and crossmember with a ratchet and socket.
  • Remove the jack supporting the transmission.
  • Connect the exhaust back to both sides of the manifold, tightening the bolts with a torque wrench to 20 ft-lbs.
  • Attach the oxygen sensor socket to the exhaust pipe with a wrench.

  • Replace the starter motor by installing the starter motor mounting bolts with a ratchet and socket. Connect the electrical connections to the starter motor that were disconnected during removal.
  • Push the retaining clips on the plastic splash shield into the appropriate retaining clip holes.
  • Replace the front skid plate by replacing the four front skid plate bolts with a ratchet and socket.
  • Fill the engine with 5 quarts of oil. Make sure to check the level on the dipstick to find the exact level when filling.


  • Jun 28, 2012 | 1997 Jeep Grand Cherokee

    2 Answers

    I'd like to do an oil change on my trailblazer 04' but i cant find the drain plug,,,,where is it? Is there a guard i have to remove?


    Hello,

    The drain plug of the chevrolet 2004 trial blazer is located under the engine skid plate it is with the oil filter. And there is a guard to be removed. There is a trap door before it.

    The skid plate door is located by the drivers side door, directly midway underneath the vehicle. You will need a flat/phillips hear screwdriver to open the trap door. Do not worry, the screws are 'loss-proff' and will not fall off the trap door plate. Once this has been removed, the oil drain plug and oil filter are now visible and accessible.

    Oil change should not take you more that 15/20 minutes.

    Hope this helped.
    Take care and good luck

    Jan 03, 2011 | 2004 Chevrolet TrailBlazer

    1 Answer

    Can't find oil drain plug on my 2003 kia sorento


    it is located under the skid plate under the engine. there are two screws in the front under the radiator, two on the side, and two under the transmission. Once you take the plate off you will see the oil pan and plug

    Nov 14, 2010 | 2003 Kia Sorento

    2 Answers

    Where is the oil pan drain plug on a 2005 sunfire


    A 2003-05 Sunfire most likely has the Ecotec 2.2 motor. The filter is a cartridge element type which is located on the forward side of the engine on the drivers side; (below and slightly left of the power steering reservoir).

    The oil filter is located under (inside) a black cover about 3-4 inches around and has a large hex head nut molded on top of it, to fit a socket on it. When replacing the oil filter element, press the tipped O-ring side of the filter down into the filter cavity until it locks in place. Then place the cover on top and tighten it.

    The cover will automatically lock onto the top section of the oil element as it is being tightened. The drain plug is pretty standard and on the oil pan. However, most people are accustomed to a metal oil pan, and when viewing the Ecotec motor they confuse the metal TRANSMISSION pan as the motor oil pan.

    The motor oil pan is actually aluminum, and looks like a continuation of the upper motor. For that reason, you don't "see" an oil pan. Knowing this fact, the oil drain plug is now easy to locate. Look at the far passenger side of the metal transmission oil pan. Now look at the very front of that section of the transmission oil pan and follow that ''line of sight'' until you reach the bottom of the aluminum motor (''oil pan''). The oil drain plug is right there, with it's head facing towards the transmission oil pan.

    The drain plug (on a 2005 Sunfire) requires a 15mm wrench/socket; and has a built in rubber seal, which should be lubricated with oil before tightening.

    Sep 18, 2010 | 2005 Pontiac Sunfire

    1 Answer

    Another question, is the drain plug for the oil pan under the skid plate so i can change the oil myself? 2002 VW bug 2.0 motor Thanks, Matt


    hi, yes you need to remove this plastic skid plate then this will give you access to the oil drain plug.

    Let me know how you get on or if you need further assistance ok

    Feb 01, 2010 | 2002 Volkswagen Beetle Turbo S

    2 Answers

    2001 audi a4


    Transmision oil for 2001 Audi A4 1.8 l turbo:
    Manual gearbox (5 speed):
    - Capacity = 2,25 liters
    - Specification: Gear oil SAE 75 W 90 (synthetic oil)
    Part number G 052 145 S2 (1 liter)
    - To check oil level, unscrew oil filler plug placed on the left side of the gearbox in front and near of transmission axle, using an Allen 17 mm key.
    - Check oil level with locally manufactured tool, e.g. a piece of angled wire.
    - Specification: oil level 7 mm below bottom edge of oil filler hole.
    - Install oil filler plug, tightening torque = 25 Nm.
    Please Rate my Response! Thanks!

    Sep 27, 2009 | 2004 Audi A4

    1 Answer

    Where is the transmission fill plug located on a isuzi trooper


    On the transmission pan. Lower one is a drain the upper one is the fill level plug. Crank up the engine and let it idle for 3 minutes. Then remove the upper plug, if none comes out squirt some in if some comes out let it drain until it stops. This is the upper plug, not the lower one.

    Aug 08, 2009 | 2002 Isuzu Trooper

    Not finding what you are looking for?
    2002 Isuzu Trooper Logo

    255 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Isuzu Experts

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14398 Answers

    Are you an Isuzu Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...