Question about 2000 Mercury Mountaineer

1 Answer

How do i remove rear brake caliper on a 2002

I have removed the two 10mm bolts that hold the but I can not seem to find any other bolts that keep the caliper bolted to the car. what could I be missing?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

Nothing. On the front disk there are only two bolts that hold the caliper in place. Once they are all the way out it is just a matter of wiggling and pressure to remove the caliper. The rear calipers are also held on with 2 bolts but because of the way the brake line attaches you also have to remove that to remove the caliper.

Posted on Jul 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear brakes on 2011 kia sorento


You will likely find there are two bolts holding the calipers on the 2011 Kia Sorento. You can check this by parking your Sorento, setting the parking brake to be sure it won't roll and carefully lifting and removing one of the rear wheels, just like you are removing a flat.

When you remove the wheel, you should find that the brake caliper carrier is accessible on the rear top of the wheel assembly. Simply reach around and carefully feel the carrier assembly and you should feel a couple of bolt heads because two bolts are generally used to hold down Kia rear calipers.

Jan 03, 2015 | 2011 Kia Sorento

1 Answer

Replace rear brake discs and pads


Depending on vehicle. Find level ground and park there. Put chocks in front and behind wheels not being lifted. Loosen lugs, jack up vehicle, set jack stands, lower vehicle on jack stands, remove lugs and wheel. Open hood remove brake fluid cap. Remove two bolts holding caliper, pull caliper off rotor disc and bracket, remove pads, place a used pad in front of caliper piston, use a c clamp to push caliper piston in caliper, remove c clamp and old pad, hang caliper up, remove 2 bolts holding caliper bracket, remove bracket, remove rotor, install new rotor, install caliper bracket, install new pads, install caliper, repeat this on other side, put cap back on brake fluid tank, remove bleeder fittings and keep pressing brake pedal until an even flow of brake fluid sprays out. Install bleeder fitting. Make sure brake fluid doesnt get on paint and is contained and disposed of correctly, top off fluid install wheels and raise car up remove jack stands, lower car and break in new pads

Nov 06, 2013 | Cars & Trucks

2 Answers

How do i remove rear roters off a ford e250


you must remove the brake caliper and the brakes next the bracket that was holding the caliper must be removed there are two big bolts holding it on once that is removed use a hammer and tap the rotor off when you replace the rotor use never seize and the two big bolts shood be lock tight you can pick up never seize and lock tight ( blue) hope this helps good luck

Apr 23, 2011 | 2003 Ford E250

1 Answer

Remove rear brake disc


Remove the two bolts that hold the brake caliper on, remove the brake caliper, pull the brake rotor off. Opposite for assembly.

Feb 09, 2011 | 2002 Ford Explorer

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

Need to replace rear brake discs and pads


YOU NEED TO REMOVE THE REAR WHEELS.REMOVE PARKING BRAKE CABLE CLIP FROM CALIPER DISCONNECT PARKING BRAKE CABLE.HOLD THE GUIDE PIN WITH A BACK UP WRENCH AND REMOVE UPPER MOUNTING BOLT FROM THE BRAKE CALIPER.SWING THE CALIPER DOWNWARD AND REMOVE THE BRAKE PADS.TO INSTALL NEW PADS.YOU HAVE TO RETRACT PISTON INTO THE HOUSING BY ROTATING THE PISTON CLOCKWISE.PUT EVERYTHING BACK VISA VERSA.

Feb 24, 2010 | 2002 Jaguar X-Type

3 Answers

How do i remove the rear rotor on a 2000 ford explorer xlt


  1. Disconnect the brake hose.
  2. Remove bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  5. Disconnect the brake hose.
    1. Remove bolt.
    1. Disconnect the rear wheel brake hose (2A442).
    1. Remove the copper washers and plug the brake hose.
      syn~us~en~file=dh0472a.gif~gen~ref.gif
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
      Remove the rear disc brake caliper (2552).
      1. Remove the brake caliper bolts (2W303).
      1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
      syn~us~en~file=gh0619a.gif~gen~ref.gif
    1. Inspect the rear disc brake caliper for leaks.
      • If leaks are found, disassembly is required. Refer to Caliper in this section.
      syn~us~en~file=gh1478a.gif~gen~ref.gif
    Installation
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
      NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
      NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
      Install the rear disc brake caliper.
      syn~us~en~file=dh0528a.gif~gen~ref.gif
    1. Install the rear wheel brake hose.
      • Connect the brake hose and install the caliper flow bolt.
        • Use new copper washers.
      syn~us~en~file=gh0621a.gif~gen~ref.gif
    1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
    1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
      Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
    1. Verify correct brake operation.
  6. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
--------------------------------
Installation
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
    Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

May 06, 2009 | 2000 Ford Explorer

2 Answers

2002 Pontiac Grandam, Rear Brake Pad Change


no 10mm or 12mm you will also need a ebrake caliper reset tool

May 29, 2008 | 2002 Pontiac Grand Am

Not finding what you are looking for?
2000 Mercury Mountaineer Logo

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

fordexpert

Level 3 Expert

5626 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...