Question about 2006 Dodge Ram 1500

1 Answer

Low beams not working on 2006 dodge ram truck. Tested and both lights not getting any power. Can't find a fuse anywhere for them ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,826 Answers

I check for fuses under the hood in a box.


Low beams not working on - prev.gif next.gif Fuses dod_ram15_02-04_fuse1.gif



dod_ram15_02-04_fuse3.gif
---
I found relays in the box for the parking and driver lamps, but not the low beams.

I would check the color of the wires leading to the low beams and try to match it up with the tables I sent you under 'circuit' column.
---
Circuit Breakers dod_ram_02-04_circuit_break.gif
prev.gif next.gif --Low beams not working on - dod_ram15_02-04_ipm.gifModule dod_ram15_02-04_ipm.gif

The integrated power module combines the power distribution center and the front control module. It is located in the engine compartment next to the battery.
---
Finally, I conclude the following may be the problem:
Removal & Installation To Remove:

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • LefLow beams not working on - dod_trk_headlampsw.gifel
    • Harness connector dod_trk_headlampsw.gif

    • Headlamp switch from the instrument panel bezel with the screws
To Install:
  1. Install or connect the following:
    • Headlamp switch to instrument panel bezel with the screws
      1. Torque to: 20 inch lbs. (2.2 Nm)
    • Wire harness connector
    • Left instrument panel bezel
    • Negative battery cable
-------------------------------------------------------------------------------------------prev.gif next.gif Good luck on this repair.

Posted on Jul 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the low headlights fues on 2006 Dodge Ram 2500


Most headlight fuses are next to the battery, but some low beams are incorporated into the daytime running lights. Check the relay too for a signal from the dash switch and check for constant power side of relay also. One side is main power that gets relayed to the low beams and the other part of the relay is the side that gets the signal from the dash switch, one side is ground and the other is power, but the dash switch needs to be on headlights to diagnose.

Mar 05, 2016 | Dodge Cars & Trucks

1 Answer

2006 dodge ram 2500


check the tipm module for high beam driver may be bad

Oct 11, 2013 | 2006 Dodge Ram 2500

1 Answer

1996 dodge Ram 1500 4x4 headlights dont work.All other lights work. Headlight lamps are all good. Could it be the switch or the multifunction switch? High beam works when I pull on the directional le


The headlight switch gets power for the headlights from a 50amp fuse.
The fuse powers the headlight switch then the dimmer switch breaks for high and low beams. So if the high beams work, the problem may be with the dimmer switch.
The dimmer switch is made into the turn signal switch on the column. You would need to check the low and high beam circuits at the switch for power.

Jan 14, 2013 | Dodge Pickup Cars & Trucks

2 Answers

Dodge ram 3500 turn signal - headlight problem


WAY TO GO !!! another "great idea" from vehicle manufactures

Jun 07, 2012 | 2004 Dodge Ram 3500 Truck

2 Answers

High beams work but not the low beam lights


check relay!!!!!!!!!!!!!under hood in relay//fuse cluster,cheers

Dec 23, 2009 | 2006 Dodge Ram 2500

1 Answer

2006 Dodge Ram 3500 diesel 4x4.I want to install four KC Rally 800 HID lights on my truck. I would like all 4 lights to go off when I switch to low beam. The lights will be on relays and rocker switches...


I cant tell you off the top of my head, but the easiest way is as follows.

Turn on your low beams, with a test light or volt meter, find the wire that powers the low beams (it will lose power when you switch to high beam).
Once you have found that wire, wire the lights and relays as if the hot low beam wire is your "switch", it will supply the switch power source the 12v it needs to turn on the power to the lights.

Hope this helps ya out.

Nov 08, 2009 | 2006 Dodge Ram 3500 Truck

5 Answers

I have no headlights!! parking lights, taillights,and blinkers all work fine. none of my fuses or bulbs are blown


I have a 2004 ram 2500 and all my lights work except for low beams. It is not in the switch, I haver replaced the switch with no change. This is a circuit problem with these dodge pickups. I haven't firgured out what it is but it isn't the switch. and unless the low beams and high beams are fused seperate, it isn't a fuse problem either. i have looked for a fuse and can't even find the fuse for the headlights. Im lost like you!

Jun 15, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Headlights not working


check fuses in under hood fuse box let me know i will at some diagrams for you hey vote for me ok

May 26, 2009 | 2006 Dodge Ram 2500

1 Answer

Left low beam is out on my 2006 dodge ram 1500 4.7 v8 the bulb isnt blown and the high beam works low beam does not


I'd still vote for the bulb being bad. The high and low beams use two different filaments, so unless the bulb is physically broken, it is common for the low beam to be bad whilst the high beam is good.

That's why you see some people driving around with their high beams on -- they don't want to get stopped for a 'light out' citation..

When you take the bulb out to replace it, be sure to look at how it is mounted before removing. You don't want to accidently adjust your headling out of kilter.

good luck

Apr 06, 2009 | 2006 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

499 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...