Question about 2000 Ford Focus

1 Answer

Hanger bearing needs to be replaced and a axle bearing

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

The carrier bearing for the axle will come with new 1/2 shaft.

Posted on Jul 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

AFTER REPLACING U-JOINTS & HANGER BEARING ON MY 1995 VOLVO 960 I HAVE VIBRATION AT SPEED PARTICULARLY UNDER ACCELERATION. I TRIED ANOTHER SHAFT AND IS WORSE. I THINK IT MIGHT BE HANGER BEARING ALI


did you mark the two ends of the shaft at gearbox and diff
so they lined up again
with the center bearing replacement
did you mark the two halves before separating and replacing the center bearing
then make sure they lined up again

if vibration is there
you may need to go to a diff shop and have the drive shaft balanced properly

very informed drive shaft write up.. on volvos
Driveshaft Rear AxleDriveline Rear Axle
26328039-dr1l0prezoqh0gobrdoiolxi-5-0.jpg

Oct 26, 2016 | Volvo Cars & Trucks

1 Answer

How to replace a hanger bearing in a 2002 gmc sonoma


I\'ve never heard of hanger bearing. Where is it located. Are you talking about the carrier bearing. The carrier bearing is somewhat of pain if you don\'t have the right tools. If it\'s the carrier bearing your talking about you need to rent or buy a bearing puller and hopefully you have air impact but it\'s still possible without. Well let me know where this bearing is and i can help you out more.

Apr 21, 2014 | 2002 GMC Sonoma Extended Cab

1 Answer

How to replace a hanger bearing on a G20 CHEVY VAN


It is pressed in in, but most just replace the entire center support assembly it is allot easier.

Jun 27, 2012 | Cars & Trucks

1 Answer

How replace front wheel bearing


remove wheel,brakes,an caliper hanger the hard part is to remove the king nut or axle nut after u get that remove bolts on back of spendle remove hub or bearing assembly replacewith new one repeat steps in reverse

Dec 20, 2010 | 1996 Toyota Celica

1 Answer

Hanger bearing needs to be replaced and a axle bearingso they say what kind of money are we looking at and is this common?


The axle bearing /wheel bearing if thats what they mean runs about $200.00parts and labor. I'm at a lose on the hanger bearing, what is it , do you know where it is located

Jun 17, 2010 | 2000 Ford Focus

1 Answer

The axle pops out on my 98 ford contor


If its the passenger side axle then the hanger bearing retainer may be missing the bolts, or rusted out and not holding it in place. Check ! Make sure that the outer shafts are not missing the nuts that hold them to the wheel, and check your lower ball joints for integrity.

Jan 28, 2010 | 1998 Ford Contour

2 Answers

Need direction on replacing the front hub assembly on the front passenger side


It's a press-in bearing. If you don't have the tools to press the bearing, you can still save some money. Here's what I did:
- Drain transmission oil,
- Remove front right wheel,
- Remove brake caliper, pads, caliper hanger,
- Remove the wheel speed sensor (even if no ABS),
- Remove the two large strut bolts (100+ lbs ft/lbs of torque),
- Remove the ball joint nut,
- Remove the ball joint from the steering knuckle,
- Remove the axle from the transmission using a pry bar.

Now you'll have the axle, steering knuckle, wheel hub and brake rotor removed from the car, and it'll all be ceased together. Bring the whole thing to your favorite mechanic and get him to separate all these parts and to install the new bearing in the steering knuckle. It'll cost about $100.

Now you'll have the axle, steering knuckle with new bearing and hub installed, and the brake rotor. Take these parts home and put the car back together in reverse order.

Seriously consider replacing the axle while you're at it.

Nov 17, 2009 | 2003 Hyundai Tiburon

2 Answers

How to a Change the Driver Side Wheel Breaing? 93 Toyota Corolla


need to take wheel off and take the 3 or4 bolts out of bearing also may need to take axle nut off should come off with ahammer.

Jan 01, 2009 | 1993 Toyota Corolla

Not finding what you are looking for?
2000 Ford Focus Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...