Question about 1999 Isuzu Trooper
You just put it in where the dipstick is.behind the oil dipstick.
Posted on Aug 22, 2010
At transmission pan, there will be two drain plugs, the up most drain plug is where you fill it and check level, to check level, with engine running and in park, unscrew up most plug on transmission pan, if fluid come's out, level is good, if no fluid come's out need to add transmission fluid in that drain plug.
Posted on Jul 22, 2010
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
NOT SURE IF IT IS TRUE ON THIS KIND OF VEHICLE, BUT USUALLY WHEN CHANGING A BULB YOU NEED TO GO UNDER THE HOOD ON WHATEVER SIDE YOU ARE CHANGING...AND THERE WILL BE A KIND OF PLUG INTO THE BACK OF THE ACTUAL LIGHT FIXTURE, IF YOU GIVE IT LIKE A QUARTER TURN IT WILL PULL OUT YOU THEN CHANGE THE BULB AND PROCEED WITH PLUGGING BACK IN. MAYBE THIS WILL HELP!
Posted on Jan 10, 2009
If your car is over-heating, chances are it's the water pump or
thermostat. These two parts should be changed out at the same time
because if your pump is old enough to go out then the thermostat is not
Step1 First you'll need to pull out the old water pump. Look in your vehicles owners manual and find the diagram showing what all that stuff under your hood is. locate the water pump (usually underneath alternator running on the same belt) you'll need to take this belt (serpentine or other) off to start pulling the old pump. There should be a tension bar or arm that easily loosens the belt with the right size socket. Step2 Once you've gotten the belt off you can begin to remove the old pump. There should be only a few large bolts holding it in. After you've gotten the old pump out, place the silicone sealer on the new water pump 9around the edges where it meets the gasket. Then apply the sealer to the gasket as well, just use your fingers to spread it on. Now place the new pump with gasket, where the old one was, replace the bolts and be sure not to crank down too tight on the bolts or you might crack the gasket and your pump wont seal. Step3 Now that you've gotten the new pump installed, you'll want to replace the thermostat. the thermostat could be located near the water pump or on the other side of the engine. So once again, refer to the vehicles owners manual and find where the thermostat is. You might need to remove some hoses and/or lines to get to the thermostat, so just be careful not to break/bend/crack or damage anything (the older the vehicle, the better chance of something breaking) Pull the old thermostat and replace it with the new and you're all done. Don't forget to put everything (hoses, lines, nuts'n bolts) back where they came from and off you go!
Posted on Mar 20, 2009
SOURCE: I NEED PUT TRANSMISSION OIL
there is a plug in the pan, with engine running , fluid should barely come out, if not, its low and you will need to "pump" it in, a repair shop may be best to check the fluid level.
Posted on Dec 26, 2010
Tips for a great answer:
Jun 08, 2014 | 1991 Isuzu Trooper
Oct 01, 2013 | 1999 Isuzu Trooper
Mar 05, 2013 | 2002 Isuzu Trooper
Jul 13, 2012 | 1996 Isuzu Trooper
Mar 17, 2011 | 1996 Isuzu Trooper
Feb 09, 2011 | 2001 Isuzu Rodeo
Jun 09, 2010 | 1989 Isuzu Trooper
May 08, 2014 | 1999 Isuzu Trooper
261 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: