Question about 2000 Jeep Grand Cherokee

1 Answer

When I start the vehicle, there are several beeps and then ''Perform Service'' is displayed for a few seconds on the screen (then goes off). The car didn't come with a manual so I'm not sure what type of service is needed. Can someone help and let me know?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 106 Answers

This is a "reminder" chime to let you know to change the oil. It is set to chime after reset and 3000 miles. It is not connected to the condition of oil, just a timer. When it goes off again just hit the reset button. Probably need to change your oil and then hit the reset button.

Posted on Jul 22, 2010

Testimonial: "Thank You!"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do I have an intermittent problem with ABS and power steering lights?


Bad or loose intermittent wire connections to and from sensors. Some unauthorised mechanic has been working on the car? Take it back and talk to the service manager, or the shop owner.

Apr 14, 2015 | 2010 Volkswagen Polo 1.2

1 Answer

Why is there a beeping noise every 5 minutes or so while driving-


AS LONG AS YOUR CAR IS RUNNING FINE & HAS BEEN SERVICED RECENTLY YOU CAN ALTER THIS MESSAGE ON SCREEN TO STOP THE BEEPING, THE EASIEST WAY IS TO DISCONNECT BOTH THE + & - BATTERY LEADS & CONNECT THEM TOGETHER FOR AT LEAST 30 MINS, THIS WILL RESET THE JEEP'S MEMORY, CONNECT BACK THE LEADS & THEN WHEN YOU GET IN & START YOUR CAR THE DISPLAY BY THE GEARSHIFT WILL BE FLASHING - SET THE CLOCK BY KEEPING YOUR FINGER ON THE SET BUTTON FOR S FEW SECONDS UNTIL THE IST DIGIT BEGINS TO FLASH, THEN PRESS THE SET BUTTON UNTIL YOU REACH THE DESIRED HOUR, THEN PRESS THE SELECT BUTTON BELOW & THIS WILL MOVE YOU ON TO THE MINUTES, CONTINUE WITH THE ABOVE OPERATION UNTIL THE TIME & DATE HAVE BEEN SET, YOUR "SERVICE" SHOULD NOW BE RESET TO EITHER 7500 MILES OR 12500 MILES, I SERVICE MY 96 GRAND CHEROKEE MYSELF SO THIS IS MY "CHEAT" FOR THE SYSTEM & IT IS GUARANTEED TO WORK. BEST OF LUCK.

Sep 05, 2012 | 1995 Jeep Grand Cherokee

3 Answers

I have a 2002 Chevy Venture and am having problems with the ignition. Our master was damaged so we got a new pk3 transponder key cut and tried to program it but it still won't work. We did the turn it...


You do not have another master ? If not you need a factory scan tool Dealer or mobile lock smith .
Connect a scan tool to the vehicle.
Turn ON the ignition, with the engine OFF.
Insure that all power consuming devices are turned OFF on the vehicle.
With a scan tool, select Request Info. under Service Programming System and follow the scan tool on-screen instructions.
Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions.
Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
With a master passkey III key, turn ON the ignition with the engine OFF.
With a scan tool, select Program ECU under Service Programming System.
At this point the scan tool must remain connected for the duration of the 10-minute relearn procedure.
Important: On some vehicles the SECURITY telltale maybe illuminated on steady for the duration of the 10-minute relearn procedure.
Observe the scan tool, after approximately 10 minutes the scan tool will display "Programming Successful, Turn OFF Ignition". The vehicle is now ready to relearn the key information and/or the passwords on the next ignition switch transition from OFF to ON.
Turn OFF the ignition and wait 5 seconds.
With a master Passkey III key, start the vehicle. The theft deterrent control module has now learned the key transponder information and the PCM has now learned the fuel continue password.
Important: Perform this step ONLY on vehicles with EXPORT and Canadian configured theft deterrent control modules.
Turn OFF the ignition and wait 15 seconds minimum.
Important: Perform this step ONLY on vehicles with EXPORT and Canadian configured theft deterrent control modules.
With a second master passkey III key, start the vehicle. The theft deterrent control module has now learned the second master Passkey III key transponder information
With a scan tool, clear any DTCs.

Nov 20, 2017 | Chevrolet Venture Cars & Trucks

1 Answer

On my 2000 jeep grand cherokee information center is displaying perform service i would like to know what i have to do to fix it


The perform service message tells you when you need to change oil. To reset it turn the key on and press the step button until miles to service is displayed (it should say 0 underneath). Then press and hold the reset button until it changes from 0 to 3,000 miles. Then start the vehicle. The message should no longer be displayed.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

May 27, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I get a message "service 4 wheel drive switch" it


You need to replace the computer for the display. I found one at the local junk yard cost me $30.00 and fixed the problem. It is the display screen computer.

Dec 29, 2010 | 1994 Jeep Grand Cherokee

2 Answers

Perform service jeep grand cherokee 2005 this message is appearing in the message center


Actually the newer cherokees are a little more complicated, it's not a reminder for an oil change. It is for an emssions service that should be performed according to the dealer. Here is the rest procedure

Turn ignition to on position, but do not start.
Depress brake pedal fully twice.
depress excellerator very slowly twice
Turn ignition off & that will reset the perform service indicator.
I am mechanic & we are getting frustrated because the dealers do not want to release this info to anyone, they want your money! Can you believe if you did not get them to perform the service they charge you a 1 hour shop rate??

Feb 10, 2010 | 2005 Jeep Grand Cherokee

1 Answer

How to make reset for service alert for my mercedes ml 320


To reset the service alert light, perform the following:

Within the first 4 seconds after moving the start switch to position 2, press the reset button for the trip counter twice within one second. The display for the service request is activated for about 10 seconds.

Within these 10 seconds, move the start switch into position "0". The service request continues to be displayed.

Press the reset button for trip counter and keep it pressed.

Move the start switch into position "2".

Continue to hold the reset button for the trip counter pressed until the signal sounds and the new start distance appears in the display (it takes about 10 seconds).

Nov 08, 2009 | 2006 Mercedes-Benz ML-Class

1 Answer

EVIC - PERFORM SERVICE MESSAGE


To reset the perform service message , is as follows , turn ignition switch to the ON position , depress and release MENU push button until SERVICE INTV . = is displayed , press and release STEP button to step through available options. the last selected distance option displayed becomes the service interval at which the PERFORM SERVICE message will be displayed . if a new distance interval is selected , RESET SERVICE DISTANCE ? with a yes or no option. when yes is selected the accumulated distance since the last previous PERFORM SERVICE message will be set to zero because the service interval has been changed . when NO is selected , the distance until the next PERFORM SERVICE message is reduced by the accumulated distance since the last previous message . EVIC exits programming mode and returns to its normal operation mode when the C/T button is depressed or when the end of the programmable feature menu list is reached , whichever comes first .

Thanks for asking .

Dec 30, 2008 | 2002 Jeep Grand Cherokee

1 Answer

Perform service light is constsntly on


i had same problem.u have to press step untill miles to service then press reset for 3 seconds . hope it helps

Dec 01, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...