Question about 2002 Chrysler PT Cruiser

2 Answers

Shut off on the interstate and wont crank up. we changed the cam sensor the crankshaft sensor and the battery. it turns over but wont crank.

Posted by on

  • Anonymous Mar 31, 2014

    Car turns over but won't start changed cam senser an crankshaft sender still won't start

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

Well, During this time when you replaced the cam sensor and stuff did you check to see if the timing belt was still intact? Do a compression check to see if you've lost compression on any cylinders. If the timing belt broke this will be the case. Chrysler typically has a plastic cover that goes over the cam pulley end of the timing belt that can be removed, it also has a check hole, to check the timing belt as well.

Posted on Jul 22, 2010

Testimonial: "i was worried about the timing belt. but we can see the valves moving"

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Had similar situation in the Badlands NP. Finally removed the gas cap. We had an air lock in the fuel system.

Posted on Aug 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 grand cherokee wont start changed crank ,cam, map,fuel filter/relay back by the tank,got 53psi on the fuelrail,new computer new relays


just a couple thoughts. Injector fuse and relay(does fuse and relay have power to and from them). My understanding is sometime Anti theft will shut down injection pulse so car can not be run. Maybe even timing chain broke. I assume there is no trouble code.

Aug 05, 2017 | Jeep Cars & Trucks

2 Answers

97 oldsmobile achieva wont fire changed coil pack spark plugs cam sensor still wont start


Make sure battery has a full charge and battery connections all good.
If it cranks good but won't start, have a helper crank it while you visually check for spark at the spark plugs. If spark everywhere, use a gage and check proper fuel pressure and fuel injector pulse.
If you having a problem with more than one system, I want to check for rpm signal, that usually comes from the crank sensor. Not sure why you replaced cam sensor? I always want to check sensor wiring circuits before replacing anything. Don't replace anything unless your testing points in that direction.

Nov 04, 2016 | Oldsmobile Cars & Trucks

1 Answer

Changed crankshaft sensor,car turned over while car started i pulled battery cable to see if needed a alternator, car ran for a minute then shut off, now car will turn over but wont start again,


pulling the battery wire is the worst thing you could do
st it energized the immobilizer
next it is a good way of blowing the alternator
to check if the alternator is working simply put a multimeter across the battery terminals

Oct 21, 2015 | Cars & Trucks

1 Answer

My car shut off while driving, computer codes are P0562, P0340, P0700, P0016 I need help


P0016 is for camshaft/crankshaft misalignment. You should check and verify that the timing chain is still intact and that the cam/crank timing is correct. If the engine is cranking really fast and does not sound like there is compression, it is probable that this chain/chains have jumped &/or broken.

Sep 14, 2012 | 2006 Dodge Stratus

1 Answer

2001 crankshaft sensor changed now car want start


If the store pulled the codes and it had a code for the crank sensor, the real problem could be a bad cam sensor or a problem with the crankshaft. The crank sensor "sees" a mark or magnet on the crank and sends a signal to the computer. The computer takes that signal and compares it to the cam sensor to start the engine then runs off of one or the other. It sounds like the computer is not seeing the two signals match up.

Jun 24, 2012 | 2001 Chevrolet Cavalier

1 Answer

1998 durango 5.2 wont turn over. changed computer,dist,crank and cam sensors,changed ignition module. no spark to coil...has ignition pulse... any ideas? thanks!


Crankshaft position sensor? Did you check for a trouble code??? I would have to say at this point there is a code stored in memory.

Nov 23, 2010 | 1998 Dodge Durango

2 Answers

2001 mazda mx5 miata won,t crank. replaced crank, cam, and knock sensors. flashing engine light and missing.


SOUND LIKE CRANKSHAFT SENSOR OFF.TOO MUCH GAP FROM CRANKSENSOR TO CRANKSHAFT PULLEY PULSE WHEEL.

Mar 08, 2010 | 2001 Mazda MX-5 Miata

1 Answer

It wont start. I was driving and it just shut off, didnt spudder out just shut off. it turns over like a normal start just doesnt crank. ive replaced the cam sensor behind the hormonic balancer. the fuel...


That's the crankshaft sensor by the harmonic balancer. Is it a V-10 or what engine? It could be the cam sensor which is located on the front of one of the heads I don't remember which one. Did the "Check Engine Light" come on? There should be code that will point you in the right direction. Also, check the fuses.

Dec 05, 2009 | 2005 Ford F 350 Super Duty

4 Answers

My chevy express van 1500 cranks but wont start


test and see if you have spark and fuel preasure, you may have bad feul pump, common problem is the fuel pump goes bad, but check before replacing.

Oct 01, 2009 | 2000 Chevrolet Express Cargo

1 Answer

Shuts off while running


change crank sensor and renew thermostat,once ok drain some water and add antifreeze

Oct 28, 2008 | 1996 Mitsubishi Eclipse

Not finding what you are looking for?
2002 Chrysler PT Cruiser Logo

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...