Check this procedure abut Alternator - Removal & Installation...
-
Before servicing the vehicle, refer to the Precautions Section.
-
Disconnect the negative battery cable.
-
Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
-
Remove the front air intake inlet pipe bolts, 1.8L engine only.
-
Remove the top hose from the air intake inlet pipe, 1.8L engine only.
-
Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
-
Remove the power steering pump, 2.0L engine only.
-
Remove the power steering pump bracket, 2.0L engine only.
-
Remove the alternator
B
terminal cover cap.
-
Disconnect the alternator electrical connections.
-
Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
-
Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
-
Remove the water pump pulley, 1.6L (VIN 3) engine only.
-
Remove the power steering pump, 1.6L (VIN 3) engine only.
-
Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
-
Remove the alternator tensioner mounting bolt and the belt tensioner.
-
Remove the alternator pivot bolt.
-
Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
-
Remove the alternator.
Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown
Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown
Fig. Alternator mounting-2.4L and 2.7L engine
To install:
-
Before servicing the vehicle, refer to the Precautions Section.
-
Install the alternator.
-
Install the alternator pivot bolt and hand-tighten at this time.
-
Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
-
Install the drive belt.
-
Adjust the belt tension by rotating the adjustment bolt.
-
The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
-
New belt: 0.22-0.28 in. (5.5-7mm).
-
Used belt: 0.24-0.28 in. (6-7mm).
-
The belt deflection for 1.6L (VIN 3) engine is as follows :
-
New belt: 0.13-0.15 in. (3.3-3.7mm).
-
Used belt: 0.17-0.19 in. (4.2-4.7mm).
-
The belt deflection for the 2.0L engine, is as follows:
-
New belt: 0.22-0.31 in. (5.5-8mm).
-
Used belt: 0.33-0.45 in. (8.5-11.5mm).
-
The belt deflection for the 1.8L engine, is as follows:
-
New belt: 0.23-0.31 in. (6-8mm).
-
Used belt: 0.28-0.35 in. (7-9mm).
-
Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
-
Connect the alternator electrical connections.
-
Install the alternator
B
terminal cover cap.
-
Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
-
Install the water pump pulley, 2006 1.6L engine only.
-
Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
-
Install the top hose to the air intake inlet pipe, 1.8L engine only.
-
Install the front air intake inlet pipe bolts, 1.8L engine only.
-
Connect the negative battery cable.
Hope help with this.
It was very helpful thank you
×