Question about 1993 Buick Century

Open Question

Need to replace a knock sensor for a 1993 buick century 3.3 6 cyl

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
jeffk14
  • 16 Answers

SOURCE: how to replace a coolant level sensor, 2000 buick century

TRY THIS. Good luck!

Posted on Nov 22, 2008

Ad
Papa Chan
  • 56 Answers

SOURCE: how to replace a coolant level sensor, 2000 buick century

The coolant level sensor is located on the radiator. If you are looking at the engine from the front of the car it will be on the left side. There will some kind of clip holding it in the radiator. Removed the clip and pull the sensor out. You will lose coolant so try to swap it out quick or drain some of the coolant out. Once new sensor is installed, install clip to keep the sensor in place and reconnect the wires to the sensor. Crank the engine and make sure the coolant level is full. This should correct your problem.

Posted on Jan 04, 2009

emissionwiz
  • 83054 Answers

SOURCE: Need to replace tail light bulb on 1996 Buick Century

Inside the trunk, under the carpet behind the tail lights will be a whole bunch of small plastic nuts, running from one side of the car to the other. Take all of these plastic nuts off, and the whole tail light assembly will come off in one large piece. Find the bulb you need to replace, and reassemble

Posted on Apr 06, 2009

66 chrgr
  • 1011 Answers

SOURCE: coolant temp sensor

BELOW THE THERMOSTAT HOUSING ON DRIVERS SIDE OF ENGINE

Posted on Apr 16, 2009

mechanicm639
  • 253 Answers

SOURCE: bad knock sensor on 1998 chevy malibu 2.4L

The knock sensor is on the back side of the engine near the trans. It is round, with a 1 wire connector. You will have to get it from underneath. Good Luck.

Posted on May 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Computer reset on 2000 buick


Test the coil pack for cyl #3 first. A bad coil will cause the computer to give that code. To reset the computer remove both battery cables and touch them together for a minute or two, then reinstall them and then go drive the car for more than 20 minutes in traffic, stop and go so the computer will relearn inputs from all the engine sensors.

Jan 12, 2018 | 2000 Buick Century

1 Answer

93 buick no start 3.3 no check engine light. code43 knock sensor. checked for power at knock sensor none. replaced ecu. checked all fuses all good has spark. will fire if spray in throttle body .


Sounds more like you have a bad fuel pump.If you have a pressure tester then check the fuel pressure.You need top have between 41-47 psi fuel pressure.

Nov 22, 2009 | 1993 Buick Century

1 Answer

Engine hi engine diagnose lite on scantool


ay chek all the ground wires that go to the ecm
chek alterneter and battery
chek ignation module and the knock sensor
every won was good
than ay change the ecm and the problem is over

Jun 20, 2009 | 1993 Buick Century

1 Answer

Buick century 1993 stalls while driving After driving for a while the car stalls out. It's dangerous because sometimes I'm on a highway. It starts immediately after that and goes a bit then stalls again....


i had the same problem with my 92 exept after mine stalled it wouldnt start for 20 - 30 mins... mine ended up needing a transmission flush for the stalling problem and i tried to drive everyday that helped
hope this helps in some way

Jun 13, 2009 | 1993 Buick Century

1 Answer

Car wont start 93 buick century


to find the crank sensor you have to remove the bell housing and then the plastic guard behind the bell housing....fusible links sorry I do not know

Jan 12, 2009 | 1993 Buick Century

Not finding what you are looking for?
1993 Buick Century Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

Marvin
Marvin

Level 3 Expert

83054 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...