Question about 1998 Ford Expedition

1 Answer

How should the display gauge look when car is off...i had to remove needles to replace face

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

All should be at zero mph and rpm, and temp, alternator, and oil at lowest point.

Posted on Jul 21, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 154 Answers

SOURCE: Replacing the gauge face

they just pull out

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

'04 Chevy Avalanche fuel gauge and shifter gauge PRND321 not working and temp gauge needle facing down ???


Early and mid 2000 GM Trucks have a instrument cluster issue, think the cluster is your problem and the unit will have to be repaired or replaced.

Jun 12, 2018 | 2004 Chevrolet Avalanche

Tip

How to Replace the planetary gear in an Odometer of car?


The procedure is follows:--
1) First of all disconnect the negative cable from the battery of car.
2) With flat head screwdriver, pry the gasket around the edge of the face of speedometer gauge away from the dash and remove the gasket.
3) You will have to pull the entire speedometer gauge out of the dash;
NOTE:-- do not to disconnect the connecting electrical wires when you pull speedometer.
4) Then remove the speedometer needle by turning the needle clockwise.
5) Then remove the two screws in the face of the gauge with screwdrivers.
6) Remove the motor casing for the odometer out from the dial after the screws are removed.you will need to pull the motor casing a bit to remove it out.
7) In the motor casing you will see the gear pod at the top of the motor casing. Slightly with bit force remove the gear pod. The gear pod is attached to the "lid" of the casing .
8) You will see the odometer planetary gear in the gear pod which you removed.Remove the planetary gear from the gear pod with the help of mini flat head screwdriver.
9) Insert new gear into position and reassemble the gauge by reversing the procedure.
this will help.Thanks.

on Mar 15, 2010 | Audi A4 Cars & Trucks

Tip

How to Repair an Odometer in car?


The procedure is follows:--
1) First of all disconnect the negative cable from the battery of car.
2) With flat head screwdriver, pry the gasket around the edge of the face of speedometer gauge away from the dash and remove the gasket.
3) You will have to pull the entire speedometer gauge out of the dash;
NOTE:-- do not to disconnect the connecting electrical wires when you pull speedometer.With the gauge face down remove the screws from the back of the case with a screwdriver. After removing the screws , lift the gauge out of its casing and see its back.
4) Then grasp the post to reset the trip odometer. Do it very carefully;
5) Then remove the speedometer needle by turning the needle clockwise.
6) Then remove the two screws in the face of the gauge with screwdrivers.
7) Remove the motor casing for the odometer out from the dial after the screws are removed.you will need to pull the motor casing a bit to remove it out.
8) In the motor casing you will see the gear pod at the top of the motor casing. Slightly with bit force remove the gear pod. The gear pod is attached to the "lid" of the casing .
9) You will see the odometer planetary gear in the gear pod which you removed.Remove the planetary gear from the gear pod with the help of mini flat head screwdriver.
10) Insert new gear into position and reassemble the gauge by reversing the procedure.

This will help.thanks.

on Mar 15, 2010 | Buick Century Cars & Trucks

1 Answer

2008 jaguar s series gas gage quit working


probably not all that difficult to fix it you have patience. The needle going way past full is an indication of a short before the sender unit or in the sender unit. Pull the power wire from the sender unit and see what the gauge does. IT should stay on the empty mark. IT may be just a fuel sender unit .

Dec 23, 2013 | 2008 Jaguar S Type

1 Answer

2001 honda accord speedometer needle stuck below pin


You need to get that needle over the pin. Remove the cluster face and manually do that.

Dec 20, 2013 | Honda Cars & Trucks

2 Answers

Fuel Gauge spun around in opposite direction. The electronic display still shows the mileage remaining. What could the problem be???


It will take about 30 min to fix. Well that's how long it took me to reapair my 2006 SL. First remove the 3 screws from the shroud around your column they are under your column. Make sure your column is extended and in its lowest position. Second remove the 3 trim pieces on top of the cluster by using a flat blade screwdriver be careful not to damage your dash. Third remove the single screw on top of the cluster and the two that are underneath. Fourth release the tabs that hold the bezel around your cluster. Fifth each lens can then be removed exposing the gauge face and needles. Sixth gently move the needle counter clockwise until it rest on top of the needle stop. Seventh try to remember how it all goes back together haha. No really it is a piece of cake 30 to 40 min versus the 2 hour quote from my local Nissan dealer.

May 19, 2009 | 2006 Nissan Maxima

1 Answer

Problem with temp, battery and oil gauges, speedometer erratic.


get the original company service and repair manual from the given link it will help you to fix all the facing problem along with diagram

Oct 09, 2017 | 2005 Ford Mustang

1 Answer

96 Maxima gauge needles


Here I hope this works for you step by step for removing needle from gauage. Click the word needle. This will take you to a step by step guide. All needles are the same to remove no matter the make of the car

Feb 09, 2009 | 1996 Nissan Maxima

1 Answer

Ford focus mk1 speedo not working after install. of glow gauges


PUT THE NEEDLE BACK ON WITH THE KEY OFF AT OOOOOO

Jan 17, 2009 | 2003 Ford Focus

Not finding what you are looking for?
1998 Ford Expedition Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...