Question about 2000 Lincoln Navigator

2 Answers

Changed the battery two weeks ago. Running great. New pads and rotors changed on Monday...Wed it is deader then a door nail. Had to use key to unlock the door (usually can use the key pad) Any suggestions?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 5,653 Answers

You can get a defective Battery. Go to Autozone or Oreillys and get the Battery tested and then bring the Lincoln in for an Alternator scan. When you pull the Battery out of its mount, look for FUSIBLE link wires in that area which could have been pinched when the Battery was changed. With Luck you're fixed.

Now the bad news. If the Air ride was not turned off when the Rotors and Brakes were done, the books say it can harm the Suspension. Since the Airride is Automatic, it can drain the Battery if it runs when it should not. There is a Diagnostic plug for the Airride, but you would have to call to see if they have the extra scanner for this special plug.

While you would want the Brake place to be Responsible for the damage, it may be better to have a 3rd party test your Airride.

Posted on Jul 22, 2010

Testimonial: "Thank you so much for your help :) I think you are correct about the Air ride suspension :( That went two days later."

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Is your door adjar light on ??? these are notorious for rear wiper motor transmission between the glass going bad and cause a draw ;)

Posted on Aug 18, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remote key


Yes - Sometimes when the battery is replaced the key program can be corrupted. It would be a starting point to have the key reprogrammed just to eliminate it as a source of trouble.

Jan 10, 2014 | 2009 Chevrolet Malibu

1 Answer

I'm driving a 2000 Chrysler 300M. Had front brake pads & rotors changed 2 weeks ago. Front end has been noisy since & I suspect sticking calipers , as i was informed they did not get clean


The front calipers are not the problem...did a shop replace the pads and rotors? Or did a friend replace these parts. The Chrysler front pads and rotors are an excellent design...easy to service and replace parts...only 2 bolts hold on each caliper, and the rotor is held in place with the caliper, and wheel. My first thought was a front wheel bearing is grinding, but you should have noticed this before the brake parts change. The pads could be installed backwards also...my second thought was you may have a loose wheel or two...retighten all 5 lug nuts by using the "star" tightening method, you may be surprised that the loose lug nuts are the only problem. Hope this helps.

Jul 12, 2012 | 2000 Chrysler 300M

1 Answer

I changed the rear rotors and pads on my 2005 Grand Prix GT a few months ago and now the left rear is not releasing properly after applying the brakes. How do I fix this?


Hello, my name is brad and im here to help.when you install your new rotors and pads,you had push in the calipers,did they push hard or fast,if hard you have stickey caliper,if not a colapst brake hose.hope this helps,have a great day and thank you.

Sep 17, 2011 | 2005 Pontiac Grand Prix

1 Answer

I have a problem with my 2005 Crossfire not starting after sitting for a couple of days. I don't drive it every day and it may sit for any where from 7-12 days at a time. But when I go to start it, it's...


new cars have a lot of things running in the back ground, you can hook and AMP meter on the battery and see how much it pulls just sitting there, then one by one unplug fuses and see if maybe a relay has welded its self closed and drawing more current then it should in the off postion. if possible hook a battery tender to your car and plug it in, it will keep a small amount of current going to the battery and should keep the battery charged.

Apr 04, 2017 | 2005 Chrysler Crossfire

1 Answer

Vibrating, Squeak, Grinding After Changing Pads and Rotors


mcdevito75 here, You most likely have the cause, on of the caliper bolts got loose, Check both sides, make sure the pads are seated correct and that all bolts on both fron wheels are tight.

Jun 16, 2010 | 2003 Chrysler Town & Country

2 Answers

2001 GMC Sonoma won't start


The battery may have went completely dead, even though it was just changed.

Feb 24, 2010 | 2001 GMC Sonoma Extended Cab

1 Answer

Front brakes make noise when applied after installing new pads.


it could be because they are dirty. also the noise could be the back brakes. if its a squeaking noise it could be that they are dirty or that they are cheep brake pads and for the first couple of weeks they squeak. also when you got your breaks changed did the break shop cut the rotors because that cleans them up and makes the rotors like new.

Apr 28, 2009 | 2003 Suzuki Grand Vitara

1 Answer

Aurora 2001. Car can't sit for 2 days untill the car is deader than a door nail. Have tried turning everything off except security light. They tell me everything checks out ok. Battery is new


It may take a while to do this - take out one fuse at a time and let it set for the same time period that now kills it. You will eventually find one that being out does not kill the battery. Then you know exactly where to look.

Mar 25, 2009 | 1997 Oldsmobile Aurora

1 Answer

I just changed my front disc and pads 6mths ago .


did you have the rotor machined so that the rotor is smooth and flat this could very well be the problem

Mar 17, 2009 | 2000 Dodge Caravan

1 Answer

1992 cavalier brakes hard when not running soft when started changed the booster (used) pads are good shape,rotors ok, changed master(used) Bleeded them still the same. maybe new rotors and pads? vacume...


Bad vacum or a bad master.... rotor and pad would have no affect on petal feel. never use used parts in a brake system, new or remanufactured only!!

Jan 06, 2009 | 1992 Chevrolet Cavalier

Not finding what you are looking for?
2000 Lincoln Navigator Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

fordexpert

Level 3 Expert

5653 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...