Question about 1995 Honda Accord

1 Answer

I want to know what the engine look likes with the radiaters and fans in it

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 6,826 Answers

I know that this may not be what you want, but it does cover how to remove the Engine Fans REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable.
  2. On some models, it may be necessary to disconnect the coolant hoses from the radiator to allow clearance for removing the fans. If so, drain the cooling system, then disconnect the hoses.
  3. Unplug the fan electrical connections.
  4. Remove the mounting bolts holding the fan shroud and remove the shroud with the fan. Once removed, the fan blade may be unbolted from the shaft and the fan motor removed from the shroud. Fig. 1: The fan shrouds are secured to the radiator with a series of small bolts i want to know what the engine look likes with the - 86803064.jpg
    Fig. 2: When removing the fan shroud, be careful not to damage the radiator cooling fins 86803065.jpg
    To install:
  5. Position the fan on the radiator and install the mounting bolts. Tighten them to 5 ft. lbs. (7 Nm).
  6. Engage the electrical connections.
  7. If applicable, refill the cooling system.
  8. Start the engine and allow it run until it reaches normal operating temperature. Check that the fan(s) turn on. Check for leaks.
next.gif

Posted on Jul 21, 2010

  • Duane Wong
    Duane Wong Jul 21, 2010

    There are generally two fans one on each side with shrouds around them. They are removed to get at the radiator when it needs service, and are held on with bolts that are torqued to only 5 ft. lbs.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fan located in a 97 Mercury Tracer?


You're looking for something like this:

Allstar Performance 6 Blade Fans ALL30102

It's usually located at the very front of the engine in front of the radiator. It is located inside a fan shroud.
Allstar Performance Fan Shrouds ALL30114

The fan circulates fresh air into the radiator and engine to help keep it cool.

WARNING: when the engine is running, the fan is rotating (very quickly!), so you most likely will not be able to see it. It is dangerous, so do not stick your hand or anything else into the area when the engine is running.

... How Does Radiator Fan Work DoItYourself com

..

May 12, 2016 | Mercury Cars & Trucks

4 Answers

Why want radiator coolant fans works for a 99


There is a fuse box on top of the battery. Check there for melted or corroded fuses. Those like to get all deformed and fans don't work.

Sep 22, 2014 | 1999 Volkswagen Beetle

1 Answer

Mercedes fan


If it gets hot at a seady 55-60 mph.It's not a fan problem.They are only for low speed.If it gets hot running down the road ,more likely a head gasket.One is the engine fan ,the other for the A.C. Don't know where the relay is for the engine fan,anybody else?

Feb 03, 2014 | Cars & Trucks

1 Answer

Fan comes on when switch ignition on instead of when hot Tazz


If the fan not turning on when car engine getting hot,then car will notice overheating.Click this link below for troubleshooting:---http://technoanswers.blogspot.in/2012/02/car-running-hot.html--------To know how engine cooling system works ,click the link below :----Engine cooling components working?

http://repairhelpcenter.blogspot.com/2011/11/engine-cooling-components-working.html

------------------
How does Vehicles Engine cooling system works? http://repairhelpcenter.blogspot.com/2011/11/how-does-vehicles-engine-cooling-system.html
------------How to Replace Engine cooling Fan:-- http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-engine-cooling-fan-on.html
-----------Replace Fan Relay but still Radiator cooling fans not working? http://schematicsdiagram.blogspot.com/2011/12/replace-fan-relay-but-still-radiator.html
----------DIC says "COOLING FAN FAULT"? http://schematicsdiagram.blogspot.com/2011/12/dic-says-cooling-fan-fault.html
---------Where Is Radiator Fan relay and Fuse Located?

http://schematicsdiagram.blogspot.com/2011/12/where-is-radiator-fan-relay-and-fuse.html

--------

This will help.

Thanks.

Feb 09, 2012 | Cars & Trucks

2 Answers

My 99 alero v6 is over heating not leaking ight mite be hoses or thermostat . or head gasket but when it overb heats the smoke comes from the top of the engine


REPLACE THERMOSTAT AND RADIATOR PRESSURE CAP.IF CAR OVER HEATING WHILE IN MOTION.MORE LIKELY ITS THE THERMOSTAT,LOW COOLANT IN RADIATOR OR COOLANT SYSTEM,BAD WATER PUMP,WATER PUMP WEEP HOLE IS LEAKING, WATER PUMP NEEDS REPLACING.CHECK ENGINE OIL,IF OIL LOOKS LIKE MILK SHAKE YOU HAVE LEAKING HEAD GASKET.IF CAR IN PARK AND OVER HEATS WHILE IN A LONG TRAFFIC LINE OR.BANK DRIVE THROUGH COOLANT FAN NOT TURNING ON, BECAUSE THE ENGINE COOLANT TEMPERATURE SENSOR FAULTY.CODE SCAN CAR FOR FAULTY COOLANT FAN RELAY OR FAULTY PCM. CHECK COOLANT FAN FUSE, AND HOT WIRE THE COOLANT FAN TO MAKE SURE ITS WORKING.IF COOLANT FAN DONT WORK WHEN HOT WIRED. COOLANT FAN NEEDS REPLACING. REPLACE BOTH RADIATOR HOSES, REPLACE THERMOSTAT AND RADIATOR PRESSURE CAP.BUY NEW COOLANT ADD 50/50 WATER AND COOLANT.IF ENGINE OIL HAS ANTIFREEZE IN IT.REPLACE ENGINE OIL AND OIL FILTER TO KEEP FROM LOCKING UP THE ENGINE.GET CAR FIX.DONT KEEP DRIVING IF IT KEEP OVER HEATING,ENGINE DAMAGE WILL OCCUR.I HOPE INFORMATION I GAVE YOU WILL FIX PROBLEM.PROBLEM COULD BE LEAKING RADIATOR HOSES BUT CHANGE THERMOSTAT THATS FIRST THING I WOULD CHANGE BECAUSE IF IT CLOSED, ENGINE WILL OVER HEAT AND CRACK CYLINDER HEAD OR CRACK PISTON, COOLANT NEED TO CIRCULATE THROUGH THE ENGINE TO TAKE AWAY THE HEAT FROM ENGINE.

Apr 19, 2011 | 1999 Oldsmobile Alero

2 Answers

Overheating car


This is a fairly common problem. The engine is overheating because the secondary fan is most likely not coming on. Here is a good way to check. With the car in park and the engine idling turn on the air. When the air is on the secondary fan should start. If the fan doesn't start then you have found the problem. The fan relay is usually the problem. You can locate this relay by looking in your owners manual. also check the fuse and the plug at the fan for a loose connection. hope this helps. Good luck.

May 11, 2009 | 1996 Oldsmobile Aurora

1 Answer

1989 Dodge Shadow radiator fan won't come on. If I supply direct battery to the fan it comes on so I know the fan motor is good. What should I check? Thanks.


Sounds like the relay switch. Look in owners manual to see where it is located. I know some are under the dash and some in the engine compartment.

Apr 28, 2009 | 1989 Dodge Shadow

1 Answer

I need 2 know how to remove the radiator


THIS IS a 1995 LINCOLN CONTINENTAL W/4.6L ENGINE
iIBELIEVE TOWN CAR IS DIFFERENT LET ME KNOW IF SO AND PLEASE DONT FORGET TO RATE ME


REMOVAL
  1. Disconnect battery ground cable (14301).
  2. Drain engine coolant.
  3. Remove engine air cleaner (ACL) (9600).
  4. Remove upper radiator hose (8260) from water bypass tube.
  5. Remove radiator overflow hose (8075) from radiator (8005) and fan shroud (8146). NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
  6. Remove transmission oil cooler line from oil cooler inlet fitting.
  7. Remove nuts retaining A/C condenser core to the radiator.
  8. Disconnect engine control sensor wiring (12A581) from the auxiliary electric cooling fan motors and the CCRM.
  9. Raise vehicle on hoist.
  10. Remove splash shield from lower radiator support (16138) and front sub-frame (5C 145).
  11. Remove lower radiator hose (8286) from radiator. NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
  12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
  13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
  14. Support fan shroud, radiator and A/C condenser core (19712) with a suitable jackstand. Remove lower radiator support. Position jackstand aside and carefully remove radiator and fan shroud.
  1. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
  2. Remove upper radiator hose from radiator.
INSTALLATION
  1. Follow removal procedure in reverse order.
  2. Tighten fan shroud bolts and A/C condenser core nuts to radiator to 3-5 Nm (27-44 inch lbs.) .
  3. Tighten lower radiator support bolts to 8-11 Nm (71-97 inch lbs.) .
  4. Tighten transmission oil cooler lines to fittings to 25-28 Nm (18-21 inch lbs.) .
  5. Tighten power steering/transaxle oil cooler and splash shield retaining screws securely.
  6. Refill engine coolant.

Feb 11, 2009 | 1995 Lincoln Continental

Not finding what you are looking for?
1995 Honda Accord Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...