Question about Cars & Trucks

1 Answer

Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 6,826 Answers

To Install:
NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
Hiwich timing mark I used to time the balancer - honda-03-23-3425.gif

  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

  3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

  12. Turn crankshaft pulley unHiwich timing mark I used to time the balancer - honda-03-23-3426.gif honda-03-23-3426.gif

  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Hiwich timing mark I used to time the balancer - honda-03-23-3556.gifd tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maiHiwich timing mark I used to time the balancer - honda-03-23-3557.gifle in balancer shaft.
  21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

  22. Align groove on balancer shaft with pointeHiwich timing mark I used to time the balancer - honda-03-23-3556.gifg.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjustinHiwich timing mark I used to time the balancer - honda-03-23-3537.gif> Crankshaft pulley, bolt and washer must be cleaned prior to installation.
  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

    CAUTION
    Do not use impact wrench to perform following step.
  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
  35. Install dipstick/tube assembly.
  36. InstalHiwich timing mark I used to time the balancer - honda-03-23-3420.gifen bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.
prev.gif next.gif

Posted on Jul 21, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 honda accord vtech timing belt marks


The Honda F23 series engine is a 2.3 liter, all aluminum block, 16 valve, Single Overhead Camshaft (SOHC) motor used in the Honda Accord (1994 - 2002) and Acura Cl (2.3). Timing belt failure may result in either the intake or exhaust valves bending after contacting the pistons. If the belt has broken, a Compression Leakage test is advised to determine if the valves require replacement. Compression leakage from any of the cylinders (indicating bent valves) will require the removal of the cylinder head. An inspection and rebuild of the head by a reputable automotive machine shop is recommended in lieu of doing it yourself. This DIY article only covers belt replacement. The belt replacement interval is either 90,000 or 105,000 miles based on the specific model year. Check the owner's manual for the specific service interval. If the mileage is below the threshold but the vehicle is over 7 years old, consider performing a replacement as preventative maintenance (PM). Timing belts cannot be visually inspected for wear. Moreover, a visual inspection would require the removal of the timing belt cover which in itself is time consuming and better spent working on replacement. A typical timing belt component kit consists of: 1. Timing Belt 2. Balance Shaft Belt. 3. Timing Belt Tensioner Pulley. 4. Balance Shaft Tensioner Pulley

Sep 28, 2016 | 1999 Honda Accord

1 Answer

Do the 2 balance shafts in the oil pump have to be timed together


92 accord 2.2 rear balance shaft - YouTube

? 2:17
https://www.youtube.com/watch?v=RcrvchGkJdA
Mar 31, 2012 - Uploaded by Shasta Sweetbottom
I believe this is the correct way to set the rear balance shaft on a 92 2.2 accord. ... 1 time, it has gear inside ...

VW and Audi TDI oil pump failure and balance shaft FAQ ...

? 6:54
https://www.youtube.com/watch?v=xHa5TPFNc2M
Oct 5, 2014 - Uploaded by myturbodieseldotcom
http://www.myturbodiesel.com/wiki/oil-pump-failure-or-balance-shaft-module- ... Does the 2013 Volkswagen ...

2.4L balance shaft on oil pump sprocket - Kia Forum




Nov 24, 2015 | Cars & Trucks

1 Answer

Are there markings for tdc on both balancer shaft for a 1993 honda accord and how do you set them to tdc?


There's one balancer shaft the other is idler/tensioner pully
the balancer shaft carry a groove on it should be facing up

Jul 05, 2015 | Honda Cars & Trucks

1 Answer

I just bought my first car 1998 honda accord did a complete tune up but it vibrates when idle but run smooth.


some hondas have a counter balance shaft on lower part of the engine (marks should be lined up when replacing timing belt ) someone may have replaced timing belt and missed aligned them

Feb 28, 2015 | 1998 Honda Accord

1 Answer

Balance shaft alinement marks on honda 2.3 litre engine


set it to top dead center. there's an access hole to put a 4" or 100mm pin to keep the balance shaft from moving when replacing a timing belt. The other marks are at the cam and crankshaft pulleys.

Or remove #1 cylinder spark plug, put a wooden rod against the piston, when it is at the top of it's travel and goes neither up or down, it is at top dead center. The balance shaft locking pin can then be inserted.

Jul 12, 2010 | 1998 Honda Accord

1 Answer

How to line crank and cam for timing belt on 1988 no crank marks


Hard to explain here... but I believe that car also has the balance shaft which needs to be timed as well. The camshaft has 2 lines which line up to the top of the head, and a "up" or "top" mark at the top.
Crank is set to 0 degrees.

May 02, 2010 | 1988 Honda Accord 4 Door

1 Answer

I am trying to set the timing mark on a 1996 honda accord with a 2.2L 16 valve. The cam and crank mark are okay. The only one I am concerned with is for the oil pump and the balancer. I heard that to set...


get a book i dont thing you have a clue whats going on here . you set the crank shaft and the came shaft marks on a 2.2 thats it . if you go to mitchell repair manuals you can buy a manual for $9.99 . may save you a big head ach

Oct 28, 2009 | 1996 Honda Accord

2 Answers

I removed my timing belt from my 1992 honda accord


The balance shafts have marks on their sprockets that line up with indents on the block. For the one with the pin, just use a drill bit shaft that seems to fit the best and look for the marks. You only have two choices as you turn the balance shaft and expose the alignment hole. One of those spots will have fairly obvious marks that line up at the sprocket. The other one has a mark toward the front of the block. I'll see if I can dig up a photo and post it. The other tricky part is tensioning the belts, it's done in two steps while half the tensioner is clamped in place by a spare timing cover bolt. If you need help with this, let me know.
Please, please don't forget to remove the alignment pin or the bolt you used to clamp the tensioner!

Apr 01, 2009 | 1992 Honda Accord

1 Answer

Timing belt replacement 94 Accord


HI train fixer
You would find the following utube site helpful----- dave's farm I think he has a clip on this.

Feb 19, 2009 | 1994 Honda Accord

2 Answers

Timming belt


hi the balance shaft has to set by removing the bolt in the engine block that is in line with the front of the balance shaft the get a 6mm bolt that is 100mm long slide it into the hole where you revoved the bolt turn the balance shaft keeping a slight pressure on the bolt until it locates the hole in the shaft and locks it up then if you look at the oil pump there is a mark on the top of the housing and the oil pumps shaft just line them up stick your belt on tension and remove the locking bolt yates210456

Oct 10, 2008 | 1997 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15148 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...