Question about 2002 Ford Escort

Open Question

Need a picture of timing marks for 2002 ford escort 2.0 single over head cam

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: changing timing belt

LINE THE POINT ON THE CAMSHAFT SPROCKET WITH THE DIMPLE IN THE HEAD, THEN THERE WILL BE A NOTCH IN THE CRANKSHAFT SPROCKET THAT LINES UP WITH THE NOTCH RIGHT ABOVE IT, YOU SHOULD BE ABLE TO FIND IT! MAKE SURE IT IS THE SPROCKET AND NOT THE PULLEY CAUSE IF I REMEMBER RIGHT THEY AREN'T THE SAME.

Posted on Nov 17, 2008

Testimonial: "thank you"

Ad
mabpest
  • 1152 Answers

SOURCE: where should timing mark on camshaft be on 1999

Support the engine with the floor jack and remove the right hand side motor mount and bracket. Raise the engine slightly and remove the timing belt cover and the crankshaft pulley bolt and the pulley. Turn the engine clockwise until the crankshaft timing marks are lined up. There is a triangular mark on the crankshaft and a plate with a mark at 12 o'clock on the block. The camshaft has a triangular mark on the sprocket and a dot on the block at 12 o'clock that must line up.

Posted on Jan 29, 2011

  • 316 Answers

SOURCE: I need the timing marks for a 2000 escort with

The timing marks are a arrow on your cam gear, and a dot on your cylinder head; align them.

Your crank gear has a tab, and the engine has a groove; align them.

After aligning the marks and putting your timing belt on, turn the engine 2 complete turns to insure the marks are still aligned; As long as the marks still align, you're done.

I hope this helps you, and if you need further assistance let me know.

Posted on May 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a ford focus timing marks single overhead cam diagram


depending on trans and engine mount type the mark my be on flywheel but generally most cars it is located on the belt pulley attached to crank rod, center bottom one on engine block. the timeing mark should be visable from top looking down. if you use a big ratchet to turn over the engine by hand and go slowly, you should see thhe marks pass as you do so.

Aug 14, 2014 | 2002 Ford SVT Focus

1 Answer

Need timing marks on 1997 escort


timeing mark for the top is located on the upper cam in the center of the wheel is a lil spike that lines up with a dot on the head behind the timeing cover lower timeing mark is located on lower crank u will see a notch in the crank while looking from the top of the motor line those 2 up they both should be pointing up

Oct 21, 2011 | 1997 Ford Escort

1 Answer

Need a DIAGRAM FOR A FORD ESCORT 1999 TIMING MARKS


2.0 single over head cam ?

airjer995.gif

2.0 DOHC you'll need the tools to lock the cams and crankshaft in place before you install the timing belt.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Jan 23, 2011 | 1999 Ford Escort

1 Answer

I need to know the timing marks on a 1995 escort 1.9l


The timing marks are on the timing cover for the crank pulley, and on the cyl head for the cam

Dec 05, 2010 | 1995 Ford Escort

1 Answer

Set timing marks for escort zetec 16 v


valve timing marks on back of cams ,a slot on back of cam has to level with the head ,crank timing on the flywheel ,hole in bellhousing

Jun 10, 2010 | 1996 Ford Escort 4 Door

1 Answer

Where can i find the timing marks on 1998 ford escort zx2 ?


Hello pamgolmon: My name is Roger and i will answer your question. The 2-0 dual cam engine is a interference engine. This means if the engine jumps time at the timing belt. It will bend the valves. As for the timing marks on the camshafts. Their are no marks to be located. To set the timing marks on this engine requires special tools. This makes it expensive for not only the do it yourself mechanic but also the repair shops also. If the valves were bent you must pull the head for the repairs also.
I know this is not the answer you were hoping for but it is the only answer to give. Please rate the quality of the answer as this way we know your answer was correct. Please just ask if you need further help. Thank You for using Fix Ya. Roger

Sep 09, 2009 | 1998 Ford Escort

1 Answer

I need the timing marks for a 2000 escort with sigle over head cam.


The timing marks are a arrow on your cam gear, and a dot on your cylinder head; align them.

Your crank gear has a tab, and the engine has a groove; align them.

After aligning the marks and putting your timing belt on, turn the engine 2 complete turns to insure the marks are still aligned; As long as the marks still align, you're done.

I hope this helps you, and if you need further assistance let me know.

Apr 28, 2009 | 2000 Ford Escort

1 Answer

Need to know where the marks need to be for timeing belt on a 1998 ford escort wagon with a 4 cylinder. Thank You,


You didn't say which 4 cylinder engine you have, whether it is a single or dual cam engine? I am assuming since it is a station wagon it is the single cam engine.
On camshaft gear you should see a little arrow or pointer in one of the windows of the gear,it should be at the top and should line up with a dot on the head. The crankshaft pulley groove should be at the top and it should line up with a dot on the block or TDC/ 0 on the guage.

Feb 02, 2009 | 1998 Ford Escort

1 Answer

Changing timing belt


LINE THE POINT ON THE CAMSHAFT SPROCKET WITH THE DIMPLE IN THE HEAD, THEN THERE WILL BE A NOTCH IN THE CRANKSHAFT SPROCKET THAT LINES UP WITH THE NOTCH RIGHT ABOVE IT, YOU SHOULD BE ABLE TO FIND IT! MAKE SURE IT IS THE SPROCKET AND NOT THE PULLEY CAUSE IF I REMEMBER RIGHT THEY AREN'T THE SAME.

Jun 06, 2008 | 1990 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

585 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...