Question about 1999 GMC Yukon Denali

1 Answer

I have a 1999 Yukon Denali it was getting stuck in park. Took it to a garage they told me it was the brake switch. They replaced it and by the time I got my truck home, it got stuck in park again. What could be the problem and will this be an exspensive problem?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 66 Answers

Hi,I would check the wires at the plug on the brake switch.thay are very fine wires and tend to break at or near the switch connector.You can turn your ignition on but do not start the engine,push on your brake pedel wiggle the wires and listen for a click.It will click when the wires make contact.You will have to have the wire or connector repaired.Let me know what you find and if I can help any more just let me know.Thank You for using fixya.....iluv2fish........Ray.....

Posted on Jul 21, 2010

  • skj647 Aug 10, 2010

    Hello Ray,
    Just wanted to get back to you about the problem I was having with my truck. It turns out the garage put in a used brake switch!! I had it fixed for FREE and made sure they installed a new one from a GMC dealership.

  • Raymond A. Yoder Sr. Aug 10, 2010

    Hi,I'm glad everything turned out good for you and thank you for the feedback....iluv2fish...........Ray........

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Yukon Denali stop shifting out of park.


Check the brake lights when this happens, if they are not on then you have found the problem it is the brake light circuit. Go under the dash if the brick lights don't work and check the brake light switch above the brake pedal, it should have 12 volts in and out with the brake pedal pushed down. See typical brake light switch location below. #4 in diagram is brk lite switch.
10_12_2012_2_06_31_am.gif

Oct 11, 2012 | 1999 GMC Yukon Denali

1 Answer

Stuck in park


The most common problem for this is a bad brake switch. Get under the dash and follow your brake pedal up untill you see a switch that is operated when you press and depress your brake pedal. Replace this switch and you should be good to go.

Aug 15, 2012 | 1999 GMC Yukon Denali

1 Answer

My 1999 gmc yukon denali won't shift out of park


Check the brake switch. The brake switch releases the locking pin for the shifter when you apply the brake. Common problem with GM. Turn the key on, apply the brake on and off and listen to see if you hear a click in the steering collumn. Do this a few times to make sure you can hear it. If you can't then the switch is bad.

Jul 13, 2011 | GMC Yukon Denali Cars & Trucks

1 Answer

2001 Yukon Denali: The security light came on my 1999 Yukon Denali ye...


The security system (Passlock) is having problems, it's typical on those trucks. You can find a great write-up here: http://newrockies.ca , it was the only thing that saved my Park Avenue.

May 16, 2010 | 2001 GMC Yukon Denali

1 Answer

Can't get rear parking brake off 04 Yukon Denali XL


You are going to have to pry it over the axle on one side of the park brake shoe assembly with either a pry bar or screwdriver. then just pop the new one back over the axle in the same way. Hope this helps

Aug 05, 2009 | 2006 GMC Yukon Denali

1 Answer

How do i remove the brake light switch from a 1999 yukon denali, i can see like clips but not sure.


There may be two screws, open tailgate look to the inside by the seal around back. take the screws out, remove lens

Jul 31, 2009 | 1999 GMC Yukon Denali

1 Answer

03 Yukon denali park brake warning wont turn off


hi for info the brakes warning light on dash is also an indication that brake fluid level is low? or there may be a leak resulting in fluid level drop ? also considering age of car you may need to inspect brake pads wear ? if your car has low brake pads wear indicators attached to pads ? or the hand brake switch req's checking to ensure it is being pushed to off position when h/brak is down ? so fluid level low is the obviouse 1st check as fluid will displace from reservoir as pads wear low hence the level indicator on fill cap trips on may i suggest if it is low level b4 you top up? check your b/pads if you have not done so recently? or replaced since new ? hope this helps you locate problem best wishes from the uk

Jan 02, 2009 | 2003 GMC Yukon Denali

1 Answer

Fuse panel


PARK LP Fuse #12
30A
Park Lamp Relay, Headlamp and Panel Dimmer Switch-Park Lamps
Have you towed a trailer? if so maybe the trailer wiring is shorted.

Oct 02, 2008 | 2002 GMC Yukon Denali

Not finding what you are looking for?
Cars & Trucks Logo

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...