Question about 1994 GMC Suburban

1 Answer

Is there a clip on the retaing nut for the air dryer?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 6,927 Answers

Most of the time there is not a body nut on them,there is a threaded hole for the screw.You can get a sheet metal screw with a hex head and use it instead.

Posted on Jul 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Are the bolts to remove the front rotors on a 2004 mitsubishi endeavor reverse threaded


never seen left handed threads on a brake disk ,use a impact driver as they are tight to remove and if that doesnt move them drill the head off ,the wheel nuts will hold it all in place ,some cars like fiats do not even have a retaing screw

Mar 23, 2011 | 2004 Mitsubishi Endeavor

1 Answer

1988 Chevrolet Berreta, 6 cylinder. I can't find the Air Filter to it.


from autozone.com
  1. Remove either the wing nut, upper cover retaining bolts or release clips from the upper top of the air cleaner and either lift off or separate the upper air cleaner housing or lid.

0aee193.gif


Fig. Fig. 1: Remove the air cleaner housing lid using a screwdriver ...
8788df2.jpg

Fig. Fig. 2: ... then lift the housing lid up and remove the air cleaner element

  1. Remove the air cleaner element and replace it with a new one.

6406f6f.gif


Fig. Fig. 3: Exploded view of the air cleaner assembly - 2.2L engine shown

  1. Wipe the air cleaner housing out using a damp cloth. Check the lid gasket, if equipped, to ensure that it has a tight seal.

To install:
  1. Position the new element in the air cleaner housing.
  2. Position the lid or housing cover, then tighten the retaining bolts/nut or fasten the clips.

Sep 29, 2010 | 1988 Chevrolet Beretta

1 Answer

How do I take off a starter on a 2000 Chevy S-10?


Disconnect battery cable Ground side, Raise vehical and place jackstands to stabelise, Crawl under vehicals passenger side, remove the 2 bolts on the nose of the starter, and brace on the rear of case if equipped. Push back starter and lower nose first, remove wire retaing nuts, and reverse to reinstall

Jun 11, 2010 | 2000 Chevrolet S-10

1 Answer

Golf mk iv passenger side door wont open from outside


the rod from the handle to the lock has become detached from a broken retaing clip

Mar 11, 2010 | 2003 Volkswagen Jetta TDI

1 Answer

What dose the crank sensor look like and where dose it go on a 99 dodge dokota


Please don't forget to rate!


  1. Remove the air cleaner assembly if necessary for access to the sensor.
  2. Disconnect the pigtail harness from the sensor.
  3. Remove the nut holding the sensor wire clip to the fuel rail mounting stud.
  4. Remove the sensor mounting hardware, then the sensor.
  5. Remove the clip from the sensor wire harness.
To install:
  1. Install the sensor flush against the opening.
  2. Install and tighten the bolts or nuts, as applicable.
  3. Install the electrical connector.
  4. Install the clip on the sensor wire harness.
  5. Install the clip over the fuel rail mounting stud. Install the clip mounting nut.

These 4 pictures are for the Automatic:


672b280.jpg

f025658.jpg

24a1c5a.jpg

These are for a manual trans:


fc2c89c.jpg

41a22c0.jpg

ba33907.jpg

Mar 06, 2010 | 1999 Dodge Dakota

1 Answer

Any tools needed to change the engine air filter in a 2008 Toyota Highlander? Don't see any clips on the box...


Yes, for my 2008 3.5L Highlander, tools were required. First, make sure you get the right replacement engine air filter: there is a different part for the 3.3L and 3.5L engine. Next, as you pointed out, clips aren't used. There are two 10mm nuts that you need to loosen. They are captive (they won't fall out when you loosen them all the way). The one more in the front of the engine compartment is straightforward (once you get a 10mm socket wrench), but the one in the back is in a rather tight spot. I would suggest getting a long (6-8" shaft) 10mm nut driver. I managed to do it with a 10mm socket with a 1/4" drive and some determination. Also note that there is a wiring harness clipped to the top of a sensor adjacent to the air filter compartment; unclip it after you loosen the nuts. It works a little like a phone jack (RJ11) clip or a ethernet (RJ45) clip. Once the nuts are loose and the clip is off you lift up on the large black plastic housing marked 'see owners manual for air cleaner change' or something to that effect. (By the way my owners manual covered NONE of this.) The housing will tilt up and backwards towards the middle of the engine compartment. It won't come all the way off since it is attached to a few other things. Pull out the old filter. While it is out, you may want to wipe out the bottom of the filter compartment if you see any debris.

Note carefully that one corner is a "key"; it makes sure you install the replacement in the right orientation. Look at all four corners of the replacement part; one should look a little different. Toyota helpfully marks the replacement part with UP and FRONT. My Wix replacement had no mark whatsoever. Put the "key" corner on the corner that is more towards the front of the filter compartment and on the right side. Now put the filter cover back on. Note that one of the "hinges" goes into a socket that pops off when you remove the cover. Line that up first, then line up the rest of the cover, especially where the two captive nuts are going to go. While pushing down on the filter cover, tighten the captive nuts.

Oct 13, 2009 | 2008 Toyota Highlander

1 Answer

Cannot get brake light out


YOU REMOVE THE COVER IN THE TRUNK AROUND WHERE THE LATCH IS.THERE SHOULD BE SOME LARGE PLESIC WING NUTS HOLDING THE COVER ON.ONCE THE PANEL IS OFF JUST TWIST THE SOCKET TO REMOVE IT FROM THE LIGHT ,PULL OUT THE BULB.IF YOU NEED THE WHOLE LAMP OUT YOU NEED TO REMOVE THE RETAING BOLTS.

Oct 09, 2009 | Lincoln Cars & Trucks

2 Answers

Gmc jimmy


JACK UP VEHICLE, BLOCCK OTHER WHEELS. REMOVE DIFF. COVER & PLACE VEHICLE IN N. USING A BOX. END 8MM WRENCH; ROTATE DRIVESHAFT TO YOU LOCATE CARRIER RETAINING BOLT ON RH SIDE OF CARRIER. THIS BOLT HOLDS TO RETAING PIN IN CARRIER, APROX. 1/1/4" DIA. REMOVE PIN. PUSH BOTH AXLES INWARD. LOOK INTO CENTER OF CARRIER WHERE AXLES MERGE. EACH AXLE WILL HAVE A RETAING CIRCLIP. REMOVE EACH CLIP & PULL AXLE OUT ABOUT 1 FOOT. REMOVE REAR DRIVESHAFT & SHAFT YOKE @ FORWARD PART OF DIFF. A SPECIAL PULLER IS NEEDED. NOW YOU CAN REMOVE THE 4 BOLTS HOLDING CARRIER TO DIFF HOUSING, PREY OUT CARRIER ASSEMBLY, USE CAUTION- ITS HEAVEY!!

Nov 05, 2008 | 1998 GMC Jimmy

1 Answer

2000 Buick Century air filter


GM hasn't used any wing nuts on their air filter in cars since they switched to fuel injection. It's either going to be several clips or screws holding the air box together. Follow the air duct from throtle body towards air box. It's normally on drivers side. Should be a flat box with the air duct coming out of it.

Sep 12, 2008 | 1999 Buick Century

1 Answer

2000 Expedition Right Ball Joint


you have to get a ball joint seperator, remove the retaing pin, and then the nut, put the seperator between the ball joint and the mount, use a hammer and hit the end of the seperator with the hammer, this will pop it loose, then take a large crow bar and push down on the control arm, this will free it from the arm... use a drill with a 1/2" bit to drill the rivets out of the top of the ball joint....

the new ball joint with come with nuts and bolts to bolt the new one down....

slide the ball joint back into the arm, and put the nut on and tighten as much as you can, then replace the retaining pin.....

Jun 14, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
1994 GMC Suburban Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...