Question about 2000 Pontiac Montana

1 Answer

Just installed new rotors,brake pads, bearings and tie rods to front of 2000 montana. have a whopping sound when driving , this goes away when wheels turned slightly right. when turning right corner hear a clicking sound, what could this be

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Pontiac Master
  • 3,854 Answers

One of your CV joints are bad, inspect which CV joint needs to be replaced. Roll your windows down and make tight right and left corners in an empty parking lot slowly and listen for the clicking noise. If it's coming from the passenger side window or the drivers side window, which ever side the noise is coming from is the side that the CV joint has failed and will need to be replaced.
Thank you for using FIxya and replacing the front wheel bearing improperly buy hammering the CV joint out instead of using a wheel bearing puller will cause damage to the CV joint as to what you have described. Good luck and keep us posted.

Posted on Jul 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clunking noise when braking on a 2000 pontiac montana. I have replaced the outer tie rods right axle and both front hub assemblies


It may be a loose suspension part (struts, sway bar, etc.), but I would take a close look at the brake calipers - the pads inside and outside of the rotors are slightly different and must be installed correctly, and any pad vibration clips must also be installed correctly. Also make sure the axle nut and wheel lug nuts are torqued correctly.

Mar 27, 2018 | Pontiac Cars & Trucks

1 Answer

I have a 2000 pontiac montana that i notice a small clunking noise when applying the brakes.I just replaced the outer tie rod ends and right axle along with both front hub assemblies


Is the run out on the brake rotors within specs and are the brake pads fitted tightly in their mounts and high temp synthetic brake lube been applied behind each brake pad?
Also the wheel nut torque needs to be correct tightness so the rotor does not move on the wheel studs.

Mar 27, 2018 | Pontiac Cars & Trucks

3 Answers

Vehicle shimmies when brakes are applied


Loose tie rods that is what my problem was when my car did that. What happens is when you apply the brakes the tie rods move in and out

May 27, 2016 | 2000 Chrysler 300M

2 Answers

I had a front wheel bearing fail. I want to repair the vehicle and make it reliable. It has approximately 180,000 miles on it.


Sounds like you have it all.Plus have the front end aligned after you install everything.Also check air pressure in tires.

May 25, 2015 | 1998 Dodge Durango

2 Answers

I have a 1994 chevey exstended cab 4 wheel drive it has a vibration in front it seems kije uts there when i accelerate then it kinda goes away but then when i brake and slow down it vibrates worst


sounds like you have a warpped brake rotor, bad ball joint, or a bad tire. I would recommed taking the truck to a tire shop and have them shake down the front end that will tell you if its a tire or ball joint

Mar 01, 2011 | 1999 Chevrolet Silverado 1500

2 Answers

Newly installed brake rotors and pads. balanced wheels, but still shakes when brakes are applied. I can also feel the shaking on the steering wheel when driving on rough road.


Apply the emergency brake slightly while driving to see if the rear brakes are the issue. Other wise the rotors are warped or there is debris behind the rotor to hub surface

Feb 06, 2010 | 2004 Toyota Camry

2 Answers

When I press on the brakes the car shakes a little, I can feel it in the steering wheel.


The front brake rotors are warped. Have front brakes checked and see how much pad is left. Some shops will offer to "turn the rotors". This means they will machine them. This is a quick fix. For the correct way is to replace them. Be careful where they get there rotors from. A cheaper auto parts store may carry them for less, but can also come warped from the manufacture. I would chose NAPA auto parts. I have better luck with them.

Jan 20, 2010 | 1998 Pontiac Grand Prix

3 Answers

2000 caravan drivers side rotor wears out told tie-rod true or no


Look behind front wheel for rod that attaches to spindle/knuckle, and moves your wheel back & forth from steering rack. The tie rod (outer) is the piece attached on the end, that is threaded on that rod, and attaches to the spindle/knuckle, behind the wheel. Grab your tire and try to wiggle it hard from side to side. (hands at 3 & 9 o'clock ) Push with one hand while pulling with the other. If there is slop, or play, you have probably got a bad tie rod end, which you can observe it move by looking at where it attaches, while someone else wiggles it. Maybe this picture will help you I.D. it.498e60a.jpg

Jul 29, 2009 | 1988 Dodge Grand Caravan

5 Answers

The front end shakes when i hit the brakes when i am driving over 60 miles an hour


Hellos your front rotors are warped and uneven have them turned to true them up this will fix your problem.:)

Jul 22, 2009 | 2006 Pontiac G6

1 Answer

I have a bad wheel bearing how do I replace it


Hub and Bearing Assembly
ani_caut.gif CAUTION: Do not begin this removal procedure unless the following parts are available:
  • A new front axle wheel hub retainer (3B477) (Step 1).
  • A new inboard halfshaft joint stub shaft circlip.
Once removed, these parts must not be reused during assembly. Their torque holding ability or retention capability is diminished during removal.

Removal
  1. Turn ignition switch to the OFF position and place the steering column in the unlock position.
  1. ani_caut.gif CAUTION: Discard the front axle wheel hub retainer. It is a torque prevailing design and cannot be reused. If loosened, the retainer must be removed and a new one installed.
    Remove and discard front axle wheel hub retainer (3B477).
  1. Raise vehicle on hoist.
  1. NOTE: Make sure steering column is in the unlocked position, and do not use a hammer to separate tie rod end (3A130) from the front wheel knuckle (3K185) . Use extreme care not to damage boot seal.

    Remove cotter pin from tie rod end stud and remove slotted nut. Discard cotter pin and nut.
  1. Using Tie Rod End Remover 211-001 (TOOL-3290-D) or equivalent and Tie Rod End Remover Adapter 211-087 (T81P-3504-W), remove tie rod end from front wheel knuckle.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to remove the nut, or bearing and seal damage will result. Loosen the nut first, then remove nut from stud using the hex hold feature.
    For SHO vehicles, remove vinyl cover from upper link stud.
    Remove stabilizer bar link (5K484) from front shock absorber (18124) .
  1. Remove disc brake caliper (2B120) and support with wire to obtain working space. Do not allow disc brake caliper to separate from the front disc brake caliper anchor plate (2B292) to prevent contamination of the disc brake guide pin journals. Do not allow disc brake caliper to hang from front brake hose (2078) . Remove front disc brake rotor (1125) . Remove front disc brake rotor from wheel hub (1104) by pulling it off the lug bolt (1107). If front disc brake rotor is difficult to remove from front wheel knuckle , strike front disc brake rotor sharply between lug bolt with a rubber or plastic hammer.
    If front disc brake rotor will not pull off, apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to inboard and outboard rotor/hub mating surfaces. Install 3-Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor by pulling on front disc brake rotor outside diameter and pushing on hub center. If excessive force is required for removal, check front disc brake rotor for lateral runout prior to installation. Refer to Section 06-00.
  1. Remove anti-lock brake sensor mounting bolt and front brake anti-lock sensor (2C204) .
  1. Remove and discard lower ball joint nut. Using Remover Adapter 211-211 (T96P-3010-A1), separate lower ball joint from front suspension lower arm (3078) .
  1. Using Rotunda Spring Compressor 014-00781 or equivalent, compress front coil spring (5310) until lower ball joint clears front suspension lower arm .
  1. Using Front Hub Remover/Replacer 204-069 (T81P-1104-C), Two Stud Adapter 205-237 (T86P-1104-A1), Metric Hub Remover Adapter 204-085 (T83P-1104-BH) and Front Hub Installer 204-067 (T81P-1104-A), press front wheel driveshaft joint (3B414) from wheel hub . Wire front wheel driveshaft joint to body to maintain a level position.


    df1570a.gif


    Item Part Number Description 1 204-085 (T83P-1104-BH) Metric Hub Remover Adapter 2 204-067 (T81P-1104-A) Front Hub Replacer 3 — Turn Wrench Counterclockwise 4 — Hold Wrench Stationary While Turning Other Wrench 5 204-069 (T81P-1104-C) Front Hub Remover/Replacer 6 204-067 (T81P-1104-A)1 Two Stud Adapter A — Make Sure Metric Hub Remover Adapter 204-085 (T83P-1104-BH) is Fully Threaded onto 1107 and is Positioned Opposite the Two Stud Adapter 205-237 (T86P-1104-A1)
  1. Remove and discard three hub and bearing retainer bolts from front wheel knuckle .
  1. NOTE: Wheel hub is not pressed into front wheel knuckle . Do not use slide hammer to remove a stuck wheel hub . Do not strike back of inner bearing race. Use of these methods will damage bearing internal parts.

    NOTE: If bearing carrier is corroded to front wheel knuckle , apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to the inboard and outboard wheel hub/knuckle mating surface and allow to soak.

    Remove wheel hub from front wheel knuckle .


    f8656a.gif

Installation
  1. NOTE: If wheel hub is damaged or if any end play is detectable, replace wheel hub . End play is not adjustable. If wheel hub is disassembled, the assembly must be replaced.

    Remove all foreign material from knuckle bearing bore for correct seating of new wheel hub.
  1. Lightly lubricate mating surfaces of bearing corner and front wheel knuckle.
  1. ani_caut.gif CAUTION: Knuckle bore must be clean enough to allow wheel hub to be completely seated by hand. Do not press or draw wheel hub into place.
    Position wheel hub in front wheel knuckle . Install three new hub and bearing retaining bolts. Tighten to 83-107 Nm (61-78 lb-ft).
  1. Push front wheel driveshaft joint into wheel hub . Hand start front wheel hub retainer.
  1. Slowly release Rotunda Spring Compressor 014-00781 or equivalent while guiding lower ball joint into front suspension lower arm .
  1. Install new lower ball joint nut. Tighten to 68-92 Nm (50-67 lb-ft).
  1. Install tie rod end into front wheel knuckle . Install new slotted nut and tighten to 47-63 Nm (35-46 lb-ft). If necessary advance nut to install a new cotter pin.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber . Install stabilizer bar link nut. Tighten to 77-103 Nm (57-75 lb-ft). For SHO vehicles, install stud cover.
  1. NOTE: Remove rust from the rotor and hub mating surfaces with a medium abrasive pad.

    Install front disc brake rotor and disc brake caliper . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: The front axle wheel hub retainer must be tightened to specification immediately during installation. If the retainer is not tightened immediately, the nylon lock will set incorrectly, leading to incorrect torque readings and bearing failure. Any front wheel hub retainer that is not immediately tightened to specification or is loosened must be removed and a new retainer installed.
    Install front axle wheel hub retainer . Tighten to 230-275 Nm (170-203 lb-ft).
  1. Install wheel and tire. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.

May 28, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
2000 Pontiac Montana Logo

440 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...