Question about 2004 Nissan Murano
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Front struts replacement
Jack up and secure front end of your vehicle,Take off two front wheels. Loosen to bolt on the bottom of struts (Its a bolt and nut). Remove clip that holds brake hose on to strut and remove hose. DO NOT OPEN BRAKE LINE OR DISCONNECT FROM CALIPER. Remove bolts and remove bottom of strut from knuckle/Hub assembly. Then loosen nuts on strut tower( on top of fender inside hood) (3) nuts, mark exact locations of each nut on strut mount area on upper fender weld. Make sure to hold strut on the bottom so it doesn't drop down on caliper and knuckle or on you possibly.YOU WILL NEED A SPRING COMPRESSOR to compress spring so you can take struts off. MAKE SURE THAT SPRING IN COMPRESSED/SQUEEZED WITH A STRUT COMPRESSOR. Then loose center nut on strut tower(may be covered with a circular rubber cover) If nut spin around with out getting loose use vise grips to hold strut rod ONLY TO REMOVE STRUT NOT TO INSTALL. if you use vise grips to install it will damage strut. When nut is off, remove strut and reinstall new one transfer all rubber boots and cushions from old strut. Good Luck thanks for using FIX-YA.com contact me if you need more help.
Posted on Dec 30, 2008
SOURCE: 2004 nissan maxima
Take a look at your gausett brackets, by the front exhaust tube. 2 sheet metal lookig brackets, each held up by 2 screws each. Those gausetts brake and cause a rattle, Common problem on a MAxima your year. Nissan has a TSB for replacement of these brackets.
Posted on Jul 26, 2008
WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....
Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...
you all enjoy your rides out htere!!!
Posted on Jul 01, 2009
remove screws - they is probably one around the door handle (carefully pry out cover piece) - and underneath any big round (1 inch diameter) plastic screw hole cover - then carefully pry off.
Posted on Feb 05, 2010
Tips for a great answer:
on Mar 23, 2012 | 2004 Nissan Maxima
Jul 20, 2014 | 2004 Nissan Maxima
Jun 01, 2011 | 2004 Nissan Maxima
Dec 01, 2010 | 2004 Nissan Maxima
Apr 22, 2010 | 1997 Nissan Maxima
Sep 11, 2009 | 2005 Nissan Maxima
Dec 30, 2008 | 2004 Nissan Altima
331 people viewed this question
Usually answered in minutes!