Question about 1989 Isuzu Trooper

Open Question

Clutch 98 petrol jack aroo needs replacing how

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace the altinator in a2007 Suzuki reno


wow, you want super basic service questions. even placement.
what country
which engine, ?
1.4 L E-TEC I4 (petrol)
1.6 L E-TEC I4 (petrol)
1.8 L Family II I4 (petrol)
2.0 L Family II I4 (petrol)
2.0 L RA 420 I4 (diesel)

try reading the manual.
pull the battery negative lug first. or boom.
I will never tell you how to jack a car ,not me.... read a book first.
read the FSM pages on Safety.....

https://suzukipitstopplus.com/Products/1068-2007-forenza-reno-service-manual.aspx


the steps are the same on all cars.
only access to ALT varies.
all cars made.
  1. neg lug off
  2. gain access
  3. unbolt wires at alt
  4. release belt
  5. unbolt alt.
the FSM may tell you the best way to gain access.

no engine stated, so I pass on details.

Oct 08, 2014 | 2007 Suzuki Reno Hatchback

1 Answer

Nissan Patrol 98 petrol valve clearance


hi, i have a nissan patrol st4500 running on gas and petrol and I need a new valve since it has been bad to switch between gas and petrol, do any of you know where I can order it?

Mar 30, 2012 | Cars & Trucks

1 Answer

98 jetta wolfsburg. Clip that hold cable to arm broke. When replacing the clip I had to jack up the clutch arm with a bottle jack to hook up the cable. The cable will not let the arm drop down where it...


It has a plastic Ratchet style gear at the pedal end of the cable that has to be released. This gear automatically adjust the clutch when the pedal is pressed. Never put a jack against a clutch arm. You will probably have to disengage the cable to reset the ratchet gear. Don't strip the teeth on the gear

Jul 17, 2017 | 1998 Volkswagen Jetta

1 Answer

WHEN REPLACING THE CLUTCH ON AN AUDI 1.8 PETROL A4 ESTATE CAR IS THERE ANY NEED TO REPLACE THE FLYWHEEL


I routinely have replaced the flywheel,rear main engine seal, pilot bearing,and input shaft bearing as well as the clutch , pressure plate and throw out bearing,in the last 30 years and have not had a come back.

Jul 19, 2010 | 1999 Audi A4

1 Answer

I need to know how to get the starter motor of a 98 prado


I'm not familiar with that particular vehicle, but you may have to disconnect one of your motor mounts and jack the engine, or remove your exhaust from one side. Be creative, I have faith in you. If you do have to jack the engine, be sure you don't damage the oil pan or other components. Also make sure that it can't fall before you get your digits in harms way.

Feb 17, 2010 | 1998 Toyota Land Cruiser

1 Answer

2002 2.0L Passat petrol: Clutch biting point problem


your pressure plate is damaged.Replace cutch asseberly

Jun 12, 2009 | 2002 Volkswagen Passat

1 Answer

98 XJ8L Fuel Filter replacement


The fillter is above the rear axle and is one of these jobs where the petrol runs up youer sleeve   not easy  D

Jan 19, 2009 | 1998 Jaguar XJ8L

1 Answer

Replaced clutch but pedal will not move down at all now on 98 chevy 1/2 ton 2wd


Sounds like the release bearing is in backwards! No check valve. If the peddle was pushed, it would pop the slave cylinder piston. 2/ The clutch disc could be in backwards too! Either way, you will need to pull the tranny! Sorry! Frankster016

Oct 22, 2008 | 1998 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

83083 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14509 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...