Question about 1995 Chevrolet Lumina

Open Question

How many motor mounts on the 1995 lummina? - 1995 Chevrolet Lumina

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram for a 1995 ford winstar van 3.8l for motor mounts


Unfortunately, it doesnt really give any information on removing / installing the engine mounts other than to raise and support the engine assembly with a suitable device and then unbolt and remove the engine mounts... Hope this helps9_8_2012_9_22_00_pm.gif

Sep 07, 2012 | Ford Windstar Cars & Trucks

1 Answer

REMOVE REAR MOTOR MOUNT ON 1995 MAZDA PROTEGE


to remove that support is recommended to use keys of extensions to be used by the top and back of the engine,,,recommended to release the air filter and battery sleeve for space

Apr 11, 2012 | Mazda Cars & Trucks

1 Answer

Can't find a motor mount


Your engine sets on motor mounts and then the motor mounts set on the frame. There are also some motor mounts in the front of the car that attach to the frame with a rubber housing and big bolts running through them. Usually in the middle of the engine.

Dec 14, 2010 | 1995 Saturn Sc

1 Answer

Removal of oil pan for chevy lumina 1995


You must raise then engine high enough to remove the oil pan. Loosen motor mount bolts & remove them, jack engine up enough to remove pan or use a chain block. Use wood blocks to support engine at motor mounts. Good luck!

Apr 04, 2010 | 1995 Chevrolet Lumina

1 Answer

Do i have to disconnect motor mount to replace my drive belt


Depends on the motor. If there is a mount on the passanger side that the belt goes around then yes. Don't fret though, easy to get around. Use a jack and a piece of wood on the oil pan to support the motor so you can remove the motor mount to remove the belt. Again, this is on SOME gm motors not all. On the others the mount isn't in the way at all.

Jan 24, 2010 | 1995 Pontiac Bonneville

1 Answer

Putting on a transmission filter kit


to replace filter jack up and support vehicle if has drain plug remove and drain or loosen and remove all bolts but keep the two corner bolts at the front loose but not out and one in the middle opposite side at back have big pan under wider than trans pan pry at single bolt to release gasket when released remove single bolt let drain than remove other bolts clean pan and gasket put aside grab filter and pull down make sure o ring is removed not stuck up in tube replace filter /o ring reassemble and tighten bolts in crisscross pattern

Oct 13, 2009 | 1995 Chevrolet Lumina

1 Answer

Motor mounts in nissan not lineing up


I had to pry the mounts foward by lifting the motor, slideing a short screwdriver in the guide holes then drop the motor. Worked ok but still not shure if that is normal for them to have so much tention.

Jun 13, 2009 | 1995 Nissan 300ZX

1 Answer

1995 Taurus motor mounts


these are known as cradle bushings. the frame around engine is called the cradle. you can get mounts from ford should just replace these and be fine

Oct 16, 2008 | 1995 Ford Taurus

Not finding what you are looking for?
1995 Chevrolet Lumina Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...