Question about 2004 Volvo V70

1 Answer

How do I reset the service required on my display?

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Close all doors
Turn ignition key to position I
Press

Posted on Sep 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just had my rear brake pads & sensors replaced. How do I get the light off ( reset) ?


You can not simply reset the light, you have to actually replace the brake sensor wire that connects to the rear brakes. This is a sensor that is worn through, when the brakes get low, the sensor rubs the rotor and breaks the connection, turning on the light. You need to get a new sensor from a dealer and replace the brakes and sensor together to get the light off.

After replacing the wire as stated do the following to reset the light and mileage countdown timer.


To enter this mode, with ignition on, hold the odo reset button (located on the left side of the instrument panel under the tach) for about 10 seconds.

The center of the info display will change to "service". It will have an icon for which service feature and the miles/date left until service is required. These icons are the same as displayed on the I-drive service screen. So, you can go through the Idrive service screen to get familiar with the icons prior to doing this.


Once in this mode, push the reset button to cycle through the various service items.

To reset a service item that is displayed, hold the reset button. I don't remember how long, but the display will change to a reset mode. You must release the button once it enters this reset mode. Then you will need to confirm the reset by pressing the reset button again.

The reset service interval will then be changed.

You can continue pressing the reset button to scroll through the other icons.

I think to exit, simply shut off the ignition.




Aug 30, 2011 | 2004 BMW 5 Series

Tip

Ford-Lincoln service light 1988-01


LS

2000-01

To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the Message Center, press the STATUS control to access the System Check mode. Press the RESET button to display OIL LIFE _% RESET FOR NEW. Press and hold the RESET button until OIL LIFE IS 100% is displayed.


Mark VIII


1993-97

When "CHANGE OIL SOON" or "OIL CHANGE REQUIRED" is displayed on the Message Center, turn the ignition on. Press and hold "OIL CHANGE RESET' or the "RESET" button until "OIL LIFE RESET TO 100%" is displayed on the Message Center.


Continental


1989-94

When "SERVICE" is illuminated, on the Message Center, press the "SYSTEM CHECK" button on the right of the display. Then press the "RESET" button. The "SERVICE" symbol and mileage will start to flash. Next, press the "SYSTEM CHECK" and "RESET" buttons at the same time. The display will show "7,200 miles/11,580 km" and will count down from there as long as the buttons are depressed. Release the buttons at the desired service interval.


Continental


1988

When "SERVICE DUE" is illuminated on the Message Center, press the "CHECK OUT" button located below the display. Then press the "RESET" button. The display should now read "SERVICE DONE?" Next, press the "CHECK OUT" button and "RESET" buttons at the same time. The display will show "7,200 miles/11,580 km" and will count down from there as long as the buttons are depressed. Release the buttons at the desired service interval.







on Dec 07, 2009 | Ford Lincoln Continental Cars & Trucks

Tip

Ford service light procedure 1994-01


Windstar

1999-01

To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the message center, press the SETUP control to access the System Check mode. Press and release the RESET button until IF NEW OIL HOLD RESET is displayed. Press and hold RESET button until OIL LIFE SET TO 100% is displayed.


Windstar


1997-98

To reset "CHANGE OIL SOON/OIL CHANGE REQUIRED" message on the Message Center, press "RESET" and "SETUP" controls at the same time. "OIL LIFE % HOLD RESET NEW" will be displayed. Press the "SETUP" control to access the System Check mode. Press "RESET" to start the system check. Press and hold the "RESET" control. Press "RESET" and "SETUP" to reset the system to 100%


Explorer,
Mercury
Mountaineer


1997-01

To reset the oil life feature on the Message Center, press and hold the "OIL CHANGE RESET" button until the system counts down (about 5 seconds). The Message Center will display "OIL LIFE RESET TO 100%"


Probe

with Analog Dash

1989-92

When "SERVICE" is illuminated on the Vehicle Maintenance Monitor on the overhead console, press the "SERVICE INTERVAL RESET" button located directly above the light.


Probe

with Digital Dash

1989-92

When "SERVICE" is illuminated on the Vehicle Maintenance Monitor on the overhead console, press the "SERVICE INTERVAL RESET" button located directly above the light.


Probe

with Digital Dash

1989-92

When "SERVICE INTERVAL CHECK" is displayed is displayed on the far left side of the instrument panel, press the "SERV OFF" button, located on the speed alarm keyboard, until three tones sound.


Thunderbird,
Mercury Cougar

with System Scanner

1986-88

When "SERVICE" appears on the Diagnostic System Scanner, press the "ODO SEL" and "TRIP RESET" buttons simultaneously. The "SERVICE" message will go out and three short beeps will be heard when the system is reset.


Thunderbird,
Mercury Cougar


1989-94

If "CHANGE OIL SOON" or "NOW" is indicated on the Monitor, turn the ignition on, but do not start the engine. Within 16 seconds, insert a paper clip into the cavity to the left of the display and depress. The display will flash; when it stops, the system is reset.















on Dec 07, 2009 | Ford Windstar Cars & Trucks

2 Answers

How can you reset the service light on a vauxhall corsa cdti on a 54 plate


Service reset

tdisline_757.jpg
Important note: Proceed exactly as follows; otherwise the reset system will go into the locked position and special tools are required to unlock it (Tech 2 tester).

1. Turn the ignition OFF.
2. Press and hold the reset button [1] (see the above picture).
3. After 3 seconds the "Distance till service" appears on the display, "InSP 0".
4. Press and hold the brake pedal.
5. Note: Ensure the button [1] is still pressed.
6. Turn the ignition ON.
7. The display shows: "InSP----".
8. After turning the ignition ON, wait for the service message to change and keep the reset button pressed for at least 3 seconds.
9. Release the brake pedal and reset button at the same time.
10. Wait for 10 seconds, until the display shows: "InSP XX,000 km".
11. The system is reset.

Jul 15, 2011 | Volkswagen New Passat Cars & Trucks

1 Answer

How to reset service light


I think the following will work:

1 . Insert key into ignition barrel.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched 'ON'. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message 'RESETTING SERVICE MODE'.
9 . Keep both buttons pressed until the warning message changes to 'SERVICE MODE RESET' (after ten seconds).
10 . Once the message is displayed the buttons may be released â€" sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to 'Off' and then back to Ignition position II and check that the message is no longer displayed.

Jul 12, 2011 | 2005 Jaguar S-Type

3 Answers

How do you reset the oil change required after oil change on a 2007 ford explorer sport trac limited?


Depending on your cluster its one of these...


Message Center Configuration
Oil Life Reset - Message Center Cluster

NOTE: The oil life calculation is set at a maximum of approximately 8,000 km (5,000 miles) or 180 days

  1. Press and release the SETUP button until the message center displays PRESS RESET TO BEGIN SYSTEM CHECK.
  2. Press and release the RESET button until the message center displays HOLD RESET IF NEW OIL.
  3. Press and hold the RESET button for 2 seconds and release to reset the oil life to 100%.
  4. The message center displays SETUP MENU HOLD RESET.
Oil Life Reset - Base Instrument Cluster

NOTE: The oil life calculation is set at a maximum of approximately 8,000 km (5,000 miles) or 180 days.

  1. Place the ignition in the RUN position with the engine off (KOEO).
  2. Press and release the TRIP/RESET button until SETUP MENU HOLD RESET is displayed.
  3. Press and hold the TRIP/RESET button until SYSTEM CHECK is displayed.
  4. Release the TRIP/RESET button.
  5. Press and release the TRIP/RESET button to scroll through the system check menu items until HOLD RESET IF NEW OIL is displayed.
  6. Press and hold the TRIP/RESET button until OIL LIFE SET TO 100% is displayed.
  7. Release the TRIP/RESET button. The oil life is now reset.
Oil Life Start Value - Message Center Cluster

NOTE: The oil life start value is used to reset the oil life value back to the maximum of approximately 8,000 km (5,000 miles) if the value was previously changed or to lower the value from the maximum (8,000 km
To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following:
  1. Enter SYSTEM CHECK to display "OIL XXX% OIL LIFE OK".
  2. Press RESET control to display "HOLD RESET IF NEW OIL".
  3. Press and hold RESET control for more than 2 seconds. Oil life is set to 100% and "OIL CHANGE SET TO 100%" is displayed

Mar 06, 2011 | 2007 Ford Explorer Sport Trac

2 Answers

How to reset maintenance required light on dash


Instructions
  1. 1 Turn on the engine.
  2. 2 On the vehicle's dash, press the "Step" button until "Miles to Service" is displayed.
  3. 3 Press and hold the "Reset" button, near the "Step" button, until the "Miles to Service" flashes and resets.
  4. 4 Verify the "Perform Service" light goes away.

Feb 14, 2011 | 2003 Jeep Liberty

1 Answer

When you car is displaying engine system service required, what will one do?


The car computer keeps track of the number of kms/miles that was done since the last service when this light and counter was reset: according to the car computer mileage log, the car is now due for its next 'regular' service: take it to a garaged for its overdue service and they will reset the warning.

Hope it helps.

Oct 04, 2010 | 2004 Volvo C70

1 Answer

I have serviced my 06 dodge caravan, how do i reset the service required light


turn key on with engine off.
press menu button until service interval is shown
then scroll using the step button until preform service is displayed
then hit yes.

Apr 01, 2010 | 2006 Dodge Durango

2 Answers

Yellow/gold wrench is illuminated on dash board


Please note:

Honda makes reference to proper vehicle maintenance in their service/user manual. Consult your authorized Honda dealer before doing anything that may void your vehicle warranty.

https://techinfo.honda.com/rjanisis/pubs/om/AC0606/AC0606O00192A.pdf

Owner's Manual page 193-197.

Resetting the Engine Oil Life
Indicator

Your dealer will reset the display
after completing the required
maintenance service. You will see
‘‘OIL LIFE 100 %’’ on the odometer/
trip meter display the next time you
turn the ignition switch to the ON
(II) position.

If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
follows:

1. Turn the ignition switch to the ON
(II) position.

2. Press the Select/Reset knob until
the engine oil life indicator is
displayed.

3. Press the Select/Reset knob for
more than 10 seconds. The engine
oil life indicator and the
maintenance item code(s) will
blink.

4. Press the Select/Reset knob for
more than 5 seconds. The
maintenance items code(s) will
disappear, and the engine oil life
will reset to ‘‘100.’’

Important Maintenance
Precautions

If you have the required service
done but do not reset the display, or
reset the display without doing the
service, the system will not show the
proper maintenance intervals. This
can lead to seriousmechanical
problems because you will no longer
have an accurate record of when
maintenance is needed.
Your authorized Honda dealer
knows your vehicle best and can
provide competent, efficient service.
However, service at a dealer is not
mandatory to keep your warranties
in effect. Maintenance may be done
by any qualified service facility or
person who is skilled in this type of
automotive service. Make sure to
have the service facility or person
reset the display as previously
described. Keep all receipts as proof
of completion, and have the person
who does the work fill out the
maintenance record. Check your
warranty booklet for more
information.

Information obtained from:

https://techinfo.honda.com/rjanisis/RJAAI001_OMANUAL.ASP?YEAR=2006

If the information provided to you was useful, please rate my response.

Thanks,

OpenSource13

Apr 19, 2009 | 2006 Honda Accord

Not finding what you are looking for?
2004 Volvo V70 Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

Marvin
Marvin

Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...