Question about 1988 Volvo 240

1 Answer

My front swing bearing holding the drive shaft needs replacing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volvo Master
  • 2,019 Answers

All the parts you need are easily found on the internet, for very low cost.

http://www.swedishautoparts.com/240/volvo-240-driveshaft-and-axle-parts.html

You should probably consider also doing the u-joint, flex coupling, support bushing, and spring as well, since they are all inexpensive.

Posted on Jul 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Dodge Dakota SLT ext cab 3.9 V6. How to remove drive shaft? Has a double shaft with a bearing in the middle. Bearing has a square frame around it.Has 3 u-joints on the drive shaft.


The shaft is removed in one piece. You first locate the two bolts that hold the center bearing assembly to its cross brace and remove them. Then, you go to the rear differential and remove the two straps holding the rear u-joint to the pinion shaft. Once you remove the rear u-joint from the pinion shaft, tape the loose end caps in place to prevent loss. Now you can slide the driveshaft to the rear, disengaging it from the transmission in front. You may want two people to do this as you need to avoid allowing the front yoke of the driveshaft to slam into the ground. Installation is the inverse of removal.

Nov 12, 2016 | 1996 Dodge Dakota

1 Answer

Is it possible to remove and replace front wheel bearings with out a press


In order to remove the front wheel bearings without press hub off the bearing and then the bearing out of the knuckle. To do the first step need a a Support Bridge.It is a special tool. Make bridge and use a general bearing pulled kit to replace bearings. use a "Front Wheel Drive Bearing Removal Adapters Puller Pulley Tool Set Kit" .To replace the bearing, remove front CV shaft taking care not to move the CV shaft too far out .

Nov 06, 2015 | 2002 Kia Rio

1 Answer

Front diff.seal leaks


Remove the front drive shaft remove the drive yoke off the pinion shaft remove the old seal install new seal install front drive shaft. PS check pinion bearing play before removing drive yolk. if it is loose then you might also need bearings

Oct 21, 2015 | Ford Explorer Cars & Trucks

2 Answers

2002 mercury mountaineer suv 2002 noise clicking when backing up


if this is a 4wd drive model , try having someone listen to front wheel hubs when you back up , id be conserned that the front wheel hubs seals have gone bad and there is now dirt inside bearings and has damaged them , also ive seen clicking caused by locking hubs not fully disengauged by dirt stuck inside

Aug 30, 2014 | 2002 Mercury Mountaineer

1 Answer

It is 2 wheel drive and is the drive shaft it has wheel bearing support is 2 part drive shaft and the noise is after 55 like every second like scraping noise


It can be a u joint,or the drive shaft bearing,some call it drive shaft support bearing,or swing bearing.Moving the drive shaft up,and down should tell you if the swing bearing is bad,it should not have no movement up,or down,or side to side.It should stay centered in the housing,surrounded by rubber.

Nov 21, 2009 | 2002 Chevrolet S-10

2 Answers

How to replace front u joints 2001 suburban?


if its 4wd drop front drive shaft remove the clips that hold the ujoints in place use a socket or a punch about the size of ujoint cap put in vise and knock out the old joint and replace with new one careful not to hurt needle bearings in the caps. if it is rear wheel drive and two piece driveshaft undo the the shaft at rearend and undo the center support bearing in the middle of the two shafts and pull out of vehicle replace ujoints same way as above. if it does not have the clips holding caps it plastic seal which needs to be heated up until the plastinc runs out of hole in flange

Aug 30, 2009 | 2001 Chevrolet Suburban

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

1 Answer

Chey aveo front hub bearing what is this?


yes front wheen drives have hub bearings. Most of them need the hubs to be pressed apart to replace them. the hub bearing supports the end of the CV drive shaft closest to the wheel. hope that helps.

Mar 17, 2009 | 2004 Chevrolet Aveo

1 Answer

Bearing on 4WD front differntial drive shaft yoke


In short yes, the bearing is pressed on the pinion gear, the only way it will come out is to remove cover on housing and pull carrier with ring gear out, and also yoke that drive shaft bolts to, then pinion will come out, there is also a crush sleve that will have to be replaced when it goes back together it goes over the pinion gear, thats for backlash ajustment when you tighten the pinion back in the housing. if you plan on doing this yourself you will also need a dial indicater to set the backlash. If you want my advise take it to a shop to have it done, if you don't get it right it could end up costing you alot more than if you took it someware and had it done.

Feb 03, 2009 | 1999 Chevrolet K1500

1 Answer

Replacing front wheel bearing


The brake rotor needs to be removed, drive shaft nut in center of hub then 3 bolts hold the hub assembly to spindle from back side. if it has abs unplug it then some work will need to be done with a hammer and chisel to work the bearing out of spindle and axle shaft from bearing

Oct 16, 2008 | 2001 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...