Question about 2008 Toyota Camry

1 Answer

I bought a seat cover for the backseat of my 2010 camry but i cannot figure out how to get the seat out. please help me thank you in advance for your time. Gloria j Beverburg

Posted by on

  • gjcarrigan Jul 19, 2010

    you are the best. thank you so much, Gloria



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Toyota Master
  • 81,400 Answers

Are u trying to remove the whole seat assmbly or just the seat back upright? is this a factory replacement cover, please clarify.

Posted on Jul 19, 2010

  • 1 more comment 
  • gjcarrigan Jul 19, 2010

    i have the back part in place it is the bench seat that I can't figure out how to remove so i can get all

    the straps and buckles in place so it will be secure.

  • Marvin
    Marvin Jul 19, 2010

    the seat is bolted to the floor, one bolt at front and back side on each side of seat, just remove the trim covers over the bolts and then remove the bolts or nuts (some seats set on studs with a nut and some are bolts) This really easy.

  • gjcarrigan Jul 19, 2010

    thank you for your time and i will sure give it a try. thanks again, Gloria



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I lower the backseats in my 2005 Cadillac SRX so they lay flat

Could be a switch under or around the trimming of the seat. if you cant figure it out take it to the dealer they will be happy to help you.

Sep 21, 2014 | 2005 Cadillac SRX

1 Answer

I have a 1961 corvair and I am trying to figure out how to lift up the backseat

Most cars of that era, have two latches for the bottom of the seat usually about 1/4 distance from the edge of the seat. You push down and back on the front edge of the seat and it unlatches.then lifts out. The seat back usually has two tabs or sometimes bolts that you can get to when the bottom of the seat is removed.

If you need further help, reach me via phone at

Jan 12, 2014 | Cars & Trucks

2 Answers

05 equinox wet carpet(backseat)and flooded tire well

i have had this same problem on my 05, you need to check your "cabin pressure release valve cover" its located below the driver side tail light underneath the bumper. so if you look directly underneath the light laying on the ground you can run your hand up the bumper and feel it, its a rectangle hole. i had to go the dealership to have them identify it for me. but thats is where my water leak was coming in from.
i'm assuming with wear and tear after 4-5 years of road it probally cracked and gave out and is letting water in through there. this has been verified by me as well.

Jan 03, 2010 | 2005 Chevrolet Equinox

1 Answer

I want to replace my middle backseat belt. How can I fold the seat or get to it?

I believe the rear seat backs fold down in this model. Fold them down and the bolts should be visible

Sep 10, 2009 | 1991 Toyota Camry

1 Answer

Looking for lost necklace in rear seat of 2010 Camry

to take off the the bottom part of the seat all you have to do is pull the front seats up all the way get in the back seat push the front of the back seat back and pull up

Jul 08, 2009 | 2008 Toyota Camry

1 Answer

How to remove backseat backrest to change seat cover from 05 f150

u have to start by taking the bottoms out. then the back there should be two bolt to take out and it slides up and pulls off

Jun 15, 2009 | 2005 Ford F-150

1 Answer

Lay down backseat in Crown Vic Police Interceptor

The backseats of this vehicle do not fold down. They are placed on hooks and then they're bolted in on the bottom right and bottom left of the seat.

Jan 10, 2009 | 2001 Ford Crown Victoria

1 Answer


First focus on making sure that the seat is appropriate for your child and has done well in crash tests. Car seats are meant to fit in just about every car although if you have a small backseat you may just need to squish it in more. The type of car you have really shouldnt matter

May 18, 2008 | 2007 Infiniti Fx

Not finding what you are looking for?
2008 Toyota Camry Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides