Question about Dodge Dakota

1 Answer

I need to know how you relearn a new computer. the box that it came in says that you have to relearn it before you can use it?! i dont know but ive been trying to figure it out all day!! is there anyway you can help me with this information? and i also need a diagram of a 89 dodge dakota engine and motor can not find one anywhere!!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 447 Answers

Well, they might mean one thing or another when they say "relearn" depending on the year of the vehicle. If this is about a 94 model or later what they may mean is that it needs to be programmed by a shop that has the ability to do so before it will work in your vehicle and it may not even be able to start the engine before that has been done to it. Prior to 94 what they may mean is that idle speed and fuel control parameters need to be relearned by the computer as you are driving it for best performance and that the engine may run a bit poorly until the computer does this [it does this by itselft based on engine conditions and how you drive] If the vehicle starts, runs normally, and the "check engine" lamp is off it probably doesn't need any programming. Hope this helps a bit and good luck!

Posted on Jul 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ford falcon xr6 au tickford series 3 2003 wont start


Check if you have a main fusible link which is a wire that is suppose to melt to prevent the smaller relays from damage. It would be a wire from the battery to the main fuse box or a wire from the starter relay bundle to the main fuse box.

May 16, 2018 | Ford Cars & Trucks

1 Answer

"Relearning" process for re-installation of blend door actuator motor (if necessary) on 1997 Ford F150.


There is no process, just make sure the battery negative cable is disconnected before install the part.

Apr 19, 2017 | Ford Cars & Trucks

1 Answer

Need to change the selenoid box in a 03 dodge caravan, just find out that i need to do the relearn procedure, HOW and is this true.


run the van up to 45mph then drop down to 25mph then back up to 55mph do this for about 5 time on the hwy and it should relearn what it needs to in the computer

Jan 28, 2014 | 2003 Dodge Caravan

1 Answer

Relearn tire position


You need a computer mechanic to hook up his computer and test the sensors. You may have a bad sensor in one of your tires

Jun 09, 2013 | GMC Sierra Cars & Trucks

1 Answer

It seems the battery in my 04 cadillac deville is dead. I know the battery is located under the rear seat. Can I remove it without adverse effects on the computer?


you can replace battery with out effects.first turn off radio.before removing negative battery cable.when you install new battery, when you start the engine let it idle until get operating temperature.the computer will have to relearn it memory while engine idling operating temperature.open throttle a little see if engine hesitate. it will hesitate some, when you can accelerate with out hesitation,engine tps sensor has relearned it position.if idle speed stable engine dont run rough and stall out in drive your pcm has relearned itself where you can drive it.

Apr 03, 2011 | 2004 Cadillac Deville

1 Answer

New ignition switch and key car would start


You need to relearn the ignition to the key,turn the key to on,and leave it on ten minutes,then turn it off,then right back on,do this three times,and thirty minutes.Let me know what happens.If this was at all helpful,please rate,thank you.

Jul 27, 2010 | 1999 Oldsmobile Cutlass

1 Answer

1991 voltage regulator problem dodge ram 250 van


The CPU is located under the hood on the firewall. It is the box looking item just left of center (as you look at it). I was having the same problem and was told to change the CPU. Now I need to findout how to relearn the CPU.

Jul 08, 2009 | 1985 Dodge Ramcharger

1 Answer

Hi i have a question


you need to get a used one out of a junkyard and just reconnect the wires. alldata also has a great site for wiring

Sep 10, 2008 | 1992 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...