Question about 2000 Chevrolet Blazer

1 Answer

How do you remove the starter from 2000 blazer

Having a problem getting the starter out of a 2000 chevy blazer 4 wheel driver

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Raise the front of vehicle & support on jackstands.It will help to take off the (left wheel on2.2L models,right wheel on 4.3L models)Remove skid plate(if equipped)On 2.2 models remove front driveshaft.On some early models,it may be necessary to raise the engine/transmission with a floorjack an under the transmission and remove the transmission crossmember for access to the starter motor bolts.On models so equipped ,remove the starter heat shield.From under the vehicle, disconnect the solenoid wire and battery cables from the terminals on the solenoid.Remove the starter mounting bolts, and then remove starter motor (note location of shims)

Posted on Jul 20, 2010

Testimonial: "This was quite the undertaking. I just couldn't figure why this starter wouldn't come out. Thank you very much for your time and knowledge. Dan"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starter on 2001 chevy blazer wont come by bframe


place the front of the car on jack stands than take off the front passenger side wheel and remove the starter from the inner wheel well

Oct 24, 2012 | 2001 Chevrolet Chevrolet Blazer

2 Answers

2000 blazer 4 wheel drive problem


It's most likely the "four wheel drive actuator" This is located on the front differential housing. It's cylindrical shaped and has a large hex (about
1-1/4") and two wires coming out of it. Usually they short out and blow the fuse but, I've also seen where they just quit working and sometimes they just get slow to work. The "actuator" has a heating element in it and it warms up, some sort gas, causing it to expand thus engaging the front wheels. In cold weather it may take a minute or so for it to engage, so put in four wheel drive and wait for a bit and see what happens.

Jan 05, 2010 | 2000 Chevrolet Blazer

1 Answer

4 wheel drive service light on the dash panel lit up on my 2000 chevy blazer, cannot push any buttons for 4 wheel drive to work, what could be the problem


most common problem is the TCSCM meaning transfer case shift control module,get back to me if you need more help PS this is not a cheap part

Dec 09, 2009 | 2000 Chevrolet Blazer

1 Answer

I have a 2000 chevy blazer with electronic 4 wheel drive. When I push the 4 wheel drive button it flashes but never goes into 4 wheel drive. Do have any suggestions


first thing is to check the 4wd acuator on the transfer case that goes bad all the time on those trucks, replace that il bet thats your problem,test it if its getting power then its bad . good luck.

Nov 13, 2009 | 2000 Chevrolet Blazer

3 Answers

How replace turn signal switch 2000 chevy blazer?


Since the 2000 chevy blazer is equipped with SRS (Saftey Restraint System), ie: Airbags, which is located in the steering wheel. In order to replace the turn signal switch you must remove the steering wheel. Therefore I would only highly advise you to take it to a dealer to have this done.

Oct 07, 2009 | 2000 Chevrolet Blazer

1 Answer

2000 Chevy Blazer stuck in 4L


try putting in neutral then try shifting in to 2h

Aug 17, 2009 | 1999 Chevrolet Blazer

1 Answer

Airbag removal 2000 Chevy Blazer 4.3l


there should be 2 or 4 bolts/screws on the back of the steering wheel

Jul 18, 2009 | 2000 Chevrolet Blazer

1 Answer

How do you remove the starter from a 1996 chevy 4WD blazer?


NO, it's kind of tight, but it's not that bad. You do need to remove the torque converter cover, and slide/rotate it as much to the driver's side of the vehicle as possible.

Jan 21, 2009 | 1996 Chevrolet Blazer

3 Answers

2000 Chevy Blazer


you have to remove motor mount bolts.... with engine hoist lift engine to get clearance to remove oil pan......you have to remove starter... trans cover ....... sounds like a easy job its not....hopethis helps

Dec 11, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

414 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...