Question about 2008 Toyota Sienna

Open Question

2008 Toyota Sienna rear brake caliper torque specification

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
morse008
  • 1111 Answers

SOURCE: reset piston on rear disc brakes 2008 Grand Caravan

they should screw in not compress

Posted on Aug 24, 2009

Testimonial: "Thanks--very helpful---fast response!"

Ad
  • 1 Answer

SOURCE: How do I replace the Rear Brake light bulb of 2001 Toyota Sienna?

I have a 2001 Sienna and have had to replace most of my tail light bulbs.

The bulbs that are mounted in the fender (wrap arounds) have acess panels in the van's interior that easily pop out and expose the back of the light assembly.

However, the bulbs that are found in the lift gate are a different matter. You have to remove the whole interior panel to the lift gate to expose the light assemblies. Go to your auto parts store and get a tool to help pop out the plastic retainers from the lift gates metal frame. Don't force the retainers out. Go slowly and gently so that you don't damage the interior panel. If you are really gentle you might even get to reuse the retainers.

Good luck!

Posted on Jul 01, 2009

  • 169 Answers

SOURCE: 06 malibu brake caliper torque specifications

caliper to knuckle 85' pounds----guide bolt for caliper slide 26' pounds English not metric pounds

Posted on Aug 30, 2009

johnjohn2
  • 5763 Answers

SOURCE: 2004 silverado rear brake torque specification,

31 ft lbs for caliper to bracket, then caliper bracket to nuckle is.148 ft lbs for 6400 & 7200 lbs GVWR or
122 ft lbs for 9900 lbs GVWR or
221 ft lbs for 12300 lbs GVWR.
good luck hope this helps.

Posted on Dec 21, 2009

Testimonial: "thanks for the quick response!!"

Molson02536
  • 3854 Answers

SOURCE: compressing the rear disc brake caliper on 2008 grand caravan

The rear calipers on these models require a special tool that compresses and turns the piston in at the same time -- most parts stores carry this tool.

It is called a caliper piston press -- and it installs where the pads would go and acts like a c-clamp,when turning handle it will turn the caliper piston backinto the caliper as it compresses it.
Anytime the brake rotor or brake pads are being replaced, the rear caliper piston must be seated (bottomed) to compensate for the new brake rotor or lining. Because the Parking Brake self-adjuster mechanism is attached to the piston, a special seating method is required. The only acceptable method is by rotating the piston back into the bore using Retractor,MILLER Special Tool 8807, . Any other seating method will damage the self-adjuster mechanism.
Good luck and hope this helps.

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Caliper and bracket bolts torque


alldata.com

or the FSM.
its all there.

Dec 26, 2013 | 2008 Toyota Highlander

1 Answer

How to change front disc brake rotors on 2005 toyota corolla


Replacing the rotors is usually a good idea if you experience shimmying when braking. It is recommend that you replace both the rotor and the brake pads at the same time. The reference for this information is from this site:

https://manicmechanics.wordpress.com/2017/10/25/how-to-change-brake-rotors-on-a-toyota-corolla/

1. Jack up the vehicle and put some jack stands under it.
2. Remove the Lug nuts and the tire.
3. Carefully remove the caliper and caliper bracket.
4. Remove the old rotor. And replace it with the new rotor.
5. Reassemble the caliper bracket
6. Put on the new brakes pads and reassemble the caliper.
7. Put the tire and lug nuts back on.
8. Be sure to use the proper torque specifications.
9. Remove the jack stands and lower the vehicle.
10. Read torque the lug nuts to the proper specification.
11. Follow the link for details and photos.

Brake Vibration How to Change Brake Rotors on Toyota Corolla

Oct 26, 2012 | 2005 Toyota Corolla

2 Answers

Brake esemble diagram


Hey Stan the man,need your vehicles info.,year,make,model and engine size and Tommy on the spot here will send you a picture diagram of your rear brake assembly.There's a special spring tool you can get at auto parts store to remove and install springs,me got one.

Oct 15, 2012 | Cars & Trucks

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

1 Answer

Change rear brake discs


  1. here is some instuctions on how to do the brake pad replacement this should help you out
  2. Jack up the vehicle on a secure metal part of the vehicle and place jack stands in the same area.
  3. 2 Lower the jack until the weight of the car is solely on the jack stands.
  4. 3 Loosen the lug nuts and remove the wheel from the vehicle, exposing the brake system.
  5. 4 Loosen the caliper slide pins from the rear of the caliper and slide the caliper pins out of the caliper.
  6. 5 Remove the caliper from the brake system and remove the old brake pads.
  7. 6 Secure the caliper to a part of the suspension with a bungee cord to avoid it hanging by the rubber brake hos, where it could be damaged or start leaking.
  8. 7 Loosen the two bolts that hold the caliper bracket to the vehicle and remove the caliper bracket.
  9. 8 Pull the rotor from the vehicle.
  10. 9 Measure the thickness of the rotor with the micrometer. Compare the measurement to the "minimum thickness" stamp on the rotor or the manufacturer specifications in the repair manual.
  11. 10 Take the rotors to a machine shop to have them resurfaced if they are above specification and need resurfacing. Verify the manufacturer's recommendations in the repair manual, as rotors do not always need to be resurfaced or replaced.
  12. 11 Reinstall the rotor on the vehicle.
  13. 12 Place the caliper bracket back on the vehicle and hand tighten the bolts on the back of it.
  14. 13 Torque the bracket bolts down to the manufacturer specifications in the repair manual.
  15. 14 Place a new hardware kit in the caliper bracket and set the pads in the hardware.
  16. 15 Press in the caliper piston with the caliper piston tool to allow the caliper to fit over the new brake pads.
  17. 16 Slide the caliper over the brake pads and reinstall the caliper slide pins.
  18. 17 Torque the caliper slide pins to the manufacturer's specifications.
  19. 18 Replace the wheel on the vehicle and torque it down to manufacturer specifications located in your repair manual.
  20. 19 Lift the vehicle off of the jack stand with the floor jack and remove the jack stands.
  21. 20 Lower the vehicle to the ground and remove the floor jack.
  22. 21 Press the brake pedal several times to pressurize the brake system before test driving the vehicle.
  23. 22 Drive the vehicle, performing several hard stops to make certain the brakes are operating properly.
jQuery('.article ol .image').each(function(i,e){ var $this = jQuery(this); $this.find('img').error(function(){ jQuery(this).remove(); $this.remove(); }); });

Aug 29, 2010 | 2001 Toyota Celica

1 Answer

Changing the rear disk brakes on a 06 toyota sienna, what is the process?


-Set up jack and properly block front tires.

-Do not set parking break as this may hender removing the rear calipers. Open hood and remove the brake resevoir cap.

-Remove hubcaps if applicable,

-Loosen Lugnuts but do not remove,

-Jack up van,

-Remove tire.

-Caliper should be visible. There are two bolts or hex heads on the back side that can be a pain to remove sometimes.

-Pull the caliper off the rotor, It is recomended to have the rotors turned or replaced. With the old pad still in place, take a c clamp or brake caliper squeezer and compress the caliper

-remove old pad, take note for the reinstall of the new pad.

-reverse the steps. This is a simple break down. Hope it helps

Feb 07, 2010 | 2006 Toyota Sienna

2 Answers

Are there any special tools needed to change the brakes on a 2006 toyota sienna? Standard two bolts that hold it on?


You will probably not need anything other than a metric socket wrench set.

Many Toyota models have disc brake calipers that will flip up or down when you remove one of the two bolts that hold the calipers on. I am not sure of the setup on the Sienna.

When you remove either the upper or lower bolt and move the caliper, you can then remove the old pads. Also, you will need to push the piston(s) back into their cylinders to give you enough space to install the new pads. A large C clamp will usually suffice to push in the pistons.

I assume that you are talking about the front (disc) brakes. Some autos still have drum brakes on the rear, and those are a different story. They require several specialty tools to remove and replace the shoes.

Oct 11, 2009 | 2006 Toyota Sienna

1 Answer

How to do front brake on 2008 toyota sienna


No special tools at all. Are you familiar with doing brakes? I wouldnt recommend it for a first timer, its not worth the lives of you and others. Ive also seen people take the wrong bolt out of calipers and spend triple what a brake job cost because they werent experienced and wanted to save a buck. A 17mm and pad spreader or big channel locks is all you need. Use Toyota pads and have the rotors cut..OR... Dont complain when they make noise all the darn time!

Jan 09, 2009 | 2008 Toyota Sienna

1 Answer

Brake rotors


Are there small retainer clips on the studs still? More than likely its just rust built up on the center hub. Take some sand paper to the center hub, as long as e-brake is released and caliper is off, it will come off. I'm not familar with the toyota sienna's but if they have internal drum e-brakes, I would back off the adjuster if they do.

Oct 05, 2008 | 2006 Toyota Sienna

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

707 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...