Question about Dodge Caravan

1 Answer

2001 Dodge Caravan 2.4 DOHC stalled, won't start. Can I pull the cam sensor on the right end of the valve cover to see if the cam is turning to see if the timing belt is intact? It has spark.

Posted by on

  • 1 more comment 
  • harmon41 Jul 19, 2010

    I will give it a try. I'll contact you if I need further assistance.
    thanks

  • harmon41 Jul 20, 2010

    To: 1kbron Subject: 2001 Dodge Caravan 2.4 DOHC

    As I suggested. I checked the fuel pump relay and fuse, checked the automatic shutdown relay and fuse. All worked. Next I disconnected the fuel line from the fuel rail. when the key was turned to the on position no fuel came from the fuel line, none. Is it likely that one of the fuel pumps is bad? If so, how do I determine wnich one?



    Steve H

  • harmon41 Jul 22, 2010

    To: 1 kbron Subject: 2001 Dodge Caravan 2.4 DOHC



    On that Dodge Caravan the fuel pump relay is working and the fuse is good. When the key is turned on the fuel pump buzzes only 1/3 to 1/2 second, no more. When the fuel loine is disconnected from the fuel rail ay the injectors there is no pressure and no gas comes out when the key is turned on. If the pump were working wouldn't gas shoot out of the fuel line?



    SteveH

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,796 Answers

Hi!!

Before you do that, check fuel pump relay, fuse and operation and pressure.
Make sure the injectors are energized and delivering gas when turning key on (they will do it for 2 secs. every time the key is open, have somebody turn the key while you check)
Open the PDC (fuse box) next to the battery, look for the Automatic Shutdown (ASD) Relay. It has a 20A fuse in it, make sure it is not blown.
If all of the above passes the tests, check camshaft and crankshaft Position sensors.

Keep me posted!! Good Luck!!

Posted on Jul 19, 2010

  • 1 more comment 
  • Rene J Solis Jul 20, 2010

    Hi!!



    The fuel pump relay and fuse are located in the engine compartment fuse box, if the fuse is OK, when you turn the key to the ON position, you should hear a click inside the relay amd a humming noise inside the fuel tank. Have somebody turning the Key while you check both thingsl, If relay clicks and no humming noise in fuel tank, REPLACE PUMP.



    Fuel Pump can be bought by itself or as an assembly, if you go for the fuel pump alone, also get the strainer with it. If gauges are working fine, go for the pump and strainer to save some $$$$$.



    Click on the link for a blow out of the pump assembly, in this site, you'll also find removal and installation instruccions. GOOD LUCK BUDDY!!!



    http://www.autozone.com/autozone/parts/2...

  • Rene J Solis Jul 20, 2010

    Oh!! Your vehicle only has ONE fuel pump!!!

  • Rene J Solis Jul 22, 2010

    If you have fuel in the tank, when you turn the key to on, you should have gas coming to the lines, if the lines are disconnected, place an clear empty small plastivc bottle of soda or something into the gas supply line, have someone turn the key to the ON position, you should see the bottle filling up for as long as the pump is on.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 dodge grand caravan sport 3 code 3.3 liter flex fuel random cylinder misfire along with 1 2 5 6 cylinder misfires. scan tools are unable to communicate with computer but check engine light will come...


Dirty fuel injectors. Computer will show misfire on the cylinders that are malfunctioning. If injector cleaner in tank won't clean them, pull them all out and have a professional take them apart and cleaned. Each injector has a screen in it that can get plugged up. Think about Bro, all other stuff has been renewed.

Jul 15, 2017 | 2001 Dodge Grand Caravan

3 Answers

Replace the PCV valve on the '09 dodge grand caravan


Hello! Here is the location of PCV valve for 3.3L, 3.8L, and 2.4L....Guru....saailer



saailer_87.gif

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Mar 08, 2011 | 2009 Dodge Grand Caravan

2 Answers

How do I replace the CAM sensor on a 1996 dodge neon?


Hi, my name is John I will do my best to assist you.

To Remove
  1. Disconnect the negative battery cable.
  2. Disconnect the filtered air tube from the throttle body and air cleaner housing.
  3. For SOHC engines, remove the air cleaner inlet tube.
  4. For SOHC engines, detach the electrical connectors from the engine coolant sensor and the camshaft position sensor.
  5. For DOHC engines, unplug the electrical connector from the camshaft position sensor.
  6. For SOHC engines, remove the brake booster hose and the electrical connectors form the holders on the end of the cylinder head cover.
  7. Unfasten the camshaft position sensor mounting screws, then remove the sensor.
  8. Loosen the screw/bolt attaching the target magnet to the rear of the camshaft.
To Install: NOTE: The target magnet has 2 locating dowels which fit into the machined locating holes in the end of the camshaft.

  1. Install the target magnet in the end of the camshaft. Tighten the retainer to 30 inch lbs. (3.4 Nm).
  2. Install the camshaft position sensor. Tighten the sensor mounting screws to 80 inch lbs. (9 Nm).
  3. For SOHC engines, place the brake booster hose and the electrical harness in the holders on the end of the valve cover.
  4. Attach the electrical connector(s) to the camshaft position sensor and coolant temperature sensor (if necessary).
  5. Install the air cleaner inlet tube and the filtered air tube.
  6. Connect the negative battery cable.
The camshaft position sensor is mounted to the rear of the cylinder head - SOHC engine shown


tecnovative_139.gif
Location of the camshaft position sensor - DOHC engine shown

tecnovative_140.gif

Unfasten the retaining bolt, then remove the target magnet from the rear of the camshaft - SOHC shown, DOHC similar

tecnovative_141.gif

The target magnet has 2 locating dowels for proper alignment during installation

tecnovative_142.gif

Feb 20, 2011 | 1996 Dodge Neon

1 Answer

2001 dodge caravan .. plugs 2 and 3 not giving spark changed cam sensor, wires, plugs, spark box, turns over but wont fire


try putting the original parts back on one at a time ,till it starts ,then have it diagnosed correctly by a diagnostic technician who will check the electrics over and find whats wrong

Dec 08, 2010 | 2001 Dodge Caravan

1 Answer

Were do i find the spark plugs on a 2001 doge caravan 2.4 liter


The 2001 Dodge Dual Overhead Cam engine spark plugs are located in the top center of the cylinder head--right between the cams. The ignition system uses a coil pack located right beside the plugs. The system has very short spark plug wires from the coil to the spark plug so current drop is very low over the length of the wire. The spark plugs are mounted at the base of a tube in the valve cover so an extension on a ratchet is required to reach them


Nov 24, 2010 | 2001 Dodge Caravan

1 Answer

In a 1993 the crank and cam sensors are in the timing cover on the Dodge Stealth dohc 3.0. But on the 92 it's at the end of the cam gear. How can I make this swap?


i would think you could take out the cam plug and put the sensor in but the cam if i remember right has a metal pin like a dowel inserted in a hole drilled in the camshaft and that is what the sensor reads. if there is no pin or other tab on the other engine then you would have to swap the cam

Mar 20, 2010 | 1993 Dodge Stealth

2 Answers

2001 FORD TAURUS 24 VALVE DOHC MOTOR WILL NOT START


i have a 2001 taurus 24valve dohc 3.0 engne i have a bad coil pack what steps do i need to do to change the coil pack

Sep 07, 2009 | 2001 Ford Taurus

1 Answer

If there is only starter turning mellow sound & all pistons,head,valves it is a sensor controling the spark is it the cam sensor,computor,coil pack same with head on or off 2.4 dohc 4cly


possible ignition control module or crank sensor find the module and get it tested does not cost anything at parts house to have done

Aug 31, 2009 | 1998 Dodge Caravan

1 Answer

2001 dodge grand caravan stalls


Check the sensors on the throttle body. There is a sensor that controls air to fuel ratio. If that sensor is bad then the car will run and then stall out while in drive. I had the same problem when it was cold outside last winter. If you dont want to dish out the money without knowing if it is that part at fault or not then start the van pop the hood and located the throttle body. Place your hand on the sensors and give them a little shake and then make sure they are plugged in all the way. You could also turn the van off and unhook the sensor clean the connectors and plug it back in. That should do the trick and if it doesnt stall anymore then I would replace those sensors if I was you. One more thing. If your giving the sensors a tug while the car is running and you hear it going to stall you could located the gas pedal cable and give it a rev or two by hand so it doesnt stall out and turn off. By the way. You van isnt over heating at all is it?

Feb 11, 2009 | 1994 Dodge Caravan

1 Answer

2001 dodge grand caravan stalls


Glad too hear your making progress, sounds like your dealing with a reasonable shop too. For future reference, take notes when your vehicle acts up. The more information you cn give your technician the easier it is to be fixed. Good luck, let me know how you make out.

R

Feb 10, 2009 | 2000 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...