Question about 2004 Isuzu Rodeo

Open Question

I have 2005 Holden Izuzu RA rodeo key remote reprogram

I have 2005 Holden Izuzu RA rodeo What to know how to have a remote reprogramed from another Vehicle to work on mine . Not just a resync. will not do it ! Is it possible via a TEC2 and if so how . Holden wont do it, just want to sell new remote $200 + charge to program to vehicle !

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
stevenhurc
  • 450 Answers

SOURCE: reprogramming remote and key

if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
Step Action
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.

Posted on Jun 21, 2009

Ad
stevenhurc
  • 450 Answers

SOURCE: torque settings for a holden rodeo 3.5 ra. Head

stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Posted on Dec 05, 2009

alicantecoli
  • 22306 Answers

SOURCE: is my holden rodeo 1999 ra v6 obd2 system

if it was sold in america yes ,if sold elsewhere no

Posted on Jan 19, 2010

  • 1 Answer

SOURCE: Intermitten loss of throttle car

you need to have the throttle body cleaned out or replaced

Posted on Apr 20, 2010

  • 383 Answers

SOURCE: holden rodeo brakelights dont work not even cab brake strip.

check your fuses

Posted on May 27, 2010

Testimonial: "i found problem fuses"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove fuel tank from ra diesel rodeo ?


I may be a little off on models,, but
it should have an in tank fuel pump that cam be removed from the top of the tank, should not have to remove tank on single cabs.
does the fuel pump run for a couple of seconds after you first turn the key on, could be an electrical fault, all wires/connections/fuses in sound condition?

Aug 03, 2014 | 2005 Holden Rodeo

1 Answer

2004 holden rodeo manual - how to reprogram new key


take the key and the car to a service dealer and have them program the two together.

Jan 22, 2014 | Cars & Trucks

1 Answer

Where to connect green tacho wire on holden rodeo ra 2005 model


The green wire is always a ground you must ground it

Sep 22, 2017 | Cars & Trucks

1 Answer

Where to connect green tacho wire on holden rodeo ra 2005 model


Assuming red is positive, black is negative or neutral the green is usually an earth wire and should be mounted to the cars frame.

Jul 08, 2013 | Cars & Trucks

1 Answer

Hi, can i program a new remote on my 05 RA rodeo without having to go to holden


If you have a working remote most locksmiths now supply and reprograme new remotes. Look them up in the phone book. If you have dont have a working remote you will have to go through holden.

Apr 19, 2011 | 2004 Isuzu Rodeo

1 Answer

Torque settings for a holden rodeo 3.5 ra. Head


stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Dec 03, 2009 | 2004 Isuzu Rodeo

1 Answer

I replaced the battery in the remote key but it does not work. Is there a way to reprogram the remote key? It is for a 1999 Isuzu Rodeo LS.


Hi usually to program the remote key is point to the dash and hold the activing button for a minute and a 1/2 and that should do the trik if not on the manual you have instrution on reprogramming the remote good luck

Aug 19, 2009 | Isuzu Rodeo Cars & Trucks

2 Answers

Reprogram remote key vx commocore


mr minit! locksmith! what area do you live in? most small workshops have a scan tool that will program commodore keys from vn to vy. hope this helps

Aug 04, 2009 | 2004 Isuzu Rodeo

1 Answer

Reprogramming remote and key


if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
Step Action
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.

Mar 26, 2009 | 2004 Isuzu Rodeo

Not finding what you are looking for?
2004 Isuzu Rodeo Logo

Related Topics:

483 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...