Question about 2000 Dodge Durango

1 Answer

Where i can take my car to put grease in

Where i can take my car to put grease in steering colum

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 200 Answers

A local garage or tire center

Posted on Jul 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Noise in stering colum only when i drive staight, if i turn wheel one way or other noise stops


if you are drive straight all the time than that part of is getting worn out. you mite see if the are any type of grease points on the steering
column, the grease in the center or as you stated driving straight it make alot of noise, the grease has broken down and now it is metal on metal or plastic on plastic. where as you turn right or left it picks up a little grease and soon you will start hearing the noise in any direction because the grease is braking down or drying out.

make sure there enough fluid in the steering control box, mite look for a condition fluid.

Apr 14, 2015 | Cars & Trucks

1 Answer

How put back together the steering wheel colume


get the FSM, factory service manual
or
alldata.com
login
read how to remove ignition switch, bingo.

Feb 24, 2015 | 1990 Jeep Cherokee Limited

1 Answer

Put in used steering colum and truck turns over but dosen't fire up


if you have a chip in the key the different key wont work with the ECM so youll have to have a dealer flash the ECM

Apr 16, 2013 | 1997 Ford Expedition

1 Answer

Low beam head lights are not working. High beams only work when you put the switch on then push the high beam arm on the steering wheel


you may have a problem with the dimmer switch for the headlights.its located on the top of the steering colume at the base of the colume near the firewall.

Aug 05, 2011 | 2003 Oldsmobile Bravada

1 Answer

Need to remove steering column on a 1992 lincoln town car


Remove the steering wheel, turn signal reset (plastic), remove clip and spring. Remove trim to expose the entire colum. Disconnect all connectors. There are four main bolts holding the colum up. Remove the bolts and lower the colum. At the end of the steering shaft there is a bolt going through the colum. Remove the bolt. The colum can then be removed.

Mar 04, 2011 | 1992 Lincoln Town Car

1 Answer

1991 buick regal, i need instructions on how to replace a ignition switch


key switch,remove center cap and pull steering wheel off with wheel puller.disconect horn,blinkers assembly.push pin remove ignition. ignition switch, remove panel under dash un bolt steering colum lower to seat un screw ignition from top steering colum un hook rod,un plug harnees put new one on put back together

Feb 02, 2010 | Buick Regal Cars & Trucks

1 Answer

Want to see diagram onputting steering colum of chevy astro van 1989 tried to put new ignition in wouldn't go. tookcolum apart and the bearings are bad. need to know how to put it back together.


come on this thing is so simple its untrue,why didnt you just cut the old lock off and put a new one on.As for the bearings just stick them back in with grease ,you should be able to get some at the bike shop ,but the bearing paths could be worn so if you can get a slighter bigger ball ?refitting is the reverse procedure to taking it apart

Oct 23, 2009 | 1989 Chevrolet Astro Cargo

1 Answer

I removed the tilt steering colum housing to instal a new cruise


The plastic piece goes between the steel rod and cruise/wiper lever. You will have to remove the wheel and the upper bearing housing to get it back where it goes. If you put some wheel bearing grease on it then it will stay in place during reassembly.. Good Luck

May 15, 2009 | 1986 Chevrolet El Camino

2 Answers

Hard to shift automatic transmission


check the shift cable for rust and make sure it is moving freely and if rusty spray some WD40 on it and then a light coating of grease

Feb 20, 2009 | 1992 Ford Aerostar Extended

1 Answer

Steering colum vacuum lines


they shoud both go to the vacuum switch on top of the column one is the vac source and the other goes to the release

Oct 15, 2008 | 1996 Lincoln Town Car

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

83036 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...