Question about 2005 Mercury Mariner

1 Answer

How to remove alternater 2005 mercury mariner 3.0 v-6

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Removal and Installation

  1. CAUTION: Do not allow any metal object to come in contact with the generator housing and internal diode cooling fins. A short circuit may result and burn out the diodes. Disconnect the battery.
  2. Remove the RH intermediate axle shaft.
  3. Remove the 6 lower splash shield bolts and the 2 pin-type retainers.
    • To install, tighten to 8 Nm (71 lb-in) .
  1. NOTE: The LH lower splash shield must be removed before the RH lower splash shield. Remove the lower splash shields.
how to remove alternater 2005 mercury mariner 3.0 - 118886165


  1. Remove the nut and position the bracket and wiring harness aside.
  2. Rotate the front end accessory drive tensioner counterclockwise and position the accessory drive belt aside.
  3. Position the generator B+ protective cover aside and remove the generator B+ terminal nut.
    • To install, tighten to 8 Nm (71 lb-in) .
  1. Disconnect the generator electrical connector.
  2. Remove the generator upper air duct bolt.
    • To install, tighten to 4 Nm (35 lb-in) .
  1. Loosen the 2 lower generator bolts and remove the generator upper air duct.
  2. Remove the pin-type retainer from the generator shield.
  3. Remove the bolt and the generator shield.
    • To install, tighten to 4 Nm (35 lb-in)
  1. Remove the generator stud nut.
    • To install, tighten to 47 Nm (35 lb-ft) .
  1. Remove the generator stud.
    • To install, tighten to 7 Nm (62 lb-in) .
  1. Remove the 2 generator bolts.
    • To install, tighten to 47 Nm (35 lb-ft) .
  1. Position the generator aside and remove the 3 generator lower air duct nuts.
    • To install, tighten to 4 Nm (35 lb-in) .
  1. Remove the generator lower air duct.
  2. Rotate the generator to gain enough clearance and remove it through the opening in the fender well.
  3. If necessary, remove the 2 generator bracket bolts and the generator bracket.
    • To install, tighten to 47 Nm (35 lb-ft) .
  1. To install, reverse the removal procedure.

Posted on Jul 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the OBD connector on a 2010 mercury mariner


Hi Chad,

Here is a follow up for you. The picture provided is from a 2005 with the OBD location. http://www.obd-2.de/carcode/pics/dlc/ford/Mercury-MarinerHybrid-2005.jpg .

Looking at many examples on line from all applications. The majority of these plugs are under the steering column. Either right or left mounted under the dash board.

On some foreign models . Remove the droor between the center console. And it will be mounted on the floor between the seats.

Fare . Well.

Dec 09, 2014 | 2010 Mercury Mariner

1 Answer

Whats causing my battery not to stay charged on my 2006 mercury mariner. I have already checked the alternater and its ok


As long as the alternator is putting out between 13.8v and 14.5 its OK. Load test the battery. The only other thing is a parasitic draw. Usually happens from a light staying on or some other keep alive memory device in the car. Easy way is to take a 12v test light and remove the positive battery terminal. Place the test light between the terminal and the battery with everything off. If the light comes on bright you have a draw. Leave the test light attached and try removing a fuse at a time until it goes out. Once it does you found the circuit to go after.

Aug 15, 2014 | 2006 Mercury Mariner

2 Answers

I want to change the amber side marker light on a 2005 Mercury Mariner but the manuel says to take it to a dealer to have it done. Is it that hard to do myself? Thanks


Side Lamp/Front Turn Signal Lamp Bulb

Removal and Installation
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.

  1. Remove the 2 fender splash shield bolts.
  1. Remove the 3 fender splash shield pin-type retainers.
  1. Remove the screw and position the fender splash shield aside.
  1. Remove the front turn lamp bulb holder from the lamp assembly.
    a0014324.jpg
  1. Remove the front turn lamp bulb.
  1. To install, reverse the removal procedure.

snorkelbobby_1.jpg

Dec 07, 2010 | 2005 Mercury Mariner

2 Answers

I would like to know if a 2005 mercury marier has a cabin filter


almost all cars built after 88 had cabin filters fitted,due to pressure from "the clean air" brigade.

Aug 24, 2010 | 2005 Mercury Mariner

1 Answer

Cd error


i would make sure theres no cd in and try taking the negative cable off for a few mins and then replacing it again.

Apr 05, 2010 | 2005 Mercury Mariner

1 Answer

Side Marker Bulbs


you need to remove entire assembly to access bulbs.it is secured by small hex head screws & a ''sliding tab'',an L shaped piece you pry up w/a flat screwdriver.

Jul 30, 2009 | 2005 Mercury Mariner

2 Answers

Cant find where the spark plugs are in my mercury mariner 2005


they will be on the opposite side of engine block

Jun 19, 2009 | 2005 Mercury Mariner

1 Answer

2005 mercury mariner charging probles


if the altinator is only charging 12.8 volts then its bad. it should be charging 13 to 14 volts

Mar 25, 2009 | 2005 Mercury Mariner

1 Answer

Replace alternator on 2005 mercury mariner


change alternator on a 2005 mercury mariner 2wd with a v6

Nov 16, 2008 | 2005 Mercury Mariner

Not finding what you are looking for?
2005 Mercury Mariner Logo

384 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

fordexpert

Level 3 Expert

5608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...