Question about 2001 Nissan Altima

Open Question

Service engine light on with code P1705

Service engine light on with code P170, Where is the accelerator pedal position sensor and how do you check it?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 2003 Nissan Altima 2.5S, Check Engine Light Problem.

this problem could be caused by the mass air flow censor, i had the same problem with my car. it is really pricey at the dealer so you might want to check elsewhere for this part. I found one at a scrap yard for 85% less that the dealer and i also got life time warranty, the dealer does not offer any warranty on this part.

Posted on Oct 22, 2008

Ad
localwonder
  • 6784 Answers

SOURCE: throttle Pedal Position Sensor Switch A

its just a sensor. you do not have to replace the entire throttle body.

Posted on Mar 16, 2009

  • 55 Answers

SOURCE: replacing bad camshaft position sensor

  1. Disconnect battery ground cable.
  2. Remove water pump pulley attaching bolts, then the serpentine belt and water pump pulley.
  3. Disconnect sensor wiring connector and remove sensor retaining bolt.
  4. Twist and pull sensor to remove.
Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring.

It is located under the water pump. Make sure when you remove the sensor that you rotate the crank shaft and look in the hole to make sure the pick up magnet is still in there. Sometimes they come loose and cause a no start or long crank. You will need to have the code cleared still.

Posted on May 06, 2009

  • 62 Answers

SOURCE: Accelerated and my service engine light came on

one of your vacuum hoses could have gottin disconected, go to autozone and have them pull the codes from the engine for free they will tell you.

Posted on May 10, 2009

FixurNissan
  • 61 Answers

SOURCE: check engine light on . engine speed sensor

The engine speed signal code is generated from the crank sensor. The crank sensor is located on the back side of the engine block. See image.

Thanks Jay!dd6b033.jpg

Posted on Jul 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 2010 Chevy impala. Reduced engine power. Service traction control and stability track. and check engine light. Codes are P2138 P2122 P0455


Electronic throttle control !
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit
DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage
DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit
DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

2009 Chevy Silverado P2138 Accelerator Pedal Position


Circuit/System Description
The throttle actuator control (TAC) system uses two accelerator pedal position (APP) sensors to monitor the accelerator pedal position. The APP sensors 1 and 2 are located within the pedal assembly. Each sensor has a 5-volt reference circuit, a low reference circuit, and a signal circuit.
Two processors are also used to monitor the TAC system data. Both processors are located within the engine control module (ECM). Each signal circuit provides both processors with a signal voltage proportional to pedal movement. The processors share and monitor data to verify that the indicated APP calculation is correct.

DTC P0455: Evaporative Emission (EVAP) System Large Leak

The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge solenoid valve OPEN and the EVAP vent solenoid valve CLOSED. This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge solenoid valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. The following table illustrates the relationship between the ON and OFF states, and the OPEN or CLOSED states of the EVAP canister purge and vent solenoid valves.

Nov 03, 2017 | Cars & Trucks

1 Answer

2006 impala 3.5 LT check engine and service traction control? Code: P2138


DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation
Electronic throttle control problem .
The throttle actuator control (TAC) system delivers improved throttle response and greater reliability and eliminates the need for mechanical cable. The TAC system performs the following functions:
• Accelerator pedal position sensing
• Throttle positioning to meet driver and engine demands
• Throttle position sensing
• Internal diagnostics
• Cruise control functions
• Manage TAC electrical power consumption
The TAC system includes the following components:
• The accelerator pedal position (APP) sensors
• The throttle body assembly
• The engine control module (ECM)

Accelerator Pedal Position (APP) Sensor
The accelerator pedal contains 2 individual accelerator pedal position (APP) sensors within the assembly. The APP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
The APP sensors are used to determine the pedal angle. The engine control module (ECM) provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors provide the ECM with signal voltage proportional to the pedal movement. The APP sensor 1 signal voltage at rest position is less than 1 volt and increases to more than 4 volts as the pedal is actuated. The APP sensor 2 signal voltage at rest position is less than 0.6 volt and increases to more than 2 volts as the pedal is actuated.
Search P2138 on youtube ,will show diagnostic steps .

Aug 19, 2017 | Cars & Trucks

1 Answer

Check engine light is on with code p1705


I doubt the fluid would cause the code. Depending on the year make and model, the code could be for a problem with the neutral safety switch, the throttle position sensor, or a clutch output sensor.
Four digit codes are brand and model specific.

Apr 22, 2013 | Cars & Trucks

2 Answers

2007 chevy tahoe loses power


No messaage of reduced engine power ? Your vehicle has electronic throttle control . Has four position sensors , two are located in the gas pedal ,an two in the throttle body . The PCM uses these sensor to know how much to open the throttle plate ,allowing more air into the engine . How did you read this code an where did you read it's definition at ? This is not a code for your vehicle . Some time cheap code readers get them wrong .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit
DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage
DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit
DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

DTC P1516: Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance
DTC P2101: Throttle Actuator Position Performance
DTC P2119: Throttle Closed Position Performance
DTC P2176: Minimum Throttle Position Not Learned

If one of this position sensors is bad it will throw the PCM into a
Reduced Engine Power Mode
When the ECM detects a condition with the TAC system, the ECM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
• Acceleration limiting--The ECM will continue to use the accelerator pedal for throttle control; however, the vehicle acceleration is limited.
• Limited throttle mode--The ECM will continue to use the accelerator pedal for throttle control; however, the maximum throttle opening is limited.
• Throttle default mode--The ECM will turn off the throttle actuator motor and the throttle will return to the spring loaded default position.
• Forced idle mode--The ECM will perform the following actions:
- Limit engine speed to idle by positioning the throttle position, or by controlling the fuel and spark if the throttle is turned off.
- Ignore the accelerator pedal input.
• Engine shutdown mode--The ECM will disable fuel and de-energize the throttle actuator.


017 Accelerator Pedal Position Sensors
Drive by Wire Function and diagnostics by Wells

Jan 01, 2018 | 2002 Oldsmobile Silhouette

2 Answers

Reduced engine power, service traction control, service stabilitrak


First of all a scan tool is need for this not a code reader, you need to view scan data after you find what code is stored in the PCM. It could have a problem with the powertrain control module, wiring, or the Accelerator Pedal Position (APP) Sensors. Here are a few codes that could set .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit

DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Oct 02, 2012 | 2008 Chevrolet Tahoe LS

3 Answers

Error code p2138


Here is the definition. You may need to have someone check the accelerator pedal position sensor and the circuit.

P2138 NISSAN Description The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the Engine Control Module (ECM).
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation
such as fuel cut.
Read more: http://engine-codes.com/p2138_nissan.html#ixzz26J3D2x8s

Sep 12, 2012 | 2010 Nissan Versa 1.8

2 Answers

Code p2138


P2138 is Throttle Pedal Position Sensor/ Switch D / E Voltage Correlation. Replace the Throttle Pedal Position Sensor/Switch.Remember to have the set code Cleared from the cars computer, this will turn off the check engine light and reset it. Good Luck and have a good XMASS.

Dec 17, 2010 | 2006 Nissan Altima

2 Answers

P 2138 code with service engine soon light on?


Accelerator Pedal Position Error.

P2138 - Accelerator Pedal Position Sensor Circuit Range / Performance Problem

Clear the code - if it recurs, change the sensor.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 15, 2010 | 2006 Nissan Altima

1 Answer

Error code 1680


Chevrolet OBD Fault Codes
DTC P1680 - Driver 5 (ECU malfunction)

This is any internal ECU problem (ECU = ECM = PCM device); check other details HERE; keep in mind that its possible that you have to reprogramm the ECU.

Here is a bulletin for this problem.Subject: Service Engine Soon Light On, P1680 (Reprogram or Replace PCM)

Models:
2004 Buick Rainier
2004 Chevrolet Trailblazer
2004 GMC Envoy
2004 Oldsmobile Bravada with 4.2L Engine (VIN S - RPO LL8)

Some customers may comment on the Service Engine Soon Light coming on. Upon investigation, the technician may find a P1680 diagnostic trouble code Check the resistance of the accelerator pedal position sensors using the procedure in the appropriate Service Information for DTC P1680.

If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built prior to the following VIN breakpoints, then reprogram the PCM with the latest calibration.

If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built after the following VIN breakpoints, then replace the PCM. If the resistance of the accelerator pedal position sensor is outside the specifications shown in the Service Information, then continue with the diagnostics for DTC P1680.

VIN Breakpoints
• Vehicles built at Oklahoma City Assembly Plant - 46192755
• Vehicles built at Moraine Assembly Plant - 42315833

Hope this help

Aug 03, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

I have problem with code 1126 (toyota 4 runner 2001


Manufacturer Specific Codes

P1100
BARO Sensor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1120 Accelerator Pedal Position Sensor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1121 Accelerator Pedal Position Sensor Range/Performance Problem

P1125 Throttle Control Motor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1126 Magnetic Clutch Circuit

P1127 ETCS Actuator Power Source Circuit

P1128 Throttle Control Motor Lock

P1129 Electric Throttle Control System

P1130 Air/Fuel Sensor Circuit Range/Performance (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code - More Related Information

P1133 Air/Fuel Sensor Circuit Response (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code

P1135 Air/Fuel Sensor Heater Circuit Response (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code - More Related Information

P1150 Air/Fuel Sensor Circuit Range/Performance (Bank 1 Sensor 2)

P1153 Air/Fuel Sensor Circuit Response (Bank 1 Sensor 2) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code

P1155 Air/Fuel Sensor Heater Circuit. (Bank 1 Sensor 2)

P1200 Fuel Pump Relay Circuit

P1300 Igniter Circuit Malfunction - No. 1

P1305 Igniter Circuit Malfunction - No. 2

P1335 No Crankshaft Position Sensor Signal - Engine Running

P1349 VVT System

P1400 Sub-Throttle Position Sensor

P1401 Sub-Throttle Position Sensor Range/Performance Problem

P1405 Turbo Pressure Sensor Circuit

P1406 Turbo Pressure Sensor Range/Performance Problem

P1410 EGR Valve Position Sensor Circuit Malfunction - Read Our Article on EGR Valve Codes For Help With This Toyota Check Engine Light Code

P1411 EGR Valve Position Sensor Circuit Range/Performance - Read Our Article on EGR Valve Codes For Help With This Toyota Check Engine Light Code

P1500 Starter Signal Circuit

P1510 Boost Pressure Control Circuit

P1511 Boost Pressure Low

P1512 Boost Pressure High

P1520 Stop Lamp Switch Signal Malfunction

P1565 Cruise Control Main Switch Circuit

P1600 ECM BATT Malfunction

P1605 Knock Control CPU

P1630 Traction Control System

P1633 ECM

P1652 Idle Air Control Valve Control Circuit

P1656 OCV Circuit

P1658 Wastegate Valve Control Circuit

P1661 EGR Circuit

P1662 EGR Bypass Valve Control Circuit

P1700 Vehicle Speed Sensor '2' Circuit Fault

P1705 Direct Clutch Speed Circuit Fault

P1765 Linear Shift Solenoid Circuit Fault

P1780 Park/Neutral Position Switch Malfunction (Only For A/T)

Back To Top Of Toyota Check Engine Light Codes Page

Mar 21, 2009 | 2002 Toyota 4Runner

Not finding what you are looking for?
2001 Nissan Altima Logo

Related Topics:

371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...