Question about 1992 Chrysler Lebaron

1 Answer

Lost the keys and don't have an extra set, is there any way to get a new set of keys without changing all the locks and ignition?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 977 Answers

You might have to get a locksmith to do it for you, that might be the cheapest way to do it .....hope this helps....cheers

Posted on Jul 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 chevy cavilier ignition replacement


You cannot its that simple you need to chenge the whole steering lock you cannot change the barrel without the original key

Dec 17, 2013 | 1997 Chevrolet Cavalier

1 Answer

Lost key and alarm dodge caravan


to reprogram new key first you need to use 2 factory program keys.place first factory key in the ignition first turn ignition on for 3 seconds. then turn off ignition then install second factory in the ignition on position for 10 seconds.when immobilizer warning lamp begins to flash a acoustic signal is emitted.within 60 seconds. switch ignition off and remove key.then insert new key and switch on for 10 seconds a acoustic signal is emitted and immobilizer warning lamp remain illuminated for 3 seconds indicating programming completed.if all fails dealership has to reprogram new keys.

Dec 17, 2012 | 2000 Dodge Caravan

1 Answer

How to take ignition switch out without key?


It can be done but you will need to drill out the locking tab that holds the lock cylinder into the housing. This is not an easy process and you could mess up the steering column if you don't do it correctly. Your best bet is to call a lock smith or bring proof of ownership to your local dodge dealer and have them make you a key.

Aug 25, 2012 | Cars & Trucks

1 Answer

How to remove the ignition lock on a 1994 Surburban without a key


A key code is stamped on the lock cylinder to aid in replacing lost keys.

Aug 06, 2012 | 1994 GMC Suburban

2 Answers

Lost my keys,now i have to change my ignition switch, how do i go about doing this? its on a 89 chevy extra cab truck


You need to remove the steering wheel. Then remove the lock plate. Then unbolt the turn signal switch and move it out of the way. Remove the connector for the key dinger to access the bolt that holds the lock cylinder in.

Apr 06, 2010 | 1989 Chevrolet K1500

4 Answers

How to program the orginal remote camry key2003


I found this on the internet try it it MAY work.

Start with the key out of the ignition. Open the driver door (all other doors are closed). Driver door is unlocked (other doors don’t matter).


Perform these steps within 5 seconds
Insert the key into the ignition (don’t turn it)
Insert the key into the ignition (don’t turn it)


Perform these steps within 40 seconds
Close, then open the drivers door.
Close, then open the drivers door.
Insert the key into the ignition (don’t turn it) and pull it out.


Perform these steps within 40 seconds
Close, then open the drivers door.
Close, then open the drivers door.
Insert the key into the ignition and leave in the ignition.
Close the drivers door
Turn the ignition to ON (as far as you can go without cranking the engine), then back to off .
Remove the key from the ignition.


Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.


Perform these steps within 40 seconds
Press the lock and unlock buttons on the transmitter simultaneously for 1.5 seconds
Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.


Open drivers door

Dec 18, 2009 | 2003 Toyota Camry

4 Answers

My dad lost my keys and i need a new ignition key.


cheapest way is to remove strinng column panel and replace the igntion lock cylider $15 it does take a little effort to get it out also a locksmith may be able to cut you a new key by hand for $100

Aug 25, 2009 | 1992 Ford Ranger

1 Answer

Lost working keys extra will unlock but does not start how do i program extra key to start car


On 2002 model try the following:
1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).

6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.


from ProgramyourRemote

Jul 04, 2009 | 2002 Chevrolet Tahoe

1 Answer

Changing ignition key switch


Well,

From what I remember you need to put the missing key in and then press the cylinder release, a small hole by the ignition switch. Without the key, I guess you would need a locksmith to turn the tumbler then press the switch. Lock pick set anyone?

Jul 18, 2008 | 1986 Chevrolet Caprice

Not finding what you are looking for?
1992 Chrysler Lebaron Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...