Question about Cars & Trucks

Open Question

Lexus es330 rear brake caliper adjustment is there a way

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: cant compress piston on rear brake calipers

Use a caliper wind back tool which rotates the piston at the same time as pushing it back. Release the bleed screw to assist the wind back. If you use a brake hose clamp on the brake hose this will reduce the need to bleed the system.

Posted on Apr 13, 2009

Ad
  • 2 Answers

SOURCE: how to adjust caliper for rear brakes on a Mazda Protege Es.

yep, this is what u do. i read that this controls hand break and you need to completely loosen that using hex (3mm) key. BUT, when u tighten it back up, u need to unscrew it about 1/8th, VERY important, or ur pads will be rubbing way too much against the rotor. I actually had to do about 1/2 the turn to make the wheel spin w/out too much pressure.

Posted on May 03, 2009

  • 677 Answers

SOURCE: sticking rear brake caliper 2002 mondeo 1.8

Is the piston sticking in the caliper or is the caliper sticking on the outside slides preventing it from moving to the disc?

Posted on Aug 31, 2009

roniecon
  • 6927 Answers

SOURCE: 2006 Kia Spectra 5 rear brake disc replacement

One side,turns right,and push in slightly,and the other side turns left,to retract.

Posted on Apr 20, 2010

  • 972 Answers

SOURCE: 2006 Kia Spectra 5 rear brake disc replacement

you need a special tool avalable at most parts stores. its a disc brake piston turning tool. you have to rotate piston clockwise while pushing in on piston. you can fabricate something that enguages the slots and push and turn till all the way in.make sure to note position of slots and put them in same place as was before or the pin on the pads wont enguage the slot

Posted on May 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 Lexus 460L and have issues with the brakes grabbing randomly - it is so bad that if not wearing a seat belt a person could hit the windshield even at low speeds...Lexus of course has no...


Hi Deanna, have someone look for rusting or other contamination on the brake pistons of the calipers. If all is good there try replacing the brake discs. (I believe that in the States they are called rotors) Ask for the tightness and fitting of the calipers to be inspected and checked and that the self adjusting mechanism is free and sliding correctly. Regards John

Oct 24, 2012 | Lexus Cars & Trucks

1 Answer

1998 Lexus GS300: The dashboard warning light for the tail lights is on


I had this with my ES330. It turned out to be the upper brake light in the rear window. Despite my wife and I checking all the lights multiple times, a friend pointed out the obvious. A new bulb fixed it.

Jan 11, 2012 | 1998 Lexus Gs 300

1 Answer

How do you adjust the parking brake on the 1997 sable


they r a self adjusting cable....if ur sable has rear drum brakes then adjust the rear shoes...if it has rear disc brakes then u have a faulty rear brake caliper..the parking brake system is also inside the rear brake calipers

Jul 16, 2011 | 1997 Mercury Sable

1 Answer

Leaking brake fluid at rear passenger '92


Hi,
Most likely a brake caliper or line. Lines are fairly cheap, calipers cost about $75 a piece if you get them discount online. Novice mechanics can do either or both replacements. DOnt buy parts from a dealer, they are 40% higher than retail. A brake shop will run you in the range of $150 to replace the caliper and pads one one axle, about $300 on both rear (replace both is recommended). Mike

Jun 14, 2011 | 1992 Lexus Ls 400

1 Answer

2004 lexus es330 car shakes when brakes are applied


brakes shaking means the rotors are warped.

replace the brake rotors.


REMEMBER TO RATE THIS ANSWER

THANK YOU

Dec 26, 2010 | Lexus ES 330 Cars & Trucks

1 Answer

How to remove rear rotor after wheel is off


Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552).
1.Remove the brake caliper bolts (2W303).
2.Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220aca3301.gif
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract(push back to allow clearance) the parking brake shoe and lining.
  2. Remove the rear brake disc.

Feb 11, 2010 | 1998 Mercury Mountaineer

1 Answer

How to change rear brake pads on 06 Lexus GS 300


Rear brakes similar to fronts except that caliper piston must be screwed back instead of compressed (due to use of parking brake).

Jul 10, 2009 | 2006 Lexus Gs 300

1 Answer

Adjusting rear brakes


there is no adjustment when you pump pedal the pressure comes automatic.the only adjustment is e-brake.

Apr 26, 2009 | Lexus RX 300 Cars & Trucks

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...