Question about 1995 Honda Accord

1 Answer

How do you set the timming on a 95 honda accord

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 6,826 Answers

1990–95 4-Cylinder Accord and 1992–95 Prelude

  1. .
  2. Fig. 10: On all engines except VTEC, the belt adjuster arm must be locked in place using one of the lower cover mounting bolts how do you set the timming on a 95 honda accord - 86803136.gif
    NOTE: There are two belts in this system; the one running to the camshaft pulley is the timing belt. The other, shorter one drives the balance shaft and is referred to as the balancer belt or timing balancer belt. Use a piece of chalk or a marker to place an identifying arrow on the belts. The arrow can identify the direction of rotation or the outer edge of the belts. The belts must be reinstalled so it moves in the same direction. Protect the belts from oil, coolant, etc. It's an even better idea to replace the belts at this point.
  3. Loosen the timing belt adjustment nut. Push on the tensioner to relieve tension from the balancer belt, then tighten the nut. Remove the balancer belt.
  4. On all models except Prelude with VTEC, loosen the lockbolt installed earlier and the adjusting nut. Push on the tensioner to release the timing belt, then tighten the nut. Carefully remove the timing belt. On Prelude VTEC models, remove the timing belt from the pulleys, then remove the bolts securing the auto-tensioner. Remove the auto-tensioner from the engine. To install:
  5. Check the position of the timing marks. The timing pointer must be perfectly aligned with the TDC (white mark) on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head. Additionally, the face of the front timing balancer pulley has a mark which must be aligned with the notch on the oil pump body. This pulley is the one to the left crank when viewed from the pulley end.
  6. Fit the timing belt over the pulleys and tensioner. On DOHC engines without VTEC, remove the 5mm pin punches from behind the cam pulleys.
  7. Except Prelude VTEC models:
    1. Temporarily install the crank pulley and bolt.
    2. Loosen the tensioner adjusting nut 1 turn, then tighten it. Rotate the crankshaft counterclockwise until the camshaft pulley has moved 3 teeth to create tension on the belt. Loosen the nut again, then tighten it to 33 ft. lbs. (45 Nm). NOTE: Always rotate the crankshaft counterclockwise when viewed from the pulley end. Rotating it clockwise will cause improper adjustment and possible damage.
    3. Tighten the lockbolt installed earlier to lock the timing belt adjuster arm. Remove the crank pulley.
  8. On Prelude VTEC models:
    1. Hold the auto-tensioner with the maintenance bolt facing up. Loosen and remove the bolt. NOTE: Handle the tensioner carefully so the oil inside does not spill or leak. Replenish with clean engine oil if any does leak. Total capacity is 1⁄4 fl. oz. (8 ml).
    2. Clamp the mounting flange of the tensioner in a vise using a cloth or blocks of wood to protect it. Insert a flat blade screwdriver into the maintenance hole. Place the stopper (tool number 14540-P13-003) or an equivalent clamp on the tensioner, then turn the screwdriver clockwise to compress the bottom. Be careful not to damage the threads or the gasket contact surface.
    3. Install the maintenance bolt on the tensioner with a new gasket. Tighten to 6 ft. lbs. (8 Nm).
    4. Make sure no oil is leaking from around the maintenance bolt, then install the tensioner on the engine. Make sure the stopper stays in place and tighten the bolts to 16 ft. lbs. (22 Nm).
    5. Remove the stopper. Fig. 11: On VTEC engines, the tensioner must be compressed before installing it on the engine 86803137.gif
      Fig. 12: Remove the stopper after installing the tensioner on the engine 86803138.gif

  9. Make sure all timing marks are positioned correctly (as described earlier).
  10. Align the rear timing balancer pulley (to the right of the crank pulley) using a 6x100mm bolt or rod. Mark the bolt or rod at a point 2.913 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the rod into the hole. Align the 74mm mark with the face of the hole. This pin will hold the shaft in place during installation.
  11. Loosen the tensioner adjusting nut and verify that the timing balancer belt adjuster moves freely. Fig. 13: The balancer shaft must be held in position during timing belt instalhow do you set the timming on a 95 honda accord - 86803139.gifrel='nofollow' href="http://arrc.epnet.com/autoapp/8680/chiltonimages/8680/86803139L.gif">86803139.gif

  12. Fit the balancer belt over the pulleys. Remove the bolt or rod from the maintenance hole.
  13. Temporarily install the crank pulley. Rotate the engine one turn counterclockwise, then tighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm). Double check the positions of the timing marks and make sure they still line up. If not remove the belts and repeat the procedures. NOTE: Both belt adjusters are spring-loaded to properly tension the belts. Do not apply any additional pressure to the pulleys or tensioners while performing the adjustment.
  14. Remove the crank pulley. Remove the lockbolt installed earlier on the timing belt adjuster arm. Install the maintenance bolt with a new washer. Tighten it to 22 ft. lbs. (30 Nm).
  15. Install the lower cover, making certain the rubber seals are in place and correctly located. Tighten the retaining bolts to 9 ft. lbs. (12 Nm).
  16. If applicable, raise the lower beam and engine into place. Install the rear bolts for the lower beam. Tighten them to 28 ft. lbs. (39 Nm) on 1990–91 Accords, 37 ft. lbs. (50 Nm) on 1992–95 Accords and 43 ft. lbs. (60 Nm) on 1992–95 Preludes.
  17. Install the key on the crankshaft and install the crankshaft pulley. Apply oil to the bolt threads and tighten it to the following:
    • 1990 Accord: 166 ft. lbs. (230 Nm)
    • 1991–93 Accord: 159 ft. lbs. (220 Nm)
    • 1992–93 Prelude: 159 ft. lbs. (220 Nm)
    • 1994–95 Accord and Prelude: 181 ft. lbs. (245 Nm)
  18. Install the dipstick tube and dipstick.
  19. Install the side engine mount (refer to engine removal and installation for procedures). Remove the jack from under the engine.
  20. Install the upper belt cover.
  21. Install the side engine mount support bracket if it was removed.
  22. Install the valve cover.
  23. Install the compressor and/or alternator drive belt; adjust the tension.
  24. Route the wiring harness over the valve cover and connect the wiring to the alternator.
  25. Install the power steering pump and install the belt.
  26. Reinstall the cruise control actuator. Connect the vacuum hose and the electrical connector.
  27. Double check all installation items, paying particular attention to loose hoses or hanging wires, untightened nuts, poor routing of hoses and wires (too tight or rubbing) and tools left in the engine area.
  28. Refill the engine coolant.
  29. Install the splash shield under the engine.
  30. Connect the negative battery cable.
  31. Start the engine, allowing it to idle. Check for any signs of leakage or any sound of the belts rubbing or binding.

Posted on Jul 21, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Slipped timing belt on a 2008 honda accord, should i have it repaired or the engine replaced?


Hi ,1st I would make sure the timing marks are lined up,if they are your most likely fine,if not get a new timming chain,line up the cam and crank timmind marks install the chain and start it ,if the m,arks stay lined up and runs ok your set.I'ts cheap and easy to do for just the price of a timming chain.See ya,Don

Mar 01, 2013 | 2008 Honda Accord

1 Answer

Japanese honda 1998 hinda inspire timming


autozone should be able to provide this printout..

Jan 25, 2013 | 1989 Honda Accord 4 Door

1 Answer

95 acord v6 wont go over 3800 rpm cuts out code o336 crank senser a i replaced still same


did you replace the whole distributor,could be the ignitor also.










TIM........

Oct 23, 2010 | 1995 Honda Accord

1 Answer

How to change a brake light switchon a 95 honda accord


The switch is located on the foot brake lever. there is a pin to pop off, then pull the switch off and disconnect the plug fairly easy to do

Jun 15, 2010 | 1995 Honda Accord

2 Answers

Timming belt broke on 92 accord,set cranke to tdc


you will need to open the engine up if you can not turn the cam fully. something has been bent or broken or else it will turn. by breaking your timing belt was it shredded? if so you do have internal damage

Feb 11, 2010 | 1992 Honda Accord

1 Answer

Set timing


v teck or single, single cam says up on it crank has 2 b on combustion duall cams r facuing each other crank d same
easy call me 559 5796874 california

May 25, 2009 | 1995 Honda Accord

1 Answer

95 honda accord


I believe there's either a set screw or a release pin in back of the rest post(s) and then you can completely remove after that

Oct 25, 2008 | 1995 Honda Accord

1 Answer

Are the water pumps interchangeable?


best way to find out... is to phone autozone or a specialty store and have them look up the part numbers for each. even better is to call your local junk/recycling/wrecking yard as i believe they would have a set of books listing interchangable parts on different models... the coil pack on my windstar van is the same they use in the toyota model.

Robert

Sep 21, 2008 | 1995 Honda Accord

Not finding what you are looking for?
1995 Honda Accord Logo

962 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...