Question about 2003 Chrysler PT Cruiser

1 Answer

I am trying to replace the fan in my 2003 PT Cruiser. I have taken the hoses off and drained the anti-freeze,but I can find the way to get the fan and housing out.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It goes out the bottom. Jack up car, use stands, From the top, rotate the housing down on the left side about 90 degrees. Housing will drop out.

Posted on Jul 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can i top radiator up with water on pt cruiser 2001


If you live in a warm weather climate that does not get below freezing temps than temporarily topping off with water until a repair is made is fine. Anti-freeze has other properties besides keeping the coolant from freezing. It also helps keep the engine cool by more efficiently transferring heat out of the engine. It also has anti-corrosion additives that keep metal parts from corroding.

So although it may seem that anti-freeze has only one purpose it actually has several.

Dec 16, 2010 | 2002 Chrysler PT Cruiser

1 Answer

Replacing thermostat in 03 pt cruiser would like a diagram of where to find and how to replace


remove upper intake manifold, drain coolant partially, remove upper radiator hose from outlet connector, removeouter connector bolts, remove thermostat assembly, and clean the surface

Jun 18, 2010 | 2003 Chrysler PT Cruiser

1 Answer

Ongoing P0441 purge code on 2003 PT Cruiser GT. I


if you have replace the purge solenoid the problem is either the vaccum supply hose is loosing vaccum or the purge side is hose is either blocked or cracked.

Apr 21, 2010 | 2003 Chrysler PT Cruiser

1 Answer

How do i remove radiator fan from my 2004 pt cruiser?


Hope this helps!

Removal & Installation
NOTE The fan motor, fan, and the shroud are serviced as an assembly.



CAUTION Do not open the radiator draincock with the system hot and under pressure, because serious burns from coolant can occur.


  1. Disconnect negative cable from battery.
  2. Remove battery and battery tray.
  3. Drain cooling system below upper radiator hose level.
  4. Remove grille.
  5. Remove upper radiator closure panel and center brace.
  6. Disconnect upper radiator hose from radiator.
  7. For turbocharger equipped vehicles: Remove radiator inlet neck.
  8. Hoist vehicle.
  9. Disconnect radiator fan electrical connector (.
  10. Remove the two lower and left side radiator fan screws and.
  11. Lower vehicle and remove the remaining radiator fan attaching screws.

    WARNING Care should be taken not to damage the radiator cooling fins and tubes during fan removal.

  12. Remove radiator fan by lifting up from the engine compartment.

c83d6ac.gif
Radiator fan mounting points

To install:
  1. Install the radiator fan into position on the radiator.
  2. Hand-start all radiator fan fasteners.
  3. Tighten all radiator fan retaining screws to 55 inch lbs. (6 Nm).
  4. Connect the radiator fan electrical connector.
  5. Carefully lower the vehicle.
  6. For turbocharger equipped vehicles: Inspect radiator inlet neck O-ring. Replace if necessary. Install radiator inlet neck. Torque fasteners to 55 inch lbs. (6 Nm).
  7. Connect the upper radiator hose to radiator. Align hose and position clamp so it will not interfere with the engine or the hood.
  8. Install upper radiator closure panel and center brace.
  9. Install grille.
  10. Install battery tray and battery.
  11. Connect cables to battery.
  12. Fill cooling system.

Apr 18, 2010 | 2004 Chrysler PT Cruiser

1 Answer

Overheating


water pump ,its a plastic impeller and its loose on the shaft ,,,,,had one a while ago exactly the same but the first time i came across this on a saab i done the same as you ,changed everything ,felt a right you know what

Sep 01, 2009 | 2002 Chrysler PT Cruiser

1 Answer

2005 PT Cruiser leak anti-freeze leak????


the overflow bottle probobly has a crack in the seam of the bottle.you can replace the bottle or remove it and use some epoxy to repair it.

Jul 29, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
2003 Chrysler PT Cruiser Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...