Question about 1996 Chrysler Cirrus

1 Answer

Changing fuel pump. Have tank down. Cannot remove retaining ring.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 109 Answers

Regardless of engine,2.4L, 2.5L, they use the same pump module setup, the retaining ring is a white collar that is threaded on, use flat but blute chissel, flat file, to knock againts the lugs that are around the outside of the ring, or use very large water pump pliers and turn couterclockwise, make sure area is clean, or if you have access to a very large pulley puller, that will work to, even a plumbing gater strap will work to. GOOD LUCK. RDJRP

Posted on Jul 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96tahoe4 door fuel pump removal. the retaining ring is sealed like its spot welded from the factory I'm questioning if the fuel pump has ever been change before.ODOMETER reading is 267000 miles.


The ring that retains the pump in the tank needs to be rotated counterclockwise about 15 - 20 degrees so it will come free. If you are chiseling off any tabs, you may wind up having to replace the entire tank. The tabs locate and lock the retaining ring. See the attached YouTube vehicle.
How to Install Fuel Pump E3932M 1996 1997 Chevy Tahoe and GMC Yukon E3932M

Feb 14, 2017 | 1996 Chevrolet Tahoe

1 Answer

How do i replace fuel pump 95 taurus 3.0 6v ohc


You must remove the fuel tank to replace the fuel pump.
  1. Remove fuel tank.
  2. Remove any dirt that has accumulated around fuel pump module retaining flange.
  3. Turn fuel pump module locking retainer ring (#1)counterclockwise using Fuel Tank Sender Wrench 310-D006 and remove fuel pump module locking retainer ring.
  4. Pull fuel pump module sender plate up out of fuel tank until locking tabs(#3) for fuel pump module are accessible. Reach through fuel pump module opening, squeeze both locking tabs together and remove fuel pump module from fuel tank.

26441642-y320zuz4l2sbnhw34kuglarm-4-0.gif

Jan 10, 2017 | Cars & Trucks

2 Answers

Where is fuel pump for 1996 mercury mystique located on the car and how do you remove it


SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B
Removal
  1. Depressurize fuel system as outlined in Service Procedures- Fuel System Pressure Relief.
  1. Remove rear seat cushion. Refer to Section 01-10.
  1. Remove plastic grommet from floor pan.
  1. Disconnect fuel pump module electrical connector.
  1. NOTE: To disconnect fuel tubes from fuel pump module, compress tabs on both sides of each nylon push connect fitting and ease fuel tube out of fuel pump module.

    Disconnect fuel and vapor return tubes from fuel pump module.
  1. Turn fuel pump locking retainer ring counterclockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent and remove fuel pump locking retainer ring.
  1. NOTE: After fuel pump module removal, immediately cover fuel pump module opening in fuel tank in order to prevent fuel system contamination.

    Remove fuel pump module and cover fuel pump module opening in fuel tank.
  1. Remove fuel pump module O-ring seal and discard.
Installation
  1. NOTE: When cleaning fuel pump module mounting surface on fuel tank, use caution to prevent any foreign material from entering fuel system.

    Clean fuel pump module mounting flange and fuel pump module mounting surface and O-ring seal groove on fuel tank.
  1. Apply a light coat of Premium Long-Life Grease XG-1-C, -K or equivalent meeting Ford specification ESA-M1C75-B on a new O-ring seal to hold it in place and install it into the O-ring seal groove on the fuel tank.
  1. Install fuel pump module carefully to ensure that filter is not damaged. Make sure that locating keys are in keyways and O-ring seal remains in place.
  1. Hold fuel pump module in place and install fuel pump locking retainer ring finger-tight. Make sure that all locking tabs are under fuel tank lock ring tabs.
  1. Secure fuel pump locking retainer ring by rotating clockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent until fuel pump locking retainer ring rests against stops.
  1. Connect fuel and vapor return tubes to fuel pump module.
  1. Connect fuel pump module electrical connector.
  1. Install plastic grommet in floor pan.
  1. Install rear seat cushion. Refer to Section 01-10.
  1. Install Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B as outlined in Service Procedures-Fuel System Pressure Relief.
  1. Turn ignition switch to RUN position for three seconds repeatedly (5 to 10 times) until pressure gauge reads at least 270 kPa (30 psi). Check for leaks at fittings.
  1. Remove pressure gauge, start engine and recheck for leaks.
Hope this helps

Aug 13, 2011 | 1996 Mercury Mystique

1 Answer

2005 toyota corolla. no problems yesterday..this morning it was dead. I can jump it and it turns over but it won't stay running. doesn't seem to be getting any fuel. Which fuse could be causing this...


Fuel Pump-(test for current at the fuel pump using a multimeter or test light while cranking) Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Relieve fuel system pressure.
  3. Disconnect the battery ground cable.
  4. Remove the rear seat cushion.
  5. Remove the rear floor service cover mounting screws and remove the cover (except '02-'04). toy_car_cor-02-04fuelpump2.gif

  6. Remove the butyl tape and remove the floor service cover ('02-'04).
  7. Remove the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Remove the fuel line U-clip and remove the fuel line from the fuel pump module.
  9. Squeeze the fuel vent line retainer and remove the vent line from the fuel pump module. toy_car_cor-02-04fuelpump1.gif

  10. Remove the 8 fuel pump module retainer ring mounting screws and remove the retainer ring ('02-'04).
  11. Remove the fuel pump module retainer using special tool 09808- 14020 or equivalent (except '02-'04).
  12. Remove the fuel pump module.
To Install:
  1. Install a new O-ring on the fuel tank.
  2. Install the fuel pump module into the fuel tank.
  3. Use the following procedure to install the fuel pump module retainer ring (except '02-'04). Fuel pump module installation toy_cor-05-18-1203.gif

    1. Align the notch in the fuel tank with the tab in the module.
    2. Matchmark a new retainer with the fuel tank.
    3. Using the special tool install and tighten the retainer ring 2 revolutions.
  4. Use the following procedure to install the fuel tank module retainer ring ('02-'04).
    1. Install the retainer ring on the fuel pump module.
    2. Fasten the retainer with the 8 mounting screws. Tighten 53 in lb (6 Nm).
  5. Install the vent line to the pipe until the fuel vent line connector clicks into place.
  6. Install the fuel line with the U-clip.
  7. Install the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Install the floor service cover with butyl tape ('02-'04).
  9. Install and secure the rear floor service cover with the mounting screws (except '02-'04).
  10. Install the rear seat cushion.
  11. Connect the battery ground cable.
  12. Check for fuel leaks.
prev.gif next.gif

Oct 16, 2010 | 2005 Toyota Corolla

3 Answers

Where is fuel pump


Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:
  5. While holding the modular fuel sender assembly down, remove the snapring, if equipped or if equipped with a cam lock ring use Fuel Sender Lock Nut Tool J-39765 to press down and rotate the cam lock ring to remove it.
    WARNING If the modular fuel sender assembly is retained by a snapring, it may spring up from its position. When removing the modular fuel sender from the tank, be aware that the reservoir bucket is full of fuel. It must be tipped slightly during removal to avoid damage to the float.
    Fuel sender assembly External fuel strainer Connector retainer from the wiring harness and the fuel pump
  6. Gently release the tabs on the sides of the fuel sender at the cover assembly. Begin by squeezing the sides of the reservoir and releasing the tab opposite the fuel level sensor. Move clockwise to release the second and third tab in the same manner.
  7. Remove or disconnect the following:
    Fuel pump electrical connection by lifting the cover assembly Baffle and pump assembly from the retainer by rotating the fuel pump baffle counterclockwise Fuel pump outlet by sliding it out of slot Fuel pump outlet seal
To install:


88dac81.jpg
Fig. Exploded view of the fuel sender assembly mounting to the tank


4a62e9e.jpg
Fig. Exploded view of the fuel pump assembly
  1. Install or connect the following:
    NOTE Gently pull on the fuel pump reservoir to assure it is secure. If not secure, replace the entire fuel sender.
    Fuel pump outlet with a new seal by sliding it in the reservoir cover slots Fuel pump and baffle assembly onto the reservoir retainer by rotating it clockwise until seated Lower retainer assembly partially into the reservoir by aligning all 3 sleeve tabs and pressing the retainer onto the reservoir making sure all 3 tabs are firmly seated
    Connector retainer to the wiring harness and the fuel pump External fuel strainer Snapring, if equipped to the retainer slots while holding the modular fuel sender assembly down or use Fuel Sender Lock Nut Tool J-39765 in order to install the cam lock ring Fuel tank Negative battery cable
  2. Pressurize the fuel system and verify no leaks.

Hope helps (remember rated and comment this).

Aug 11, 2010 | 2001 Pontiac Grand Am SE

2 Answers

Need to know how to change a fuel pump on a 98 dodge caravan..



Removal

Remove fuel filler cap and perform Fuel System Pressure Release procedure.
  1. Disconnect negative cable from battery.
  2. Insert fuel siphon hose into fuel filler neck and push it into the tank.
  3. Drain fuel tank dry into holding tank or a properly labeled GASOLINE safety container.
  4. Raise vehicle on hoist.
  5. Use a transmission jack to support the fuel tank. Remove bolts from fuel tank straps. Lower tank slightly.
  6. Clean area around fuel tank module and tank to keep dirt and foreign material out of tank.
  7. Disconnect fuel lines from fuel pump module by depressing quick connect retainers with thumb and fore finger
  8. Slide fuel pump module electrical connector lock to unlock.
  9. Push down on connector retainer and pull connector off module.
  10. remove plastic locknut counterclockwise to release pump module
  11. Carefully remove pump module and O-ring from tank
  12. Discard old O-ring.

INSTALLATION
  1. Wipe seal area of tank clean and place a new O-ring seal in position on pump.
  2. Position fuel pump in tank with locknut.
  3. Tighten locknut to 53 N·m (43 ft. lbs.)
  4. Connect fuel lines.
  5. Plug in electrical connector. Slide connector lock into position.
  6. Raise fuel tank, install bolts into fuel tank straps and tighten.
  7. Lower vehicle on hoist.
  8. Connect negative cable from battery.
  9. Fill fuel tank. Check for leaks.
  10. Install fuel filler cap.


It is believed that the fuel pump is in the fuel tank, and you have to take the tank off the vehicle to replace it.

Jul 30, 2010 | 1998 Dodge Caravan

1 Answer

Need any tips i can get on changing my fuel pump


Using a floor jack brace the gas tank while you remove the straps. With the tank braced in place remove the small screws holding the neck into the fuel door area. With someone helping slowly lower the tank while making sure the neck does not unbalance the tank. Once the tank is down remove all wires and fuel lines. Remove the retaining ring and there is your fuel pump. If possible remove and save as much gas as possible before beginning.

May 20, 2010 | 2005 Chevrolet Uplander

2 Answers

Cant get fuel pump out


  1. Remove fuel tank.
  2. Remove any dirt that has accumulated around fuel pump module retaining flange.
  3. Turn fuel pump module locking retainer ring (#1)counterclockwise using Fuel Tank Sender Wrench 310-D006 and remove fuel pump module locking retainer ring.
  4. Pull fuel pump module sender plate up out of fuel tank until locking tabs(#3) for fuel pump module are accessible. Reach through fuel pump module opening, squeeze both locking tabs together and remove fuel pump module from fuel tank.


ad367e5.gif

Apr 03, 2010 | 1999 Ford Taurus

1 Answer

How do you replace the fuel pump on a 1994 Mercury Sable Wagon ?


The fuel tank needs to be removed to replace the pump. Remove fuel from tank. The fuel filler and vent hoses need to be disconnected. The electrical connector needs to be disconnected. Unbolt tank straps(2). Lower tank down. Remove fuel lines from pump. Use a brass drift(to prevent sparks) and hammer to turn retaining ring that holds pump in tank. Install new pump with new "o" ring seal and reassemble in reverse order

Apr 01, 2010 | 1994 Mercury Sable

1 Answer

Need to know if i have to drop fuel tank to replace the fuel pump on a 2004 oldsmobile Alero or just remove the rear seat to get to it...


here are step by step instructions on the removal and installation of your fuel tank and fuel pump. please do not forget to rate and comment about your experience with fixya today.
Removal & Installation
  1. Before servicing the vehicle, refer to the precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:
  5. While holding the modular fuel sender assembly down, remove the snapring, if equipped or if equipped with a cam lock ring use Fuel Sender Lock Nut Tool J-39765 to press down and rotate the cam lock ring to remove it.

    WARNING If the modular fuel sender assembly is retained by a snapring, it may spring up from its position. When removing the modular fuel sender from the tank, be aware that the reservoir bucket is full of fuel. It must be tipped slightly during removal to avoid damage to the float.
    • Fuel sender assembly
    • External fuel strainer
    • Connector retainer from the wiring harness and the fuel pump
  6. Gently release the tabs on the sides of the fuel sender at the cover assembly. Begin by squeezing the sides of the reservoir and releasing the tab opposite the fuel level sensor. Move clockwise to release the second and third tab in the same manner.
  7. Remove or disconnect the following:
    • Fuel pump electrical connection by lifting the cover assembly
    • Baffle and pump assembly from the retainer by rotating the fuel pump baffle counterclockwise
    • Fuel pump outlet by sliding it out of slot
    • Fuel pump outlet seal
To install:
Install or connect the following:
    • Fuel pump outlet with a new seal by sliding it in the reservoir cover slots
    • Fuel pump and baffle assembly onto the reservoir retainer by rotating it clockwise until seated
    • Lower retainer assembly partially into the reservoir by aligning all 3 sleeve tabs and pressing the retainer onto the reservoir making sure all 3 tabs are firmly seated

    NOTE Gently pull on the fuel pump reservoir to assure it is secure. If not secure, replace the entire fuel sender.
    • Connector retainer to the wiring harness and the fuel pump
    • External fuel strainer
    • Snapring, if equipped to the retainer slots while holding the modular fuel sender assembly down or use Fuel Sender Lock Nut Tool J-39765 in order to install the cam lock ring
    • Fuel tank
    • Negative battery cable
  1. Pressurize the fuel system and verify no leaks.

Apr 17, 2009 | Oldsmobile Alero Cars & Trucks

Not finding what you are looking for?
1996 Chrysler Cirrus Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...