Question about 1997 Ford Expedition

1 Answer

How do I get to the bank 1 front oxygen sensor. I can see but I don't know how to get to the wiring harness or how to get the socket in to remove the sensor.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 22,306 Answers

Use a ring spanner ,its easier

Posted on Jul 17, 2010

  • corymann Jul 17, 2010

    Still, how do I get into such a tight area and pull the wire harness, and then be able to put a new one in?

  • Colin Stickland
    Colin Stickland Jul 18, 2010

    thats why us mechanics are alway thin ,old adage if its in the way remove it .the wiring no doubt disconnects from elsewhere and has about a foot of wire on it ,if its a universal sensor your fitting then you will have to cut the wire anyway and put a block screw type connector inline.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 tl type s where is bank 2 sensor 1 oxygen sensor located. What is the replacement number of a sensor to kill Emission p0171 Notice and light


Oxygen sensors monitor the exhaust stream, comparing the oxygen content in it to the oxygen content of ambient air. When oxygen content is low, sensor voltage is high. When oxygen content is high, sensor voltage is low. The voltage created by the sensor is sent to the DME (engine control module) to help maintain a proper fuel mixture. The mixture preparation is used to keep the catalytic converters running at peak efficiency. The oxygen sensors used in E60 models covered in this article has four wires. Two of which are for oxygen sensor heating and two for the signal. The heater is used to get the sensor online faster. Previously, exhaust heat was used. One wire supplied a ground to the sensor for the signal, and the other was for the sensor signal.
Oxygen sensors should be replaced every 100,000 miles. In a perfect world that would be it. Wait until a specified mileage and replace the sensor. However, these sensors fail prematurely, set oxygen sensor fault codes and reduce fuel economy. In this article, I will show you how to identify the location of all four oxygen sensors and how to replace them. You will need an oxygen sensor socket to remove the sensors and remember to always work with a cool exhaust. Oxygen sensors are fragile. Do not drop, as damage may occur. Also, keep the sensor tip clean when reinstalling.
Oxygen sensors are laid out in banks, which refer to cylinders and in sensor numbers referring to before or after the catalytic converter. Bank1 or B1 refers to cylinders 1-3. Bank 2 or B2 refers to cylinders 4-6. Sensor 1 or S1 refers to the sensor before the catalytic converter. Sensor 2 or S2 refers to the sensor after the catalytic converter.
Remember that your car may have been serviced before and parts replaced with different size fasteners used in the replacement. The sizes of the nuts and bolts we give may be different from what you have so be prepared with different size sockets and wrenches.
Protect your eyes, hands and body from fluids, dust and debris while working on your vehicle. If working with the electrical system, disconnect the battery before beginning. Always catch fluids in appropriate containers and properly dispose of any fluid waste. Recycle parts, packaging and fluids when possible. Never work on your vehicle if you feel the task is beyond your ability.
Our vehicle may vary slightly from yours as models do change and evolve as they grow older. If something seems different, let us know and share your info to help other users. Do you have questions or want to add to the article? Leave a comment below. When leaving a comment, please leave your vehicle information.
Figure 1 Bank 1 Sensor 1 is indicated by a yellow arrow. Bank 2 Sensor 1 is pointed out with a green arrow. Large Image ' Extra-Large Image
Figure 2 Bank 1 Sensor 2 has a green arrow. Bank 2 Sensor 2 is shown with a yellow arrow. Large Image ' Extra-Large Image
Figure 3 Replacing sensors before catalytic converter: Oxygen sensors are located in the exhaust manifold. Remove the engine covers. See our tech article on engine covers removing. Locate the oxygen sensor electrical connectors at the right side of the engine above the exhaust manifold. Label or mark the wiring harness to aide during reinstallation. I suggest replacing one sensor at a time so you do not mix up connectors. Using an oxygen sensor socket, loosen the oxygen sensor connection to the exhaust manifold. Do not unscrew yet. Large Image ' Extra-Large Image
Figure 4 Replacing sensors before catalytic converter: Pull the wiring harness out of the mounts (green arrows) along the valve cover. Bank 1 sensor 1 shown, bank 2 sensor 1 is similar. Large Image ' Extra-Large Image
Figure 5 Replacing sensors before catalytic converter: Next, disconnect the electrical connector of the oxygen sensor you are replacing (yellow arrow). First, remove the electrical connector from the mounting bracket (green arrow) by pulling straight up. Once out, disconnect the electrical connector by pressing the release tab and pulling it apart. Note the wiring harness color and the factory sensors color code sensors to help when replacing. Locate the color of the sensor you loosened. Using an oxygen sensor socket, remove the oxygen sensor from the exhaust manifold. Lightly coat the new oxygen sensor thread with anti-seize compound. Install the new oxygen sensor and tighten to 50Nm (37 ft-lb). Then reroute the wiring harness and connect the electrical connector. Repeat if replacing both sensors. Then reassemble the engine covers and clear any engine fault codes using a BMW scan tool. Large Image ' Extra-Large Image
Figure 6 Replacing sensors after catalytic converter: Oxygen sensors are located in the exhaust, behind the catalytic converters. Working below the transmission, remove the transmission splash shield. See our tech article on lower splash shield replacing. Using an oxygen sensor socket, remove the oxygen sensor connection to the exhaust manifold. When reinstalling the sensor, do not allow the harness to remain twisted (green arrow). Be sure it is properly routed and tension free. Large Image ' Extra-Large Image
Figure 7 Replacing sensors after catalytic converter: Next, disconnect the electrical connector of the oxygen sensor you are replacing. First, remove the electrical connector from the mounting bracket (green arrow) by pulling it straight out toward the left side of the engine. Once out, disconnect the electrical connector by pressing the release and pulling it apart (inset). Note the wiring harness color, factory sensors color code sensors to help when replacing. Locate the color of the sensor you loosened. Using an oxygen sensor socket, remove the oxygen sensor from the exhaust manifold. Lightly coat the new oxygen sensor thread with anti-seize compound. Install the new oxygen sensor and tighten it to 50Nm (37 ft-lb). Large Image ' Extra-Large Image
Figure 8 Then reroute the wiring harness and connect the electrical connector. Repeat if replacing both sensors. Then reassemble the engine covers and clear any engine fault codes using a BMW scan tool.

Jan 02, 2018 | Cars & Trucks

1 Answer

I have the check engine light on and the scan read P0135 error - what is this?


P0135 code is: Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)

This code refers to the front oxygen sensor on Bank 1.

The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.

Symptoms: You will likely notice poor fuel economy the illumination of the MIL.

Causes: A code P0135 may mean that one or more of the following has happened: O2 Heater element resistance is high Internal short or open in the heater element O2 heater circuit wiring high resistance open or short to ground in the wiring harness.

Possible Solutions: Repair short or open or high resistance in wiring harness or harness connectors Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)

Dec 29, 2015 | 2006 Ford Focus ZX3

2 Answers

Check engine light is on and i got error code p1133. what is that?


Faulty Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1
- Vacuum leak
- Faulty Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 harness is open or shorted
- Faulty Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 circuit poor electrical connection

The Powertrain Control Module (PCM) monitors the Heated Oxygen Sensor (HO2S) activity for 90 seconds after closed loop operation has begun. The PCM determines if the front HO2S is functioning properly by counting the number of HO2S-1 Lean/Rich (L/R) and Rich/Lean (R/L) switches.

If the Powertrain Control Module (PCM) determines that the front HO2S did not switch enough times, the PCM will set the P1133 code.

replace the o2 sensor

Dec 14, 2013 | 2006 Saturn Vue 2.2

1 Answer

1998 nissan altima trouble code p0135


The code P0135 means O2 sensor heater circuit malfunction bank 1 sensor 1. This means you most likely have a bad O2 sensor. The possible causes are:

TT - Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit fuse
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit poor electrical connection
- Faulty Engine Control Module (ECM) Usually the code indicates a bad Oxygen sensor, but an intake vacuum leak or a failing fuel pump can cause the code, so check your intake vacuum hose for a leak or hole. But most likely, you have a faulty Oxygen sensor. Now Bank 1 Sensor 1 means the bad O2 sensor is the one on the number one cylinder side (which is the cylinder closest to the timing belt or where all your belts and pulleys are),which is bank one. If you look really closely, you will see that the number 1 cylinder is just a little bit closer to the belts than the number 2 cylinder. Now that you know which side you are dealing with, the next step is which sensor. There are two O2 sensors on each side (upstream or downstream), four total. Sensor 1 is the upstream sensor, which is before the catalytic converter closest to the exhaust manifold. Number 2 sensor is on or after the catalytic converter. So in short, you are replacing the O2 sensor on the Number 1 cylinder side before the catalytic converter. They are a pain to remove. Get some Pb Blaster lubricating oil and spray on the threads and let sit for 10 minutes and spray it again. You will need a 7/8 Oxygen sensor removal socket to remove it. Don't forget to disconnect negative battery terminal and O2 wire harness first.. Any questions please feel free to email me. Good luck.

Nov 30, 2013 | 1998 Nissan Altima

1 Answer

P0131 sabb 93 2001 po121 error codes


P0131 - O2 Sensor Circuit Low Voltage Bank 1 Sensor 1 (sensor is before the catalytic converter)

Possible causes- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks
P0132 - O2 Sensor Circuit High Voltage Bank 1 Sensor 1
Possible causes- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

I am not really sure what is going on here with the same O2 sensor giving these lean and rich codes, if nothing else is apparent and the engine runs well you may have a defective O2 sensor.

Sep 13, 2012 | Saab 9 3 Cars & Trucks

1 Answer

Codes p0132 service engine soon light on


P0132 FORD - O2 Sensor Circuit High Voltage Bank 1 Sensor 1Possible causes- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

Jun 29, 2012 | 2004 Ford F150

1 Answer

What is diagnostic procedures for DTC p0135 & p0141


Oxygen Sensor problems... P0135 (Bank 1, Sensor 1) and P0141 (Bank 1, Sensor 2)

P0135 - Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)
This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it.

The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.

Symptoms: You will likely notice poor fuel economy the illumination of the MIL.

Causes: A code P0135 may mean that one or more of the following has happened:
O2 Heater element resistance is high
Internal short or open in the heater element
O2 heater circuit wiring high resistance
open or short to ground in the wiring harness

Possible Solutions:
Repair short or open or high resistance in wiring harness or harness connectors
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)



P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)
This code means that the heated circuit in the oxygen sensor on bank 1 decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0141.

Symptoms: You will likely notice poor fuel economy the illumination of the Check Engine Light.

Causes: A code P0141 may mean that one or more of the following has happened:
open or short to ground in the wiring harness
O2 heater circuit wiring high resistance
O2 heater element resistance is high
Internal short or open in the heater element

Note: Typically a failed catalytic converter does not cause this code. You're more likely to see a P0420 code for a failed converter.

Possible Solutions:
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)
Repair short or open or high resistance in wiring harness or harness connectors


Hope this helps (remember to rate this answer)..

May 11, 2011 | 2000 Nissan Maxima

1 Answer

What is p1148


P1148 - Closed Loop Control Function Bank 1
This mean that the closed loop control function for bank 1 does not operate even when vehicle is driving in the specified condition.

The Powertrain Control Module (PCM) or Electronic Control Module(ECM) monitor the function of the Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor by comparing the signal with the Rear O2 sensor.

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes:
- Harness or connectors Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor 1 circuit is open or shorted.
- Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor bank 1
- Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor bank 1 heater

Possible solution:
- Repair harness or connector. If repair is needed
- Replaced Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor bank 1


Then, possible causes are faulty harness or connectors to the air fuel ratio sensor, a faulty air fuel ratio sensor (1) or faulty air fuel ratio sensor (1) heater. Most likely yes it is just faulty sensor. Just replace this devices and reset the stored codes.

Keep us updated.

Feb 10, 2011 | 2005 Nissan Altima

1 Answer

Hard running motor trouble shooting codes p0135


P0135 - Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)

This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.

Symptoms: You will likely notice poor fuel economy the illumination of the MIL.

Causes: A code P0135 may mean that one or more of the following has happened:
* O2 Heater element resistance is high
* Internal short or open in the heater element
* O2 heater circuit wiring high resistance
* open or short to ground in the wiring harness

Possible Solutions:
* Repair short or open or high resistance in wiring harness or harness connectors
* Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)


I hope this helps, remmeber to rate and comment this.

Oct 05, 2010 | 1998 Chevrolet Blazer

1 Answer

Where Are The sensor Banks On The 2004 GC


Grand Cherokee oxygen sensor locations for 4.0 and 4.7 engines

510d5d9.jpg


f8b5293.jpg


Four wires (circuits) are used on each O2 sensor:

  • 12–volt feed circuit for the sensor heating element
  • Ground circuit for the heater element
  • Low-noise sensor return circuit to the PCM
  • Input circuit from the sensor back to the PCM to detect sensor operation

O2S Sensor removal Never apply any type of grease to the oxygen sensor electrical connector, or attempt any soldering of the sensor wiring harness.
WARNING: THE EXHAUST MANIFOLD, EXHAUST PIPES AND CATALYTIC CONVERTER(S) BECOME VERY HOT DURING ENGINE OPERATION. ALLOW ENGINE TO COOL BEFORE REMOVING OXYGEN SENSOR.
1. Raise and support vehicle.
2. Disconnect O2S pigtail harness from main wiring harness.
3. If equipped, disconnect sensor wire harness mounting clips from engine or body.
CAUTION: When disconnecting sensor electrical connector, do not pull directly on wire going into sensor.
4. Remove O2S sensor with an oxygen sensor removal and installation tool.

02S Sensor installation
Threads of new oxygen sensors are factory coated with anti-seize compound to aid in removal. DO NOT add any additional anti-seize compound to threads of a new oxygen sensor.
1. Install O2S sensor. Tighten to 22 ft. lbs. (30 N·m) torque.
2. Connect O2S sensor wire connector to main wiring harness.
3. If equipped, connect sensor wire harness mounting clips to engine or body. When Equipped: The O2S pigtail harness must be clipped and/or bolted back to their original positions on engine or body to prevent mechanical damage to wiring.


Hope thats help (remember comment and rated this).

Apr 29, 2010 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Ford Expedition Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5636 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...