Question about 2007 Fiat X1/9

Open Question

Insturment cluster 2009 international durastar 300hp max force stopped working (temp, oil, speedo,tech, fuses and relay ok in fuse box emc fuses engine fuses off battery ok) . is there a relay i dont know or find?the headlight and panel light board has been replaced but did not fix the cluster has nothing nor do headlights clearance must be tripped with the windsheild wiper switch (if u know these trucks u will know wjhat i,m saying) help does the cluster need replacing

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: The insturments on the dash

I had a similar problem several years ago with my 1993 Dodge intrepid. None of the instruments on the dash would work. When this would happen the transmission would not shift past second gear. My heater blower was Not running all the time. What I found was the wiring harness to the ignition switch did not have enough slack in it. This was causing the ignition switch plug to randomly lose contact with the ignition switch. The first thing you need to do is remove the steering column covers. Put the tilt steering all the way up. Look under the steering column cover. There are 2 phillips head screws and 3 recessed T-10 torx tip screws that hold the 2 halves of the cover together and to the steering column. Remove all 5 screws. The handle used to tilt the steering wheel also has to be removed. You will need a T-30 torx tip to remove it. Now carefully remove the bottom half of the cover. The ignition switch wiring harness is under the steering column. I just reached in under the column and gently pulled on the harness until it had a little slack when I left go. Make sure the ignition switch plug is plugged in all the way. You might even want to unplug it and plug it back in several times just in case a slight film of corrosion has accumulated on any of the electrical terminals. This will help clean it off. You could also look inside the plug to make sure none of the terminals are bent or pushed part way out the back. I hope this solves your problem. Mine has not reoccurred in the 8 years since I did this.

Posted on Apr 11, 2011

Ad
matt_sams
  • 124 Answers

SOURCE: no power to fuses on Fiat 14 ducato van (1987) alternator charging, headlights, horn, hazard all ok, no power to indicators, wipers, heater fan, fuel gauge, temp gauge. all fuses are ok, engine starts

Sounds like the relay is bad, look in the fuse panel or under the dash for a lil black box, they are usually appx 1"' x 1" and there should be several of them. You may want to check owners manual or a repair manual to find the location. They should be listed in the schematic of the fuse box as well.

Posted on Jun 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of the Insturment cluster fuse. 2003 Acura MDX


Check 10A FUSE 9 in the driver's under-dash fuse/relay box and 7.5A FUSE 13 in the passenger's under-dash fuse/relay box.

Dec 30, 2016 | Cars & Trucks

1 Answer

My speedo, rev counter, fuel guage and temp guage have all stopped working on my 2002 focus 2.0 ltr ghia. All fuses are ok. Any ideas of what could be the problem ?


The instrument cluster is a hybrid electronic cluster (HEC) with two basic configurations, the base cluster and the optional instrument cluster. In addition to the two basic configurations, the SVT uses a modified optional cluster in combination with a separate oil pressure and oil temperature cluster. The base instrument cluster, optional instrument cluster and the oil pressure and oil temperature cluster receive and output information utilizing both hardwired circuitry and the standard corporate protocol (SCP) or the controller area network (CAN) communication network (2.3L only). It is very important to understand:
  • where the input originates from.
  • all the information necessary in order for a feature to operate.
  • which module(s) receive(s) the input or command message.
  • does the module which received the input control the output of the feature, or does it output a message over the SCP or CAN network to another module?
  • which module controls the output of the feature. Its more then likely you need a new instrument cluster.

Dec 19, 2014 | Cars & Trucks

1 Answer

Instruments don't work, key stuck in ignition, doesn't shift correctly


Sounds like you need a new car.
With joking aside, the problem with your speedo, tach, gas guage, temp gauge and odometer can probably be one of two things. Check your fuses. If they are fine you may need to replace your cluster panel. I had to have the entire thing changed over my speedo not working right. It was not cheap. You might want to check the relay box under the hood. Does your transmission leak? Check the fuses and relay on it also. Get a new ignition switch and replace the old one if your key is stuck. You can try WD40 on that key but don't expect any miracles. The bearings are likely shot. Sorry I posted all of this bad news. Good luck.

Jan 05, 2014 | 1998 GMC Jimmy

1 Answer

My taillights and dash lights just quit working I have brake lights and turn signals


check your fuses, bulbs, and relays for the taillights and insturment cluster, normally when lights go out randomly its due to a bad fuse or relay or bulbs

Aug 31, 2011 | 1996 Pontiac Sunfire

1 Answer

Abs light comes on and my hole insturment cluster stops working


i would have someone to hook up a abs diagnostic tester to see what the abs system is saying, it is definitely telling you that the abs system has located a problem, also check your fuses and relays in the black box under your hood , on the drivers side.

Apr 18, 2011 | 2000 Dodge Caravan

1 Answer

Turn signal, tachometer, fuel and temp guage stopped working


you should pull out the gauge cluster and check the connector on the back side of the cluster.. i bet that is the issue

Jul 18, 2009 | 1989 Honda Accord 4 Door

1 Answer

Chevy cavalier 2005 speedometer stuck not working


That Cluster will work But, You will have to get an Installation kit if you want the Tach to work. Everything else will hook up the Same. You have a Distribution Box (Fuse Box) Under the Hood on the Drivers Side, There is a Fuse in it for the Speedo. Inside the Cover to the Box is the Fuse Diagram or in the Back of the Owners Manual.

Jan 08, 2009 | 1991 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Marvin
Marvin

Level 3 Expert

83810 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...