Question about 2000 Kia Sephia

Open Question

2000 kia sephia how to get to the ac expansion valve. need diagrams to help. thanks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 132 Answers

SOURCE: I need to rplace tke power steering hose on a 2000 kia sephia

yes put some thread tape around the thread of the new hose before screwing in for much tighter seal since under fairly high pressure and when taking old hose off have clean rags ready to block the fluid from pouring out everywhere and when you have replaced hose start car check power steer oil level and look at hose to make sure not leaking if it is tighten hoses just a little at a time until leak stops

Posted on Nov 09, 2008

Ad
StormStrikes
  • 104 Answers

SOURCE: Transmission fluid capacity for 2000 Kia Sephia?

The four speed automatic shows a total fill (that is all the fluid it can hold) is 5.7 Quarts. So if you just dropped the pan and relplaced the filter, you shouldnt need more than 4 quarts and likely you would have a little extra with that.

Posted on Dec 30, 2008

  • 3 Answers

SOURCE: 2000 kia sephia clutch

this is a big job for someone who is not mechanically inclined but....here it goes go buy a new clutch new tranny fluid and a haynes manual at the auto parts store your going to have to drain and drop your tranny ... BUY THE CLUTCH WITH THE TOOL theres an alignment tool needed to align the plates n bearings start by pulling off both tires, brakes and both cv axels be sure to remove the intermediate shaft from the tranny on the passenger side (should come out with the axel passenger side only) so do yourself a favor and buy an impact gun with at least 500 ft lbs torque youll need it also have handy your 14mm 17mm and 19mm impact sockets and remember this job usually runs around 1,200 bucks at firestone also DO NOT remove the bolt in the middle of the front springs under the hood just the four around it and the will pop out no prob and wont need to be clamped remove the starter behind your engine its under the oil filter also if your new to this sorta thing its gonna take you about 3 days to do it buy the impact gun if ur in a hurry look at a pawn shop have your flywheel machined its going to be accessible and it needs it hope this helps dont forget the book which you should already have bought anyway its good for your torque specs which you will also need a torque wrench for the clutch also dont crack open ur tranny this isnt a honda

Posted on Jan 05, 2009

ZJLimited
  • 17970 Answers

SOURCE: fuse panel diagram for 1999 kia sephia

Here you have the Fuse Cover pic.

Also, here can search the Owners Manual

I hope helped with this (remember rated this help).

Posted on Dec 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need the location of the front expansion valve on a Kia Sedona 2006 if you have a picture it will help a lot thanks


Modern AC systems don't use an expansion valve, but rather an orifice tube, usually located in the high side line where it attaches to the evaporator near the firewall.

Jul 06, 2015 | Kia Cars & Trucks

1 Answer

The starter with a 2000 kia sephia


The starter is at the rear of engine where it mates to the transmission and has a large red battery cable attached to it.
See picture below.
9_13_2012_8_48_00_pm.jpg

Sep 13, 2012 | 2000 Kia Sephia

2 Answers

Where is the expansion valve located on the 2004 KIA Sedona


Kia Sedona expansion FRONT valve located under dash, behind glove box, fan and coil. Evacuate freon first. Disconnect Freon lines from firewall., Lay right front seat back to flat horizontal position and lay on top or totally remove the seat for easier working access. Remove under dash cover, fan, glove box, coil housing, remove coil mounting bolts, remove old expansion valve. (Inspect old valve, if debris inside, blow out coil before installing new valve. If visible debris best to consider replacing REAR expansion valve and DRIER/FILTER in front of radiator too and blow out all lines and coils while servicing.) Use compressor oil to lubricate "O" rings on new FRONT or REAR expansion valve, install valve bolts, reinstall coil bolts to FRONT firewall or REAR frame, reconnect freon lines to firewall in engine compartment. Evacuate AC system, install freon (35 1/2 ounces, nominal 3 pounds), check system for leaks, check for proper operation, enjoy.

Sep 12, 2012 | 2004 Kia Sedona

1 Answer

I need a diagram of the spark plug wires on a 2000 kia sephia


shinehutt_5.gifshinehutt_6.gifshinehutt_7.gifshinehutt_8.gifhope this helps there are four engine types

Jan 14, 2011 | 2000 Kia Sephia

1 Answer

I need to locate the idle air control valve on my 2000 kia sephia 1.8 L


IDLE AIR CONTROL VALVE IS CONNECTED TO THE THROTTLE BODY.

Dec 05, 2010 | 2000 Kia Sephia

1 Answer

How do you tighten (which bolts)the fan belt and power steering belt


Hello lubyamanda and thank you for asking your question here on fixya.com.

I have actually written a general information article that will walk you through the general process of changing the fan belt on your
2000 Kia Sephia. It will also point you to the resources you need for getting the diagrams of how the belt needs to go back on. Belts usually cost less than $20 and take a few minutes to put them on.

Here is a link to that article:
How to change the fan belt on your
2000 Kia Sephia

If this has helped you in any way, then feel free to follow my Twitter account for more great money saving tips and tricks. twitter.com/acoates23234
I follow back, too. :)

Thanks for reading.

Aug 15, 2010 | 2000 Kia Sephia

1 Answer

Need diagram for 2000 kia sephia wiring harness to the radio


i found one in a haynes book covers sephia and spectra 94 to 04 .i have no idea how to scan this an attach . theres not much to the diagram you have an audio 10A fuse hot in acc or run grn wire .you also have a room fuse 10A hot at all times pnk wire .both are in the i/p fuse block . in the fuse relay box you also have tail lh fuse 10A hot with lights on blu/wht wire the rest is just radio to speakers and antena . wish i could be more help

Aug 07, 2010 | 2000 Kia Sephia

1 Answer

How do you replace fan belt on a 2000 Kia Sephia?


Hello smg86 and thank you for asking your question here on fixya.com.

I have actually written a general information article that will walk you through the general process of changing the fan belt on your
2000 Kia Sephia. It will also point you to the resources you need for getting the diagrams of how the belt needs to go back on. Belts usually cost less than $20 and take a few minutes to put them on.

Here is a link to that article:
How to change the fan belt on your
2000 Kia Sephia

If this has helped you in any way, then feel free to follow my Twitter account for more great money saving tips and tricks. twitter.com/acoates23234
I follow back, too. :)

Thanks for reading.

Apr 15, 2010 | 2000 Kia Sephia

Not finding what you are looking for?
2000 Kia Sephia Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...