Question about 1999 Honda Accord

1 Answer

I need to remove the front plate in my honda to get the stereo out I had installed. I removed bottom screws and it will lift up but the top seems to be secured in the middle. Can you help

Posted by on

  • huch3 Jul 17, 2010

    VERY

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 6,826 Answers

Http://www.installdr.com/InstallDocs/Honda/PDF/466053.pdf

The above is a good guide I found for removing the radio. here are 3 screws, it says.

Posted on Jul 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

To remove 1993 mustang conv. top cylinders should top be up or down? thanks, bill


don't have 93. here's 94

Motor Assembly, Convertible Top Removal and Installation
NOTE: The folding top hydraulic cylinder rods should be in the fully retracted position.
Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove motor and pump assembly as outlined.
  1. Loosen each folding top motor upper and lower hose fitting on the sides of the folding top hydraulic lift motor and plate kit (533A00) .
  1. Remove the folding top hydraulic lift motor and plate kit .
  1. Remove each of the service folding top hydraulic lift motor and plate kit plugs one at a time and attach the tee fitting to the replacement folding top hydraulic lift motor and plate kit . NOTE: Make sure that the o-ring is installed in the bottom of each folding top hydraulic lift motor and plate kit port before attaching the hose tee fitting.
  1. Connect the folding top hydraulic lift motor and plate kit unit to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the folding top motor upper and lower hoses (53390) . Some noise squeal may be noticed due to the air. srb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not overfill or the reservoir seal could be blown out.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.
-------------------------------------------------------------------------------------------------------------------------------
Section 01-17: Convertible 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Lift Cylinder, Power Top Removal and Installation
NOTE: The cylinder rods should be in the fully-retracted position.
  1. Remove pump and motor as outlined.
  1. Remove the upper and lower hose fitting from the folding top hydraulic cylinder (50600) . Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove each of the service cylinder plugs one at a time and attach the hose fittings. NOTE: Be sure each fitting is installed in the correct position on the folding top hydraulic cylinder .
    NOTE: Make sure that the tetra seal is installed in the bottom of each of the folding top hydraulic cylinder ports before attaching the upper and lower hose fittings.
  1. Connect the folding top hydraulic lift motor and plate kit (533A00) to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the hoses. Some noise squeal may be noticed due to the air.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.

Jan 21, 2011 | Ford Mustang Cars & Trucks

1 Answer

I needed to replace climate control unit on1997 Grand Am GT. Concerned with how to remove the cluster face panel w/o breaking it.


Let me know if this helps out.

Heater & Air Conditioning
  1. Disconnect the negative battery cable.
  2. Remove the screws securing the cluster trim plate to the instrument panel.
  3. Tilt the top of the cluster trim plate downward releasing the clips that mount the bottom of the trim plate to the dash. Remove the trim plate.
  4. Remove the screws attaching the accessory trim center plate to the dash.
  5. Tilt the top of accessory trim plate downward releasing the clips that mount the bottom of the plate to the instrument panel. Remove the plate.
  6. Remove the screws attaching the control assembly to the dash.
  7. Remove the control assembly from the dash.
  8. Disconnect the control assembly electrical connectors.
  9. Remove the control assembly.

To install:

  1. Install the control assembly.
  2. Connect the control assembly electrical connectors.
  3. Install the control assembly attaching screws.
  4. Push the mounting clips into place and roll the top of the accessory trim plate upward into position.
  5. Install the screws attaching the accessory trim plate to the dash.
  6. Push the mounting clips into place and roll the top of the cluster trim plate upward into position.
  7. Install the screws attaching the cluster trim plate to the instrument panel.
  8. Connect the negative battery cable.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 40; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Jan 23, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

How do you replace window regulator on 1994 honda


hello there:
to replace the window regulator you will need too look for screws around the sides and bottom of the door panel then you will need to remove the door handle backing plate and the door handle where you grab too close it you see no screws there will be a round cap you will need to take out to see the screw head remove the screws and lightly pull the door panel out there will be body clips that will come out of the door then slide door panel up and pull off this will give you access to the regulator remove the bolts on the regulator and remove install in reverse hope this help you out please leave a review thanks sincerely D.Jones

Jun 03, 2010 | 1994 Honda Passport

1 Answer

How do you remove the front blower motor for a 2004 Chrysler Town & Country? It seems to have some bolts far up behind the housing which seems impossible to remove.


Follow your vehicle's service manual procedures for blower motor removal. The following are general removal procedures:
  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.

May 22, 2010 | 2004 Chrysler Town & Country

1 Answer

Diagram on how to take off left door panel on 1998 ford expedition


REMOVAL AND INSTALLATION Trim Panel —Front Door, Expedition Removal
  1. NOTE: Release the top portion first.
    Remove the sail panel.
cff7e48.gif
  1. Remove the window regulator switch plate (14524). 3745193.gif

  1. Disconnect the electrical connectors.
d860af8.gif
  1. Remove the upper door trim panel screw. 4b4377b.gif

  1. Remove the door trim panel screw at the window regulator switch plate opening. 149d0a6.gif
  1. Remove the door trim panel screw in the courtesy lamp housing.
    1. Remove the courtesy lamp lens.
    1. Remove the screw. 8fe707b.gif

  1. Remove the inside door handle trim cover. 52f3d0f.gif
  1. Remove the inside door handle.
    • Remove the bolt. abe462f.gif
  1. swj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the front door trim panel, do not pull directly outward.
    Lift upward and then outward to remove the front door trim panel (23943). d6459fb.gif
  1. Remove the courtesy lamp and socket. dfb380f.gif
  1. Disconnect the power mirror electrical connector.
Installation
  1. Connect the power mirror electrical connector.
  1. Install the courtesy lamp and socket.
  1. Install the front door trim panel.
  1. Install the inside door handle.
    • Install the bolt.
  1. Install the inside door handle trim cover.
  1. Install the door trim panel screw in the courtesy lamp housing.
    1. Install the screw.
    1. Install the courtesy lamp lens.
  1. Install the door trim panel screw at the window regulator switch plate opening.
  1. Install the upper door trim panel screw.
  1. Connect the electrical connectors.
  1. NOTE: If a new trim panel is required: Some new trim panels have a cut out opening for the window switchplate that is larger than that on the original trim panel. When installing a new trim panel, install the window switchplate in the following sequence to make sure that the switchplate is secured fully into the door trim panel.
    Install the window regulator switchplate.
    • Insert the rear switchplate clip into the trim panel opening.
    • Install the forward and side clips into the trim panel opening.
  1. NOTE: Install the lower portion first.
    Install the sail panel.

Mar 14, 2010 | 1998 Ford Expedition

1 Answer

How do I replace the climate control on 97 Buick Riviera? I have the replacement but I'm unsure of how to get the dash off?


i have a 95 and the way i took the dasy off is, under neath the lip of the dash there is a plastic plate that goes accross the whole dash there is plastic pins in there u have to remove i used a flat head screw driver but they might break. then there is several screws that connect the top of the dash to the front of the console remove them screws when u remove them there is 2 more screws one of them is on the drivers side u have to remove the the whole fuse panel and there is the same thing on the pass side once all the screws are out u have to lift the bash board to remove the console now this is were it gets trickey cause it is hard to lift the dash doard cause it only goes so far cause of the airbag but just work at it and lift the console out not the climate control is exposed. there is 2 screws at the bottom and then there is one way in the back top center. then the climate control will come out disconect the wires on the right side and insert the new one. i did not put top screw back in cause it was almost inpossibe with out a maginatic screwdriver. with the top screw out thereis no difference in operation and it does not move in the console. once u get that in its tome to put the console back on but the stering wheel all the way down and insert bottom first and take your time cause this is the hardest part but it will evently go back in and when it does make sure the taps on the console are behind the ones on the dash board screw in all the screws and put the plate back on with the plastic clips. and make sure the screws are tight other wise the dash board will make noise like mine does. and just so u know is seems harder then what it looks

Feb 01, 2010 | 1997 Buick Riviera

1 Answer

How do I remove the radio


Detach the negative battery cable (if your radio is anti-theft, make sure you have the code).
Remove the floor console (front and rear retaining screws, then you can probably lift the console over the shift lever if you move the lever to one of the drive positions. I say probably, because Honda says that if the car is an automatic it is recommended that you remove the shift knob by removing the two shift knob screws and pull the knob and the slider. If it’s not automatic, you just unscrew and remove the shift knob.)
Detach the console and lift it out.
Remove the ashtray and the ashtray holder. There are three screws (two vertical in front and one horizontal in back).
Remove the two retaining bolts in the roof of the ashtray cavity which retain the small storage box beneath the stereo (the box and the stereo are attached to one another), then pull out the stereo and the box enough to remove the two screws on the sides of the radio so you can separate the box from the radio.
Unplug the electrical connector from the radio, and the antenna lead, then remove the radio.
Installation is the reverse.
Hope this helps you.

Nov 14, 2009 | 1992 Honda Accord

1 Answer

Ford expedition side mirror (instalation giude)


SECTION 501-09: Rear View Mirrors 2003 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel —Expedition Removal and Installation
NOTE: Left front door shown, right front similar.
  1. Remove the door handle bezel.
    • Use service notch.
  1. Remove the window control switch plate.
    • Use service notch and disconnect the electrical connectors.
  1. s3j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    Remove the two bolts and three screws, and remove the door trim panel.
  1. Remove the weather shield.
  1. Disconnect the exterior mirror electrical connector.
  1. Remove the exterior mirror.
    • Remove the nuts.
cf86471.gif
  1. To install, reverse the removal procedure.
    • Install top nut first.
---
Exterior Mirror Motor Removal and Installation
  1. Position the mirror glass to obtain a gap at the top edge of the mirror and carefully pull the top edge of the glass away from the mirror housing.
  1. Disconnect the heated mirror electrical connectors.
  1. Remove the exterior mirror motor screws and exterior mirror motor.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.

Oct 26, 2009 | 2003 Ford Expedition

1 Answer

How do I remove the interior door panel on my 1992 Honda Accord? I'm wanting to replace a few parts to my power window system. Thanks! Mark


1st remove the door handle screws or screw that holds the plate up then disconnect any wires to the power switches by removing the units themselves they just pop out grab hold of the bottom and pull out from the bottom the panel it is held in place by plastic clips then lift up and off the door itself and dont forget the lock lever it just pops out as well re-installation is reverse procedure

Sep 26, 2009 | 1992 Honda Accord

1 Answer

1996 Honda Accord. Want to replace radio. How to access?


Start with the rear console. Two screws on the sides, then open the console and pry up the plate in the bottom.   Remove the screws under the plate.  Pull emergency brake lever. Remove cup holder insert. Three more screws to remove. Now the console will come out when you lift it and pull it back out of the clips. Next remove the ashtray. One screw behind the ash tray two more for the cover. Disconnect wires. the stereo is accessible. 

May 03, 2009 | 1996 Honda Accord

Not finding what you are looking for?
1999 Honda Accord Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

83081 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...