Question about 2004 Kia Optima

1 Answer

Remove ignition switch for a 2004 kia optima - 2004 Kia Optima

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kia Master
  • 6,826 Answers

Ignition Switch Removal & Installation To Remove:

  1. Disconnect battery negative cable.
  2. Disarm air bag system.
  3. Remove driver air bag module.
  4. Loosen screw and lift horn pad to remove.
  5. Remove lock nut and washer. CAUTION
    Do not hammer on steering wheel. Damage can occur to the energy absorbing portion of the steering column.
  6. Pull dynamic damper forward and lift up to remove.
  7. Remove steering wheel.
  8. Remove steering column shrouds.
  9. Remove lower cover.
  10. Remove multifunction switch.
  11. Remove entire lower portion of dash.
  12. Remove mounting fasteners and lower steering column.
  13. Remove bolts and separate ignition switch from steering column.
To Install:
  1. Install ignition switch to steering column and install bolts.
  2. Raise steering column and install mounting fasteners.
  3. Install lower portion of dash.
  4. Install multifunction switch.
  5. Install lower cover.
  6. Install steering column shrouds.
  7. Install steering wheel.
  8. Install dynamic damper.
  9. Install washer and lock nut.
  10. Lift horn pad and install screw.
  11. Install driver air bag module.
  12. Connect battery negative cable.
remove ignition switch for a 2004 kia optima - prev.gif next.gif

Posted on Jul 17, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
samson-1
  • 153 Answers

SOURCE: 2004 Kia optima blower motor switch: How to replace??

how do you know the blower switch is bad?

Posted on Oct 16, 2008

robshow
  • 367 Answers

SOURCE: 2004 Kia Optima airbag computer module

Try this website you have to register but its free.

Just click the above link to go to kiatechinfo.com

Posted on Jan 19, 2009

  • 1 Answer

SOURCE: replacing 2004 kia optima alternator

I'm not sure on the cost but I replaced mine a few weeks ago and man o man what a job!!! I had to take apart the wheel assembly on the pass side.....pull the axle...jack the engine. 1st time 10 hrs.....2nd time thanx to a fualty replacement alt. 6 hrs. Good luck

Posted on Feb 22, 2009

seans46
  • 161 Answers

SOURCE: 2004 KIA Optima LX timing belt/water pump

The thing is your doing the timing belt the water pump is right their with it . it should cost you much more at all besides the cost of the water pump. When doing a timing belt I have a rule that I go by The timing belt/seals =cam , crank , any pulley & tensioner & water pump all get replaced at the same time. I did a t-belt on a Audi A-8 very complex whole front of car has to come off as well, he didnt want to do w-pump & thermostat his thermostat was their as well not even a month later the water pump gave out he had to pay double the price because he didnt want to do it when I had it apart the first time. And make sure mechanic is ase certified . good luck

Posted on Jul 02, 2009

  • 14036 Answers

SOURCE: air conditioner 2004 kia optima

CHECK AC COMPRESSOR CLUTCH FUSE AND RELAY.MAKE SURE POWER IS GOING TO COMPRESSOR CONNECTOR.IF NO CHECK FUSE AND RELAY.IF YES.YOUR PROBLEM COULD BE AC CONTROL SWITCH BAD OR BLOWER MOTOR.COMPRESSOR CLUTCH SHORTED OR OPEN.AC PRESSURE SENSOR BAD OR REFRIGERANT IS LOW.

Posted on Jul 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 Kia Optima won't start all of a sudden. I have had starter tested, battery replaced, alternator is good. What can I do?


I had purchased its manual from online store www.reliable-store.com. Here's the site link
I am sure they will help you

Mar 04, 2018 | 2004 Kia Optima

1 Answer

Location of ignition failure sensor for a 2004 Kia Optima 2.7


ignition failure sensor ??? No such thing . Could you explain what your vehicle is doing or not doing .

Jan 07, 2017 | 2004 Kia Optima

1 Answer

How do u disable the door chime on a 2004 KIA optima


Pull the door panel off and then remove and bypass the door ajar switch inside attached to the door latch.

Aug 30, 2016 | 2004 Kia Optima

1 Answer

My 2004 Kia Optima won't start all of a sudden. I


I suggest you try one of those instant download manuals. My brother ( a mechanic) buys
it when he can't fix some technical issue He buys from www.reliable-store.com . A lot of mechanics actually do this. Website is very good for this. Must try it !!

Mar 03, 2018 | 2004 Kia Optima

1 Answer

Where is the ignition module on a 2004 Kia optima located


The ignition failure sensor (this is the module you want) has 4 wires and is located near the back of the engine close to the coils

Feb 22, 2012 | 2004 Kia Optima

1 Answer

How to replace the multi function switch on my 2004 optima kia...any demonstration/illustrations will be appreciated


Kia_Sephia_Rio_Spectra_Optima_1998-2006
Multi-Function Switch - Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the steering wheel, as outlined earlier in this section.
  3. Remove the steering column upper and lower shrouds.

    29391c9.jpg
    Fig. Remove the steering column upper (A) and lower shrouds (B)
  4. Detach the multi-function switch electrical connector(s).

    0b41ec5.jpg
    Fig. Detach the multi-function switch (A) electrical connector(s)
  5. Remove the 3 bolts, as shown, then remove the multi-function switch assembly (B).
  6. Installation is the reverse of the removal procedure.

    4bfd90f.jpg
    Fig. Remove the 3 bolts, as shown, then remove the multi-function switch assembly (B)

Hope this help (remember rated this post).

Mar 28, 2010 | 2004 Kia Optima

1 Answer

Car won't start.


ignition control module i suspect

Nov 07, 2009 | 2004 Kia Optima

2 Answers

2002 Kia Optima will not start at times


Check ignition switch, Also Did you ccheck fuel filter.

Ignition switch is probably the issue.

Dec 11, 2008 | 2004 Kia Optima

1 Answer

2004 kia optima


Try the ignition switch,

For the Crank sensor there is a small metal disc that mounts behind the sensor if that is cracked or dammaged or installed backwards you will get same results as if it wasn't Make sure the timing marks line up on your timing belt. www.kiatechinfo.com

Nov 06, 2008 | 2004 Kia Optima

1 Answer

2004 Kia optima blower motor switch: How to replace??


how do you know the blower switch is bad?

Oct 16, 2008 | 2004 Kia Optima

Not finding what you are looking for?
2004 Kia Optima Logo

1,346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...