Question about 2006 Jeep Liberty

Open Question

Fuse location in jeep liberty 2006

Looking for a fuse location in jeep liberty 2006 for the dash board. Any one got a diagram?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 137 Answers

SOURCE: Inoperable Power Window 2006 Jeep Liberty

the window regulator needs to be replaced

Posted on Jan 19, 2009

Ad
  • 9 Answers

SOURCE: 2002 jeep liberty interior fuse diagram

1-20amp-pwr outlet frt. 2-10amp-rear fog lights(export only)
3-15 amp-horn 4-10amp-hedlt low beam rt
5-10amp-hedlt low beam lft 6-20amp-bodycontrolmodule/pwr dr locks 7-spare 8-spare 9-10amp- rt pk lt /rt tail lt/trailer tow lt/cluster
10-spare 11-15 amp-flasher 12-15 amp-stop lts
13-10amp-bodycontrolmodule/cmtc/cluster 14-spare
15-10amp-pdc fuel pmp & auto shutdownrelays/skis
16-20amp-pwr outlet rear 17-15amp-rear wiper 18-20amp-radio choke relay 19-20amp-frt fog lts/trailer tow stop and turn lts
20-20amp-sunroof 21-spare 22-10amp-wiperswitch/frt and rear washer 23-10amp-lft park lt/lft tail lt 24-10amp-pdc blower motor relay 25-10amp-heatseatswitch/hvac controlhead/trailor tow battery charge 26-10amp-hedlt highbeam rt 27-10amp-hedlt highbeam lft
28-spare 29-15amp-heated seat module 30-10amp-heated mirrors/rearwindowdefrosterindicator 31-20amp-cigarlighter
32-10amp-radio/frtdoorlockswitches/bodycontrolmodule
33-10amp-skis/diagnostic connector 34-15amp-cluster/courtesy lts/radio/bodycontrolmodule/maplights/cmtc/underhood lt/vanity lts
35-spare 36-10amp-ignition run/start-orc/lft and rt siacm
37-10amp-ignition run only-orc 38-10amp-abs module/brake shift interlock solenoid 39-10amp-rear window defroster relay/flasher/backup lts

Posted on Jul 10, 2009

  • 114 Answers

SOURCE: Need a Jeep Liberty drive belt diagram.

3f6d05b.gif Here you go

Posted on Oct 15, 2009

  • 239 Answers

SOURCE: need fuse box diagram for 2005 jeep liberty

It should be on the fuse cover. Do you have your owner's manual? It should also be near the back of that.

Posted on Feb 25, 2010

moparhart
  • 245 Answers

SOURCE: I have a slow battery drain on a 2006 Jeep

Hi
Welcome
Jb power is Junction Block power
Here is a list of tests for this problom

IGNITION-OFF DRAW TEST The term Ignition-Off Draw (IOD) identifies a normal condition where power is being drained from the battery with the ignition switch in the Off position. A normal vehicle electrical system will draw from five to thirty-five milliamperes (0.005 to 0.035 ampere) with the ignition switch in the Off position, and all non-ignition controlled circuits in proper working order. Up to thirty-five milliamperes are needed to enable the memory functions for the Powertrain Control Module (PCM), digital clock, electronically tuned radio, and other modules which may vary with the vehicle equipment.
A vehicle that has not been operated for approximately twenty days, may discharge the battery to an inadequate level. When a vehicle will not be used for twenty days or more (stored), remove the IOD fuse from the Junction Block (JB). This will reduce battery discharging.
Excessive IOD can be caused by:

  1. Electrical items left on.
  2. Inoperative or improperly adjusted switches.
  3. Inoperative or shorted electronic modules and components.
  4. An internally shorted generator.
  5. Intermittent shorts in the wiring.
If the IOD is over thirty-five milliamperes, the problem must be found and corrected before replacing a battery. In most cases, the battery can be charged and returned to service after the excessive IOD condition has been corrected.
1. Verify that all electrical accessories are off. Turn off all lamps, remove the ignition key, and close all doors. If the vehicle is equipped with an illuminated entry system or an electronically tuned radio, allow the electronic timer function of these systems to automatically shut off (time out). This may take up to three minutes. See the Electronic Module Ignition-Off Draw Table for more information.
ELECTRONIC MODULE IGNITION-OFF DRAW (IOD) TABLE Module Time Out?
(If Yes, Interval And Wake-Up Input)
IOD IOD After Time Out Radio No 1 to 3 milliamperes N/A Audio Power Amplifier No up to 1 milliampere N/A Central Timer Module (CTM) No 4.75 milliamperes (max.) N/A Powertrain Control Module (PCM) No 0.95 milliampere N/A ElectroMechanical Instrument Cluster (EMIC) No 0.44 milliampere N/A Combination Flasher No 0.08 milliampere N/A 2. Determine that the underhood lamp is operating properly, then disconnect the lamp wire harness connector or remove the lamp bulb. 3. Disconnect the battery negative cable. 4. Set an electronic digital multi-meter to its highest amperage scale. Connect the multi-meter between the disconnected battery negative cable terminal clamp and the battery negative terminal post. Make sure that the doors remain closed so that the illuminated entry system is not activated. The multi-meter amperage reading may remain high for up to three minutes, or may not give any reading at all while set in the highest amperage scale, depending upon the electrical equipment in the vehicle. The multi-meter leads must be securely clamped to the battery negative cable terminal clamp and the battery negative terminal post. If continuity between the battery negative terminal post and the negative cable terminal clamp is lost during any part of the IOD test, the electronic timer function will be activated and all of the tests will have to be repeated. 5. After about three minutes, the high-amperage IOD reading on the multi-meter should become very low or nonexistent, depending upon the electrical equipment in the vehicle. If the amperage reading remains high, remove and replace each fuse in the Power Distribution Center (PDC) , one at a time until the amperage reading becomes very low, or nonexistent. (Refer to 04 - Vehicle Quick Reference/Fuse Locations and Types - Specifications) for the appropriate wiring information for complete PDC and TIPM fuse, circuit breaker, and circuit identification. This will isolate each circuit and identify the circuit that is the source of the high-amperage IOD. If the amperage reading remains high after removing and replacing each fuse and circuit breaker, disconnect the wire harness from the generator. If the amperage reading now becomes very low or nonexistent, diagnose and repair the Charging System as necessary. After the high-amperage IOD has been corrected, switch the multi-meter to progressively lower amperage scales and, if necessary, repeat the fuse and circuit breaker remove-and-replace process to identify and correct all sources of excessive IOD. It is now safe to select the lowest milliampere scale of the multi-meter to check the low-amperage IOD.
CAUTION: Do not open any doors, or turn on any electrical accessories with the lowest milliampere scale selected, or the multi-meter may be damaged.

6. Observe the multi-meter reading. The low-amperage IOD should not exceed thirty-five milliamperes (0.035 ampere). If the current draw exceeds thirty-five milliamperes, isolate each circuit using the fuse and circuit breaker remove-and-replace process in Step #5 . The multi-meter reading will drop to within the acceptable limit when the source of the excessive current draw is disconnected. Repair this circuit as required; whether a wiring short, incorrect switch adjustment, or an inoperative component is the cause.

Posted on Jul 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 jeep liberty sport cigarette lighter fuse . which one is it? also need location of fuse for the cruise control and common problems/repair.


My info just said jeep liberty. Hope you can read it. Instrument panel power outlet. In the diagram, the top wire is voltage, the bottom wire is ground.
instrument panel power outlet-0k1jvpf5duujvnxanm5g0ntc-1-0.jpg

Mar 13, 2018 | Jeep Cars & Trucks

1 Answer

I'm looking for the location of the fuse panel on my 2003 jeep liberty


Owners manual will give location and fuse identification. Most fuse es are located in the underhood fuse relay center near the drivers side fender. It may also have an interior panel located on the drivers side under the dash area

Jun 21, 2015 | 2003 Jeep Liberty

1 Answer

Have a 2006 jeep liberty and the lights on the power windows switch will not work. Have checked fuse not sure what to do next.


make sure the dash lights are not on the dim setting. The window switch runs its lighting from the dash light dimming switch as well. If all is ok, I would suspect a faulty window switch assembly

Apr 05, 2015 | 2006 Jeep Liberty

1 Answer

Where's the light gauge fuse located for a 2003 jeep liberty?


The starter for a 2003 Jeep Liberty is located on the engine block under the car near the exhaust system. ---------------------------------------------------------------------------------
Digiprog 3

Apr 10, 2013 | Cars & Trucks

2 Answers

The fan for the heater/AC only works on the highest setting (4). Could this be a fuse?


no the blower switch on the dash board is at fault the high blower speed works off the relay only which is ok

Feb 20, 2010 | 2006 Jeep Liberty

1 Answer

Jeep Liberty 2006, interior dash light and radio light do not work. Not sure this is a fuse problem, any suggestions to what else I can troubleshoot?


usually when a dash light quits working it is a bulb that has burned out. you have to pull the dash and replace the bulb that is behind that has burned out. you can usuall find the bulbs at the auto parts store but some you have to get from the dealer. the auto part store sells some good repair manuals that should lead you step by step how to do it. if the book is sealed the cleark at the part store will usually let you open it to see if it has the details you are looking for. hope this helps.

Jan 30, 2010 | 2006 Jeep Liberty

1 Answer

2006 jeep liberty sport diagram


I would check alldata on line. at Alldata.com.
The site is the same the repair shops use to check the information you are looking for.

Good Luck

Oct 30, 2009 | 2006 Jeep Liberty

1 Answer

Help Please electrical or fuse problem 90 Cherokee


Try looking under the hood for a Maxi fuse

Aug 08, 2008 | 2006 Jeep Liberty

Not finding what you are looking for?
2006 Jeep Liberty Logo

Related Topics:

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

82322 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...