Question about Toyota Paseo

1 Answer

Can somebody please show me how to locate and replace my ignition coil on my 1992 toyota paseo.thanks

Posted by on

  • jotmc04 Jul 24, 2010

    thank a lot. it helps.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,272 Answers

Coil located inside distributor, Excluding California model Toyota Paseo . Coil located inside distributor.On California model the ignition coil located on the plug itself. To see how the ignition coil looks please check the fig below:-- can somebody please show me - 93eabf2.jpg
To replace the ignition coil the procedure is as follows:-- First remove the negative battery cable to prevent injuries or accidents. You'll need to remove the ground cable from the negative battery terminal post in order to do this. Loosen and detach the nuts and the clips that secure the cylinder head cover to the cylinder head. The only tool you should need for this is a wrench or a socket set.Determine whether you need to replace a single ignition coil or all the ignition coils. Each coil connects to a cylinder head and is held in place by a connector.Remove the connector from the  ignition coil. If you need to remove all of the ignition coils, you should remove all connectors.Pull up and twist on the ignition coil to free it from the cylinder head located in distributor.Verify that the new ignition coil works with your type of engine; universal and stock replacement ignition coils work with select models. Install the new  ignition coil.Secure the parts in place and reconnect the battery.Then check by starting the car. You have to take off the distributor cap. You should be able to see the coil immediately. Then unscrew the bolts connecting the wires and the unscrew the ones on the bottom. They're hard to get to so you might have to take a hose or two off to reach it better. If you can't get it out you might have to take the distributor itself out which is tough because you have to be careful about the timing. If the timing is off, the car will backfire when it's started. After you get the coil off, replace it with the new one, hook up the wires again and put the cap back on. Don't forget to disconnect the battery while you do this. Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Posted on Jul 16, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where on my toyota paseo 1992 can i find the igniter

Go to and then parts they should have a schematic that will help you.

Jun 03, 2014 | 1995 Toyota Corolla

1 Answer

I have a 1992 toyota paseo have changed the fuel pump and the fuel relay and it is still blowing the 15 amp fuse for the ignigtion can figure out why. thnx for the help

You may have a blown ignition module or a short at the coil, that's where this circuit goes. What I like to do when I run into a instantly blowing fuse, is wire in a headlight bulb to where the fuse normally is. A headlight has pretty low resistance so if you wire it in place of the fuse, it will pass enough current to operate most things that the fuse is there to protect if there was no short. With the bulb in place, you can go around the car wiggling wires and unplugging devices until you see the headlight go out, that means you have removed the short circuit and likely found what is blowing the fuse.

Mar 03, 2011 | 1992 Toyota Paseo

1 Answer

Cant find the gas relay for a 1992 toyota paseo. where can i get a diagram of the wiring for this car?

Your gas relay is located in the fuse box under the hood you will see 2 silver relays it is the one that is up and to the left. Hope that helps

Feb 13, 2011 | 1992 Toyota Paseo

1 Answer


Censor issue maybe. My brake lights did the same thing. I just readjusted the lining... around the trunk latch. And learned to pump my brakes after I turned the engine off. It finally worked itself out.

Feb 08, 2011 | 1992 Toyota Paseo

1 Answer

92 toyota paseo no spark

Please check your coil for malfunction. Check also the low voltage ( 12 VDC) presence there

Jan 28, 2011 | 1992 Toyota Paseo

1 Answer

What transmission fluid do i use in my 1992 toyota paseo

Hello, and welcome to FixYa.

According to the Toyota service manual, your 1992 Paseo requires Dexron II automatic transmission fluid.

Feb 09, 2010 | 1992 Toyota Paseo

1 Answer

How do i pull check engine codes for a 92 toyota

look for data link under hood. get a jumper wire.hook it to terminal E1 AND TE1.IF YOU CANT LOCATE IT.GET A HAYNES MANUAL.IT WILL MAKE IT EASY TO LOCATE.

Jul 25, 2009 | 1992 Toyota Paseo

1 Answer

1992 toyota paseo back lights

check fuses first usuall under dash/ and engine compartment/then check bulbs and the wiring to the lights make sure they are not pinched/ Please rate my response thank you very much

Feb 02, 2009 | 1992 Toyota Paseo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides